Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › 2017.08–2020.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  C1380  Stop Light Control Relay Malfunction  


DESCRIPTION

When the skid control ECU (master cylinder solenoid) applies the brakes after receiving a brake request signal from the pre-collision system, dynamic radar cruise control system, secondary collision brake system or brake hold control system, the skid control ECU (master cylinder solenoid) operates the stop light control relay (stop light switch assembly) to illuminate the stop lights.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1380 Stop Light Control Relay Malfunction Either condition is met:
·

When the voltage at the +BS terminal is between 10 V or more and the stop light control relay (stop light switch assembly) drive output (STPO) is on, a signal is not input to the STP terminal for 5 seconds or more.

·

When the voltage at the +BS terminal is between 10 V or more and the stop light control relay (stop light switch assembly) drive output (STPO) is off, the signal at the STP2 terminal is different from the input signal at the STP terminal for 5 seconds or more.


·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (Master cylinder solenoid)

·

Rear combination light assembly LH

·

Rear combination light assembly RH

·

Center stop light assembly

·

Shift lock control ECU (Shift lock control unit assembly)

·

Certification ECU (Smart key ECU assembly)

·

ECM

·

Transmission control ECU assembly (for 1KD-FTV)



HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C384433E01
0.115,0.083 2.063,0.323 1.948,0.24 12 false w/ Manual Transmission: 2.208,0.719 2.667,0.917 0.458,0.198 10 false STP 0.885,1.156 3.031,1.531 2.146,0.375 10 false Shift Lock Control ECU (Shift Lock Control Unit Assembly) 2.688,0.521 2.896,0.719 0.208,0.198 10 false 4 2.552,0.719 2.906,0.927 0.354,0.208 10 false G150 2.635,0.917 2.875,1.135 0.24,0.219 10 false *1 3.063,0.521 3.271,0.74 0.208,0.219 10 false 6 2.948,0.719 3.406,0.917 0.458,0.198 10 false G45 3.021,0.917 3.323,1.125 0.302,0.208 10 false *2 4.354,0.521 4.625,0.708 0.271,0.188 10 false 38 4.771,0.521 5.01,0.75 0.24,0.229 10 false 8 5.094,0.521 5.344,0.719 0.25,0.198 10 false 10 5.448,0.51 5.708,0.698 0.26,0.188 10 false 13 5.771,0.708 6.229,0.906 0.458,0.198 10 false STP 5.354,0.719 5.76,0.885 0.406,0.167 10 false G185 5.01,0.719 5.385,0.885 0.375,0.167 10 false G180 4.677,0.719 5.052,0.896 0.375,0.177 10 false G57 4.323,0.719 4.781,0.917 0.458,0.198 10 false G56 4.396,0.948 4.635,1.167 0.24,0.219 10 false *3 4.76,0.958 4.979,1.156 0.219,0.198 10 false *4 5.115,0.948 5.406,1.125 0.292,0.177 10 false *5 5.469,0.948 5.677,1.146 0.208,0.198 10 false *6 5.75,1.125 6.292,1.323 0.542,0.198 10 false ECM 5.563,1.594 5.781,1.792 0.219,0.198 10 false 2 5.771,1.677 6.229,1.875 0.458,0.198 10 false STP1 4.302,1.958 4.802,2.146 0.5,0.188 10 false G213 4.302,2.104 7.156,2.333 2.854,0.229 10 false Certification ECU (Smart Key ECU Assembly) 0.74,2.354 2.271,2.573 1.531,0.219 10 false from Battery 0.958,3.573 1.469,3.771 0.51,0.198 10 false STOP 1.552,3.302 1.771,3.51 0.219,0.208 10 false 7 1.771,3.302 1.948,3.521 0.177,0.219 10 false B 3.135,2.99 3.333,3.188 0.198,0.198 10 false L 3.344,2.99 3.604,3.188 0.26,0.198 10 false 3 4.646,3 4.927,3.24 0.281,0.24 10 false 45 4.958,2.99 5.417,3.188 0.458,0.198 10 false STP2 4.656,3.885 4.917,4.135 0.26,0.25 10 false 16 4.958,3.875 5.417,4.073 0.458,0.198 10 false STPO 4.958,4.865 5.271,5.063 0.313,0.198 10 false STP 4.719,4.854 4.927,5.063 0.208,0.208 10 false 7 4.844,5.833 5.302,6.031 0.458,0.198 10 false A7 4.844,5.99 6.479,6.375 1.635,0.385 10 false Skid Control ECU (Master Cylinder Solenoid) 3.344,3.865 3.802,4.063 0.458,0.198 10 false 4 2.948,3.875 3.302,4.063 0.354,0.188 10 false ACC 1.552,4.896 1.802,5.125 0.25,0.229 10 false 2 1.76,4.896 2.219,5.094 0.458,0.198 10 false GND 1.688,5.479 2.146,5.677 0.458,0.198 10 false A99 1.677,5.635 3.656,5.844 1.979,0.208 10 false Stop Light Switch Assembly 2.948,4.854 3.406,5.052 0.458,0.198 10 false OUT 3.333,4.865 3.604,5.073 0.271,0.208 10 false 1 1.625,6.198 1.854,6.396 0.229,0.198 10 false 4 1.792,6.198 1.99,6.406 0.198,0.208 10 false E 1.49,6.698 1.948,6.896 0.458,0.198 10 false R22 1.479,6.823 3.99,7.01 2.51,0.188 10 false Rear Combination Light Assembly LH 2.156,6.479 2.583,6.677 0.427,0.198 10 false Stop 2.563,6.188 2.896,6.365 0.333,0.177 10 false STP 2.927,6.188 3.156,6.417 0.229,0.229 10 false 1 4.792,7.302 4.958,7.5 0.167,0.198 10 false 1 6.156,7.292 6.396,7.5 0.24,0.208 10 false 2 5.167,7.844 5.365,8.031 0.198,0.188 10 false Z1 5.177,8.042 6.302,8.396 1.125,0.354 10 false Center Stop Light Assembly 3.333,7.635 3.531,7.833 0.198,0.198 10 false *8 3.281,7.448 3.74,7.646 0.458,0.198 10 false R21 3.354,7.229 3.594,7.438 0.24,0.208 10 false 1 2.99,7.229 3.188,7.417 0.198,0.188 10 false 1 2.917,7.448 3.375,7.646 0.458,0.198 10 false Q31 2.958,7.635 3.177,7.823 0.219,0.188 10 false *7 1.583,7.302 1.74,7.5 0.156,0.198 10 false 4 1.802,7.302 2.01,7.542 0.208,0.24 10 false E 2.156,7.604 2.531,7.781 0.375,0.177 10 false Stop 2.552,7.313 2.896,7.542 0.344,0.229 10 false STP 0.021,8.177 2.01,8.396 1.99,0.219 10 false *1: w/o Entry and Start System 0.031,8.521 2.094,8.75 2.063,0.229 10 false *2: w/ Entry and Start System 2.031,8.188 3.052,8.365 1.021,0.177 10 false *3: for 1GR-FE 2.021,8.531 3.271,8.74 1.25,0.208 10 false *4: for 1KD-FTV 3.031,8.167 4.24,8.323 1.208,0.156 10 false *5: for 2TR-FE 3.042,8.531 4.385,8.719 1.344,0.188 10 false *6: for 1GD-FTV 4.156,8.521 5.542,8.719 1.385,0.198 10 false *8: for 5 Door 4.146,8.198 5.813,8.396 1.667,0.198 10 false *7: for 3 Door 1.479,7.833 3.99,8.021 2.51,0.188 10 false Rear Combination Light Assembly RH

C384434E01
0.115,8.25 2.219,8.521 2.104,0.271 10 false *1: w/o Entry and Start System 0.104,8.542 2.26,8.781 2.156,0.24 10 false *2: w/ Entry and Start System 2.104,8.26 4.26,8.5 2.156,0.24 10 false *3: for 1GR-FE 2.104,8.542 4.26,8.781 2.156,0.24 10 false *4: for 1KD-FTV 3.156,8.25 5.313,8.49 2.156,0.24 10 false *5: for 2TR-FE 3.156,8.531 5.313,8.771 2.156,0.24 10 false *6: for 1GD-FTV 4.25,8.521 6.406,8.76 2.156,0.24 10 false *8: for 5 Door 4.24,8.25 6.396,8.49 2.156,0.24 10 false *7: for 3 Door 0.104,0.073 2.26,0.302 2.156,0.229 12 false w/ Automatic Transmission: 2.167,0.729 2.49,0.917 0.323,0.188 10 false STP 0.042,1.115 3.635,1.333 3.594,0.219 10 false Shift Lock Control ECU (Shift Lock Control Unit Assembly) 2.667,0.5 2.833,0.698 0.167,0.198 10 false 4 2.542,0.729 2.99,0.917 0.448,0.188 10 false G150 2.615,0.938 2.865,1.115 0.25,0.177 10 false *1 3.031,0.5 3.229,0.719 0.198,0.219 10 false 6 2.948,0.719 3.375,0.906 0.427,0.188 10 false G45 4.375,0.5 4.698,0.688 0.323,0.188 10 false 35 4.792,0.5 5,0.698 0.208,0.198 10 false 8 5.094,0.5 5.333,0.708 0.24,0.208 10 false 10 5.438,0.51 5.76,0.698 0.323,0.188 10 false 13 5.771,0.698 6.094,0.885 0.323,0.188 10 false STP 5.365,0.729 5.917,0.917 0.552,0.188 10 false G185 5.01,0.729 5.521,0.927 0.51,0.198 10 false G180 4.688,0.719 5.01,0.906 0.323,0.188 10 false G57 4.323,0.729 4.646,0.917 0.323,0.188 10 false G56 4.396,0.948 4.719,1.135 0.323,0.188 10 false *3 4.76,0.948 5.083,1.135 0.323,0.188 10 false *4 5.115,0.948 5.438,1.135 0.323,0.188 10 false *5 5.458,0.948 5.781,1.135 0.323,0.188 10 false *6 5.802,1.125 6.125,1.313 0.323,0.188 10 false ECM 5.781,1.688 6.302,1.885 0.521,0.198 10 false STP1 4.292,1.969 4.677,2.156 0.385,0.188 10 false G213 4.292,2.135 7.146,2.333 2.854,0.198 10 false Certification ECU (Smart Key ECU Assembly) 5.552,1.573 5.729,1.781 0.177,0.208 10 false 2 3.302,1.583 3.521,1.792 0.219,0.208 10 false 14 2.927,1.719 3.281,1.906 0.354,0.188 10 false STP 1.958,2.094 2.333,2.281 0.375,0.188 10 false G70 1.958,2.25 2.781,2.438 0.823,0.188 10 false TCM*4 0.75,2.365 1.74,2.625 0.99,0.26 10 false from Battery 0.958,3.583 1.458,3.813 0.5,0.229 10 false STOP 1.552,3.292 1.75,3.5 0.198,0.208 10 false 7 1.76,3.302 1.99,3.542 0.229,0.24 10 false B 3.135,2.969 3.344,3.188 0.208,0.219 10 false L 3.375,2.969 3.573,3.177 0.198,0.208 10 false 3 4.646,2.969 4.906,3.167 0.26,0.198 10 false 45 4.927,2.969 5.406,3.156 0.479,0.188 10 false STP2 4.708,4.875 4.917,5.094 0.208,0.219 10 false 7 4.927,3.865 5.469,4.052 0.542,0.188 10 false STPO 4.927,4.875 5.25,5.063 0.323,0.188 10 false STP 4.635,3.875 4.854,4.063 0.219,0.188 10 false 16 3.375,3.865 3.625,4.083 0.25,0.219 10 false 4 2.938,3.865 3.26,4.052 0.323,0.188 10 false ACC 2.927,4.865 3.302,5.052 0.375,0.188 10 false OUT 3.365,4.865 3.792,5.094 0.427,0.229 10 false 1 1.75,4.875 2.135,5.115 0.385,0.24 10 false GND 1.563,4.875 1.771,5.073 0.208,0.198 10 false 2 1.688,5.49 2.135,5.719 0.448,0.229 10 false A99 1.677,5.635 3.74,5.865 2.063,0.229 10 false Stop Light Switch Assembly 4.833,5.823 5.125,6.083 0.292,0.26 10 false A7 4.833,6.01 7,6.344 2.167,0.333 10 false Skid Control ECU (Master Cylinder Solenoid) 1.625,6.188 1.917,6.448 0.292,0.26 10 false 4 1.813,6.188 2.104,6.448 0.292,0.26 10 false E 1.521,6.708 1.813,6.969 0.292,0.26 10 false R22 1.542,6.844 3.917,7.083 2.375,0.24 10 false Rear Combination Light Assembly LH 2.552,6.188 2.844,6.448 0.292,0.26 10 false STP 2.927,6.177 3.219,6.438 0.292,0.26 10 false 1 6.146,7.302 6.438,7.563 0.292,0.26 10 false 2 4.792,7.302 5.083,7.563 0.292,0.26 10 false 1 5.333,7.833 5.635,8.063 0.302,0.229 10 false Z1 5.333,7.979 6.448,8.333 1.115,0.354 10 false Center Stop Light Assembly 3.365,7.219 3.656,7.479 0.292,0.26 10 false 1 3.26,7.438 3.552,7.698 0.292,0.26 10 false R21 3.354,7.635 3.646,7.896 0.292,0.26 10 false *8 2.552,7.313 2.844,7.573 0.292,0.26 10 false STP 2.917,7.438 3.208,7.698 0.292,0.26 10 false Q31 2.979,7.229 3.271,7.49 0.292,0.26 10 false 1 2.135,7.615 2.51,7.865 0.375,0.25 10 false Stop 2.167,6.49 2.573,6.75 0.406,0.26 10 false Stop 1.802,7.313 2.021,7.542 0.219,0.229 10 false E 1.615,7.313 1.906,7.573 0.292,0.26 10 false 4 3.031,0.927 3.281,1.104 0.25,0.177 10 false *2 2.979,7.635 3.271,7.896 0.292,0.26 10 false *7 1.552,7.844 3.927,8.083 2.375,0.24 10 false Rear Combination Light Assembly RH

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (master cylinder solenoid), perform system variant learning and acceleration sensor zero point calibration (See pageBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STP2, STPO AND STP TERMINAL)
a.
U148398C02
1.948,0.604 1.688,1.146 true 2.875,0.604 2.635,1.135 true 2.531,1.521 2.344,1.865 true 1.031,0.646 1.229,0.813 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.156,1.906 2.563,2.073 0.406,0.167 10 false STP2 1.865,0.396 2.219,0.573 0.354,0.177 10 false STP 2.729,0.396 3.177,0.573 0.448,0.177 10 false STPO
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Turn the engine switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-7 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-7 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V
A7-16 (STPO) - Body ground Always 11 to 14 V
A7-45 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-45 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Result Proceed to
All terminal voltages are normal A
Only STP2 terminal voltage abnormal B
Only STPO terminal voltage abnormal C
Only STP terminal voltage abnormal D
STPO terminal and STP terminal voltage abnormal E



A

2.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

B

5.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - SMART KEY ECU ASSEMBLY)

C

11.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)

D

12.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - REAR COMBINATION LIGHT ASSEMBLY LH)

E

17.CHECK STOP LIGHT SWITCH ASSEMBLY POWER SOURCE CIRCUIT
2.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Reconnect the A7 skid control ECU (master cylinder solenoid) connector.


b.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay OFF/ON Stop lights come on

OK:

Stop light turns ON/OFF in response to the GTS operation



Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC

NG

4.INSPECT MASTER CYLINDER SOLENOID
3.CHECK FOR DTC

b.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay OFF/ON Stop lights come on


c.

According to the display on the GTS, perform the Active Test.



Result:
Result Proceed to
C1380 is output A
C1380 is not output B



A

B

4.INSPECT MASTER CYLINDER SOLENOID
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay OFF/ON Stop lights come on


b.
E233300C84
1.427,0.271 1.917,0.563 0.49,0.292 1.688,1.115 1.167,1.677 true 0.188,0.115 0.417,0.281 0.229,0.167 10 false *a 1.542,0.333 1.99,0.594 0.448,0.26 10 false A99 1,1.698 1.448,1.958 0.448,0.26 10 false ACC
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A99-4 (ACC) - Body ground Active Test is on Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - SMART KEY ECU ASSEMBLY)
a.
U148398C03
2.542,1.542 2.771,1.875 false 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.656,1.917 3.063,2.083 0.406,0.167 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the G213 certification ECU (smart key ECU assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-45 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-45 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Result Proceed to
OK A
NG B



A

REPLACE SMART KEY ECU ASSEMBLY

B

6.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - ECM)
6.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - ECM)
a.
U148398C03
2.542,1.542 2.771,1.875 false 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.656,1.917 3.063,2.083 0.406,0.167 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the G56*1, G57*2 or G185*4 ECM connector.

*1: for 1GR-FE

*2: for 1KD-FTV

*4: for 1GD-FTV



c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-45 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-45 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - SHIFT LOCK CONTROL UNIT ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.
U148398C03
2.542,1.542 2.771,1.875 false 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.656,1.917 3.063,2.083 0.406,0.167 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the G150*1 or G45*2 shift lock control ECU (shift lock control unit assembly) connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-45 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-45 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Proceed to
OK
NG (for 1KD-FTV (for Automatic Transmission))
NG (except 1KD-FTV (for Automatic Transmission))



OK

NG (for 1KD-FTV (for Automatic Transmission))

8.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - TCM)

NG (except 1KD-FTV (for Automatic Transmission))

9.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - TCM)
a.
U148398C03
2.542,1.542 2.771,1.875 false 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.656,1.917 3.063,2.083 0.406,0.167 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the G70 TCM connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-45 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-45 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

NG

9.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
a.
U148398C03
2.542,1.542 2.771,1.875 false 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.656,1.917 3.063,2.083 0.406,0.167 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A99 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-45 (STP2) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-45 (STP2) - A99-3 (L) Always Below 1 Ω
A7-45 (STP2) or A99-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A99 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-16 (STPO) - A99-4 (ACC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - REAR COMBINATION LIGHT ASSEMBLY LH)
a.
U148398C01
2.229,0.729 1.688,1.135 true 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.302,0.625 2.708,0.792 0.406,0.167 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the R22 rear combination light assembly LH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-7 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-7 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT ASSEMBLY LH

NG

13.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - REAR COMBINATION LIGHT ASSEMBLY RH)
13.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - REAR COMBINATION LIGHT ASSEMBLY RH)
a.
U148398C01
2.229,0.729 1.688,1.135 true 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.302,0.625 2.708,0.792 0.406,0.167 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the Q31*1 or R21*2 rear combination light assembly RH connector.

*1: for 3 Door

*2: for 5 Door



c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-7 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-7 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT ASSEMBLY RH

NG

14.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - CENTER STOP LIGHT ASSEMBLY)
14.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - CENTER STOP LIGHT ASSEMBLY)
a.
U148398C01
2.229,0.729 1.688,1.135 true 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.302,0.625 2.708,0.792 0.406,0.167 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the Z1 center stop light assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-7 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-7 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

NG

15.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
15.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
a.
U148398C01
2.229,0.729 1.688,1.135 true 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.302,0.625 2.708,0.792 0.406,0.167 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A99 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-7 (STP) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A99-1 (OUT) - A7-7 (STP) Always Below 1 Ω
A99-1 (OUT) or A7-7 (STP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK STOP LIGHT SWITCH ASSEMBLY POWER SOURCE CIRCUIT
a.
E360372C15
1.427,0.333 1.927,0.583 0.5,0.25 1.323,1.188 1.042,1.75 true 2.25,1.188 2.583,1.75 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.552,0.375 2.01,0.531 0.458,0.156 10 false A99 0.844,1.76 1.26,1.958 0.417,0.198 10 false GND 2.552,1.76 2.969,1.958 0.417,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A99 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A99-2 (GND) - Body ground Always Below 1 Ω



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A99-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-16 (STPO) or A99-4 (ACC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR