for 2TR-FE:
The brake actuator assembly sends signals to the driving support ECU assembly according to the brake control status. If the driving support ECU assembly receives a vehicle stability control system malfunction signal from the brake actuator assembly, it will store DTC C1A64.
except 2TR-FE:
The master cylinder solenoid sends signals to the driving support ECU assembly according to the brake control status. If the driving support ECU assembly receives a vehicle stability control system malfunction signal from the master cylinder solenoid, it will store DTC C1A64.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A64 | Brake Control Signal Mismatch | ·
for 2TR-FE: While the ignition switch is ON, the driving support ECU assembly receives a vehicle stability control system malfunction signal from the skid control ECU (brake actuator assembly) continuously for 0.5 seconds or more. ·
except 2TR-FE: While the ignition switch is ON, the driving support ECU assembly receives a vehicle stability control system malfunction signal from the skid control ECU (master cylinder solenoid) continuously for 0.5 seconds or more. |
·
Vehicle stability control system ·
Skid control ECU assembly (brake actuator assembly) (for 2TR-FE) ·
Skid control ECU assembly (master cylinder solenoid) (except 2TR-FE) ·
Driving support ECU assembly |
When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
The pre-crash safety system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Pre-crash safety system DTC C1A64 may be stored due to a malfunction in the vehicle stability control system. Therefore, it is necessary to check for and troubleshoot vehicle stability control system DTCs first.
Check for DTCs.
for 2TR-FE: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR
except 2TR-FE: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Vehicle stability control system DTCs are not output | A |
| Vehicle stability control system DTC are output (for 2TR-FE) | B |
| Vehicle stability control system DTC are output (except 2TR-FE) | C |
A
B
C
Clear the DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A64 is not output | A |
| DTC C1A64 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Replace the driving support ECU assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A64 is not output | A |
| DTC U1104 is output (for 2TR-FE) | B |
| DTC U1104 is output (except 2TR-FE) | C |
A
B
C
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for LHD)>DISASSEMBLY
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for RHD)>DISASSEMBLY