Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror) › from 2017.08
RM27T0E _59 Vehicle Exterior _053745 MIRROR (EXT) _0327116 POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror)  AUTO Power Retract Mirrors do not operate  


DESCRIPTION

When the outer mirror switch assembly is set to AUTO (neutral position), an AUTO signal is detected by the main body ECU (multiplex network body ECU). When locking and unlocking all doors with the ignition switch off, the main body ECU (multiplex network body ECU) sends deploy/retract signals to the outer mirror control ECU assembly via CAN communication. The outer mirror control ECU assembly deploys and retracts the outer rear view mirror assembly based on the received signals.

WIRING DIAGRAM

E378109E01
0.906,2.74 2.854,3.01 1.948,0.271 10 false Outer Mirror Switch Assembly 0.906,2.563 2.896,2.76 1.99,0.198 10 false G11*1, G196*2 0.281,6.781 1.031,6.969 0.75,0.188 10 false *1: for LHD 0.271,7.094 1.021,7.281 0.75,0.188 10 false *2: for RHD 0.677,7.406 2.385,7.583 1.708,0.177 10 false : CAN Communication Line 5.073,1.938 6.74,2.26 1.667,0.323 10 false Main Body ECU (Multiplex Network Body ECU) 5.198,4.667 5.49,4.875 0.292,0.208 10 false z18 5.146,6.885 5.469,7.115 0.323,0.229 10 false z19 5.167,4.865 6.719,5.26 1.552,0.396 10 false Outer Mirror Control ECU Assembly LH 5.135,7.042 6.688,7.438 1.552,0.396 10 false Outer Mirror Control ECU Assembly RH 1.667,4.052 3.396,4.302 1.729,0.25 10 false Power Retract Mirror Motor 1.938,4.594 4.281,4.813 2.344,0.219 10 false Outer Rear View Mirror Assembly LH 1.833,6.823 4.177,7.042 2.344,0.219 10 false Outer Rear View Mirror Assembly RH 2.99,0.271 3.76,0.469 0.771,0.198 10 false MR 3.354,0.25 4.125,0.448 0.771,0.198 10 false 8*1, 17*2 5.083,1.771 5.698,1.969 0.615,0.198 10 false G216 5.167,0.219 5.938,0.417 0.771,0.198 10 false 14 2.927,0.542 3.698,0.74 0.771,0.198 10 false MAT 3.344,0.542 4.115,0.74 0.771,0.198 10 false 11 5.438,0.677 6.354,0.875 0.917,0.198 10 false AMR 5.156,0.552 5.927,0.75 0.771,0.198 10 false 11 5.448,0.375 6.365,0.573 0.917,0.198 10 false RET 5.458,3.833 5.771,4.031 0.313,0.198 10 false MR 5.458,4.219 5.771,4.417 0.313,0.198 10 false MF 5.458,6.458 5.771,6.656 0.313,0.198 10 false MF 5.458,6.094 5.771,6.292 0.313,0.198 10 false MR 5.24,3.74 5.396,3.938 0.156,0.198 10 false 3 5.177,4.115 5.427,4.323 0.25,0.208 10 false 11 5.167,6.333 5.5,6.531 0.333,0.198 10 false 11 5.219,5.958 5.375,6.156 0.156,0.198 10 false 3 3.104,1.75 3.26,1.948 0.156,0.198 10 false E 3.375,1.75 4.146,1.948 0.771,0.198 10 false 10 0.885,0.802 1.5,1 0.615,0.198 10 false Fold 2.458,0.823 3.375,1.021 0.917,0.198 10 false Unfold 1.688,0.573 2.302,0.771 0.615,0.198 10 false Auto 1.146,2.031 2.5,2.271 1.354,0.24 10 false Mirror Retract Switch 1.688,6.271 3.417,6.521 1.729,0.25 10 false Power Retract Mirror Motor

CAUTION / NOTICE / HINT

NOTICE:
·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

*: w/ Door Control Battery



PROCEDURE

1.CHECK POWER RETRACT MIRROR FUNCTION
a.

Check power retract mirror function.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>OPERATION CHECK

OK:

Power retract mirror function is normal.



Result:
Proceed to
OK
NG



OK

2.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

NG

GO TO OTHER FLOWCHART (Power Retractable Mirrors do not Operate with Power Retract Mirror Switch)

2.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check the wireless door lock control system.


OK:

Wireless door lock control system is normal.



Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

3.CHECK ENTRY AND START SYSTEM (for Entry Function)

B

4.READ VALUE USING GTS (MIRROR RETRACT)

C

3.CHECK ENTRY AND START SYSTEM (for Entry Function)
a.

Check the entry and start system (for Entry Function).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK

OK:

Entry and start system (for Entry Function) is normal.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (MIRROR RETRACT)

NG

4.READ VALUE USING GTS (MIRROR RETRACT)
a.

Using the GTS, read the Data List.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Data List
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Auto Mirror SW Auto retractable outer mirror switch signal / OFF or ON OFF: Auto retractable outer mirror switch off
ON: Auto retractable outer mirror switch on
-

OK:

On the GTS screen, ON or OFF is displayed for each item according to the table above.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

5.INSPECT OUTER MIRROR SWITCH ASSEMBLY (MIRROR RETRACTOR SWITCH)
5.INSPECT OUTER MIRROR SWITCH ASSEMBLY (MIRROR RETRACTOR SWITCH)
a.

Remove the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL


b.

Inspect the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the G11*1 or G196*2 outer mirror switch assembly connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G216 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G11-8 (MR) - G216-14 (RET) Always Below 1 Ω
G11-11 (MAT) - G216-11 (AMR) Always Below 1 Ω
G11-10 (E) - Body ground Always Below 1 Ω
G11-8 (MR) or G216-14 (RET) - Body ground Always 10 kΩ or higher
G11-11 (MAT) or G216-11 (AMR) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G196-17 (MR) - G216-14 (RET) Always Below 1 Ω
G196-11 (MAT) - G216-11 (AMR) Always Below 1 Ω
G196-10 (E) - Body ground Always Below 1 Ω
G196-17 (MR) or G216-14 (RET) - Body ground Always 10 kΩ or higher
G196-11 (MAT) or G216-11 (AMR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR