Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A50  Brake System Malfunction  


DESCRIPTION

·

for 2TR-FE:

When the pre-crash safety system is operating, the driving support ECU assembly sends brake control signals to the skid control ECU (brake actuator assembly).

If the driving support ECU assembly receives an vehicle stability control system malfunction signal from the skid control ECU (brake actuator assembly) via CAN communication, DTC C1A50 will be stored.

·

except 2TR-FE:

When the pre-crash safety system is operating, the driving support ECU assembly sends brake control signals to the skid control ECU (master cylinder solenoid).

If the driving support ECU assembly receives an vehicle stability control system malfunction signal from the skid control ECU (master cylinder solenoid) via CAN communication, DTC C1A50 will be stored.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1A50 Brake System Malfunction
·

for 2TR-FE:

While the ignition switch is ON, the driving support ECU assembly receives an vehicle stability control system malfunction signal from the skid control ECU (brake actuator assembly) for 0.3 seconds or more.

·

except 2TR-FE:

While the ignition switch is ON, the driving support ECU assembly receives an vehicle stability control system malfunction signal from the skid control ECU (master cylinder solenoid) for 0.3 seconds or more.


·

Vehicle stability control system

·

Skid control ECU assembly (brake actuator assembly) (for 2TR-FE)

·

Skid control ECU assembly (master cylinder solenoid) (except 2TR-FE)

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

The pre-crash safety system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)
HINT:

Pre-crash safety system DTC C1A50 may be stored due to a malfunction in the vehicle stability control system. Therefore, it is necessary to check for and troubleshoot vehicle stability control system DTCs first.



Result:
Result Proceed to
Vehicle stability control system DTCs are not output A
Vehicle stability control system DTC are output (for 2TR-FE) B
Vehicle stability control system DTC are output (except 2TR-FE) C



A

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

B

C

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC C1A50 is not output A
DTC C1A50 is output B



A

B

3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
4.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC C1A50 is not output A
DTC C1A50 is output (for 2TR-FE) B
DTC C1A50 is output (except 2TR-FE) C



A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B

C