Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  Crawl Indicator Light does not Come ON  


DESCRIPTION

If the following condition is met, the crawl indicator light turns off and crawl control is stopped.

Crawl control is operated when the vehicle stability control system is malfunctioning, or a vehicle stability control system malfunction occurs during crawl control.


If any of the following conditions are met, the crawl indicator light blinks and crawl control is stopped.

·

The transfer is shifted to H4 during crawl control.

·

The shift lever is moved to P or N during crawl control.

·

The driver side door is opened during crawl control.


When the vehicle is driven at 25 km/h (16 mph) or more during crawl control, control is temporarily stopped and the crawl indicator light blinks.

When using crawl control continually for a long period of time, if the temperature inside the hydraulic brake booster becomes too high, the crawl indicator light will turn off. After a while, the temperature decreases and crawl control becomes operable.

WIRING DIAGRAM

C256732E12
5.344,3.323 5.646,3.51 0.302,0.188 10 false A7 5.323,3.531 7.021,4 1.698,0.469 10 false Skid Control ECU (Master Cylinder Solenoid) 5.729,1.948 6.167,2.115 0.438,0.167 10 false TRM1 5.76,1.604 6.24,1.813 0.479,0.208 10 false TRS 5.719,2.25 6.198,2.469 0.479,0.219 10 false TRM2 5.719,2.573 6.177,2.792 0.458,0.219 10 false TRM3 5.438,1.771 5.667,1.969 0.229,0.198 10 false 44 5.438,1.448 5.667,1.656 0.229,0.208 10 false 43 5.458,2.135 5.677,2.365 0.219,0.229 10 false 21 5.448,2.458 5.688,2.688 0.24,0.229 10 false 13 3.51,1.583 3.948,1.75 0.438,0.167 10 false FRB 3.583,2.229 3.885,2.396 0.302,0.167 10 false UP 3.49,1.906 3.927,2.073 0.438,0.167 10 false ECU 3.615,2.542 4.052,2.708 0.438,0.167 10 false DN 3.906,1.49 4.302,1.729 0.396,0.24 10 false 21 3.906,1.792 4.323,2.052 0.417,0.26 10 false 17 3.906,2.125 4.313,2.354 0.406,0.229 10 false 18 3.906,2.458 4.427,2.656 0.521,0.198 10 false 19 2.74,2.479 3.01,2.729 0.271,0.25 10 false E 2.448,2.344 2.823,2.5 0.375,0.156 10 false 24 2.677,2.958 3.052,3.115 0.375,0.156 10 false G156 2.677,3.156 4.635,3.365 1.958,0.208 10 false Combination Switch Assembly 0.292,4.333 0.729,4.531 0.438,0.198 10 false G304 0.292,4.542 2.208,4.76 1.917,0.219 10 false Combination Meter Assembly 0.74,5.083 2.833,5.365 2.094,0.281 10 false : CAN Communication System

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).


PROCEDURE

2.CHECK FOR TEST MODE DTC
a.

Perform the downhill assist control switch check in the Test Mode Procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>TEST MODE PROCEDURE).

OK:

Test mode DTC C1379 is cleared.




OK

3.PERFORM ACTIVE TEST USING GTS (CRAWL CONTROL LIGHT)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - MASTER CYLINDER SOLENOID)
3.PERFORM ACTIVE TEST USING GTS (CRAWL CONTROL LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Crawl Control Light Crawl indicator light Indicator light ON/OFF Observe combination meter


f.

When performing the Crawl Control Light Active Test, check Crawl Control Light in the Data List.

(See pageBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DATA LIST / ACTIVE TEST)

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Crawl Control Light Crawl indicator light/ ON or OFF ON: Indicator light on
OFF: Indicator light off
-

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C
OFF Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C



A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

C

4.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - MASTER CYLINDER SOLENOID)

OK

5.INSPECT COMBINATION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT COMBINATION SWITCH ASSEMBLY
a.

Remove the combination switch assembly (See pageBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH>REMOVAL).


b.

Inspect the combination switch assembly (See pageBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH>INSPECTION).


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


A

B

C

REPLACE COMBINATION SWITCH ASSEMBLY