Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2017.08
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0261225 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

When the ignition switch is ON, the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) is operated by the multiplex network master switch assembly. The front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has motor, regulator and ECU functions.


WIRING DIAGRAM

B449851E02
1.729,0.979 5.042,1.198 3.313,0.219 10 false Main Body ECU (Multiplex Network Body ECU) 1,1.5 1.917,1.75 0.917,0.25 10 false from Battery 0.5,3.083 1.417,3.333 0.917,0.25 10 false from Battery 3.083,4.813 4.688,5.198 1.604,0.385 10 false Multiplex Network Master Switch Assembly 5.083,4.833 7.021,5.25 1.938,0.417 10 false Front Power Window Regulator Motor Assembly LH 5.083,5.917 7.021,6.333 1.938,0.417 10 false Front Power Window Regulator Motor Assembly RH 5.083,4.635 5.698,4.833 0.615,0.198 10 false K7*1 5.083,5.719 5.698,5.917 0.615,0.198 10 false J7*2 3.083,4.625 4.083,4.875 1,0.25 10 false K4*1, J9*2 2.25,3.292 2.833,3.542 0.583,0.25 10 false DOOR*3 2.719,1.688 3.385,1.938 0.667,0.25 10 false DOOR D 0.5,6.417 2.333,6.667 1.833,0.25 10 false : LIN Communication Line 0.167,5.75 1.083,5.917 0.917,0.167 10 false *1: for LHD 0.167,6.083 1.083,6.25 0.917,0.167 10 false *2: for RHD 3.802,3.583 4.385,3.833 0.583,0.25 10 false DOWN 5.667,3.583 6.25,3.833 0.583,0.25 10 false DOWN 3.344,4.052 3.802,4.25 0.458,0.198 10 false GND 5.667,2.188 6.125,2.385 0.458,0.198 10 false GND 4.021,2.969 4.333,3.167 0.313,0.198 10 false UP 5.667,2.969 5.979,3.167 0.313,0.198 10 false UP 3.344,3.115 3.5,3.313 0.156,0.198 10 false B 5.656,1.5 5.813,1.698 0.156,0.198 10 false B 3.021,3 3.333,3.198 0.313,0.198 10 false 11 3.031,3.938 3.344,4.135 0.313,0.198 10 false 12 4.385,2.844 4.698,3.042 0.313,0.198 10 false 20 4.385,3.479 4.698,3.677 0.313,0.198 10 false 15 5.354,2.844 5.667,3.042 0.313,0.198 10 false 10 5.417,1.385 5.573,1.583 0.156,0.198 10 false 2 5.427,2.073 5.583,2.271 0.156,0.198 10 false 1 5.427,3.49 5.583,3.688 0.156,0.198 10 false 7 2.25,3.521 3.052,3.75 0.802,0.229 10 false DOOR B*4 1.313,5.75 2.229,5.917 0.917,0.167 10 false *3: for 5L-E 1.313,6.063 2.469,6.25 1.156,0.188 10 false *4: except 5L-E

CAUTION / NOTICE / HINT

NOTICE:
·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

If the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

*: w/ Door Control Battery




PROCEDURE

1.READ VALUE USING GTS (MAIN BODY)
a.

Read the Data List according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Communication D-Door Motor Connection status between front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) and main body ECU (multiplex network body ECU) / OFF or ON STOP: Communication stopped
OK: Normal communication
-
Communication Master SW Connection status between multiplex network master switch assembly and main body ECU (multiplex network body ECU) STOP: Communication stopped
OK: Normal communication
-

OK:

On the GTS screen, OK is displayed.




OK

2.READ VALUE USING GTS (D-DOOR MOTOR)

NG

2.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal / OFF or ON OFF: Driver door power window manual up switch not being operated
ON: Driver door power window manual up switch being operated
-
D Door P/W Down SW Driver door power window manual down switch signal / OFF or ON OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

3.PERFORM ACTIVE TEST USING GTS (D-DOOR MOTOR)

B

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

C

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
3.PERFORM ACTIVE TEST USING GTS (D-DOOR MOTOR)
a.

Perform the Active Test according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


D-Door Motor
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF/UP/DOWN -

HINT:

Up and down movement does not occur if the arrow is not pressed and held


OK:

Driver door power window operates normally.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

C

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the K4 multiplex network master switch assembly connector.


b.

Disconnect the K7 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K4-20 (UP) - K7-10 (UP) Always Below 1 Ω
K4-15 (DOWN) - K7-7 (DOWN) Always Below 1 Ω
K4-20 (UP) or K7-10 (UP) - Body ground Always 10 kΩ or higher
K4-15 (DOWN) or K7-7 (DOWN) - Body ground Always 10 kΩ or higher




OK

5.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Replace the multiplex network master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).



NEXT

6.CHECK MANUAL UP / DOWN FUNCTION (FOR DRIVER DOOR)
6.CHECK MANUAL UP / DOWN FUNCTION (FOR DRIVER DOOR)
a.

Check that the driver door power window moves when the manual up and down function of the multiplex network master switch assembly is operated (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Driver door manual up and down function is normal.




OK

END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the J9 multiplex network master switch assembly connector.


b.

Disconnect the J7 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J9-20 (UP) - J7-10 (UP) Always Below 1 Ω
J9-15 (DOWN) - J7-7 (DOWN) Always Below 1 Ω
J9-20 (UP) - Body ground Always 10 kΩ or higher
J9-15 (DOWN) - Body ground Always 10 kΩ or higher




OK

8.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Replace the multiplex network master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).



NEXT

9.CHECK MANUAL UP / DOWN FUNCTION
9.CHECK MANUAL UP / DOWN FUNCTION
a.

Check that the driver door power window moves when the manual up and down function of the multiplex network master switch assembly is operated (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Driver door manual up and down function is normal.




OK

END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH