Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2017.08–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in lock-up when the brakes are suddenly applied.

When the brake pedal is depressed, this switch sends a signal to the TCM. Then the TCM cancels the operation of the lock-up clutch while braking is in progress.

DTC Code DTC Detection Condition Trouble Area
P0724 Stop light switch remains on even when the vehicle is driven in a stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) pattern 5 times (2-trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch

·

TCM



MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during stop and go driving, the TCM interprets this as a fault in the stop light switch. Then the MIL illuminates and the TCM stores the DTC. The vehicle must stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) 5 times for 2 driving cycles in order for the DTC to be stored.

WIRING DIAGRAM

C272585E06
3.844,1.885 5,2.073 1.156,0.188 10 false Stop Light Switch 3.844,1.719 4.271,1.906 0.427,0.188 10 false A99 5.698,3.063 6.115,3.25 0.417,0.188 10 false TCM 5.708,2.896 6.135,3.083 0.427,0.188 10 false G70 5.5,1.385 5.917,1.573 0.417,0.188 10 false STP 5.208,1.49 5.417,1.677 0.208,0.188 10 false 14 3.927,1.5 4.073,1.688 0.146,0.188 10 false 7 4.719,1.5 4.865,1.688 0.146,0.188 10 false 3 3.01,1.531 3.479,1.719 0.469,0.188 10 false STOP 2.073,1.531 2.667,1.719 0.594,0.188 10 false ALT 1.635,2.417 2.24,2.604 0.604,0.188 10 false Battery 4.542,1.375 4.729,1.563 0.188,0.188 10 false L 4.115,1.375 4.302,1.563 0.188,0.188 10 false B

PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Data List / Stop Light Switch.


e.

Read the value displayed on the GTS when the brake pedal is depressed and released.

ECT:
Tester Display Measurement Item/Range Normal Condition
Stop Light Switch Stop light switch status/
ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released






OK

NG

2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the stop light switch assembly installation (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION).

OK:

Stop light switch is installed correctly.




OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - TCM)

NG

SECURELY REINSTALL STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - TCM)
a.

Disconnect the A99 stop light switch connector.


b.

Disconnect the G70 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A99-3 (L) - G70-14 (STP) Always Below 1 Ω
A99-3 (L) - Body ground Always 10 kΩ or higher
G70-14 (STP) - Body ground Always 10 kΩ or higher




OK

4.CHECK STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK STOP LIGHT SWITCH ASSEMBLY
a.

Check the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).



OK

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY