Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. TABLE OF BOLT, SCREW AND NUT
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.
2. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Disable the AUTO TILT AWAY function by changing the customize parameter.
Click hereSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS
Record the current customize parameter setting (whether the AUTO TILT AWAY function is enabled or disabled) in order to restore the current setting after finishing the operation.
Performing the above operation causes the AUTO TILT AWAY function to be disabled when the engine switch is turned off.
Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.
Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
84140
4.REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY
5.REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
6.REMOVE FRONT SEAT ASSEMBLY RH
for Manual Seat:
Use the same procedure described for the LH side.
for Power Seat:
Use the same procedure described for the LH side.
for Walk in Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Walk in Seat Type)>REMOVAL
58191
7.REMOVE FRONT FLOOR FOOTREST
for LHD:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT FLOOR FOOTREST>REMOVAL
for RHD:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT FLOOR FOOTREST>REMOVAL
58910C
8.REMOVE REAR CONSOLE BOX ASSEMBLY
for Automatic Transmission:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX(for Automatic Transmission)>REMOVAL
for Manual Transmission:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX(for Manual Transmission)>REMOVAL
w/ Refrigerated Cool Box:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX (w/ Refrigerated Cool Box)>REMOVAL
for Bench Seat Type:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX(for Bench Seat Type)>REMOVAL
67920
9.REMOVE DOOR SCUFF PLATE ASSEMBLY LH
67910
10.REMOVE DOOR SCUFF PLATE ASSEMBLY RH
Use the same procedure described for the LH side.
62112
11.REMOVE COWL SIDE TRIM BOARD LH
62111C
12.REMOVE COWL SIDE TRIM BOARD RH
Use the same procedure described for the LH side.
62312B
13.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
14.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
74616C
15.REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH
74615E
16.REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH
Use the same procedure described for the LH side.
74611F
17.REMOVE NO. 1 ASSIST GRIP
62212
18.REMOVE FRONT PILLAR GARNISH LH
62211
19.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
86160J
20.REMOVE FRONT NO. 3 SPEAKER ASSEMBLY
55318C
21.REMOVE INSTRUMENT SIDE PANEL LH
|
Protective Tape |
Put protective tape around the instrument side panel LH.
Using a moulding remover, detach the 5 clips, claw and 3 guides and remove the instrument side panel LH.
55471A
22.REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (for LHD)
|
Protective Tape |
Put protective tape around the instrument cluster finish panel ornament.
Using a moulding remover, detach the 3 clips and remove the instrument cluster finish panel ornament.
55476C
23.REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)
w/ Entry and Start System:
Detach the 4 clips.
Disconnect each connector and remove the instrument panel finish plate garnish.
w/o Entry and Start System:
Detach the 4 clips.
Disconnect each connector and remove the instrument panel finish plate garnish.
55480D
24.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
|
Protective Tape |
Put protective tape around the lower instrument panel finish panel assembly.
Detach the 4 clips.
Disconnect each connector and remove the instrument panel finish panel assembly.
55045
25.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
|
Protective Tape |
Using a screwdriver, detach the 2 claws and open the cover.
Tape the screwdriver tip before use.
w/o Knee Airbag:
Remove the 2 bolts <C>.
Detach the 7 clips.
Disconnect each connector and each cable and remove the lower instrument panel finish panel sub-assembly.
w/ Knee Airbag:
Remove the 2 bolts <C>.
Detach the 14 clips.
Disconnect each connector and each cable and remove the lower instrument panel finish panel sub-assembly.
73900
26.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
55404D
27.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
except 5L-E:
Detach the 4 claws, 2 clips and 2 guides and remove the instrument cluster finish panel sub-assembly.
Disconnect the connector.
for 5L-E:
Detach the 4 claws, 2 clips and 2 guides and remove the instrument cluster finish panel sub-assembly.
Disconnect the connector.
83100
28.REMOVE COMBINATION METER ASSEMBLY
55317A
29.REMOVE INSTRUMENT SIDE PANEL RH
|
Protective Tape |
Put protective tape around the instrument side panel RH.
Using a moulding remover, detach the 5 clips, claw and 3 guides.
Disconnect the connector and remove the instrument side panel RH.
55461A
30.REMOVE INSTRUMENT PANEL ORNAMENT
|
Protective Tape |
Put protective tape around the instrument panel ornament.
Using a moulding remover, detach the 5 clips and remove the instrument panel ornament.
55550
31.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
| *1 | Bolt |
| *2 | Screw |
Remove the 2 bolts <C> and 2 screws <A> or <B>.
Detach the 5 clips and claw.
Disconnect each connector and remove the glove compartment door assembly.
85970A
32.REMOVE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (w/ Telematics Transceiver, Double Door Lock)
86740
33.REMOVE TELEPHONE TRANSCEIVER ASSEMBLY (w/ Telematics Transceiver)
89533
34.REMOVE 4 WHEEL DRIVE CONTROL ECU
55420A
35.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Navigation System)
Detach the 10 clips and remove the center instrument cluster finish panel assembly.
Disconnect each connector.
55522B
36.REMOVE RADIO TUNER OPENING COVER (w/o Audio)
Remove the 4 bolts and radio tuner opening cover.
86120
37.REMOVE RADIO RECEIVER ASSEMBLY (w/ Radio Receiver)
86120L
38.REMOVE NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)
55406B
39.REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Module Switch)
Remove the 2 bolts <E>.
Detach the 3 clips and guide and remove the lower center instrument cluster finish panel sub-assembly.
84970
40.REMOVE COMBINATION SWITCH ASSEMBLY (w/ Module Switch)
55421B
41.REMOVE UPPER INSTRUMENT CLUSTER FINISH PANEL
Detach the 8 clips and 3 guides and remove the upper instrument cluster finish panel.
86160L
42.REMOVE FRONT NO. 4 SPEAKER ASSEMBLY
55650
43.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
Detach the 4 clips and remove the No. 1 instrument panel register assembly.
55660
44.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Use the same procedure described for the No. 1 instrument panel register assembly.
55408F
45.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
|
Protective Tape |
Put protective tape around the No. 1 instrument panel speaker panel sub-assembly.
Using a screwdriver, detach the 2 clips, claw, and 2 guides and remove the No. 1 instrument panel speaker panel sub-assembly.
Tape the screwdriver tip before use.
55409F
46.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Use the same procedure described for the No. 1 instrument panel speaker panel sub-assembly.
86160P
47.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY
55401E
48.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
for LHD:
Partially remove the floor carpet.
It is not necessary to fully remove the floor carpet. Partially remove it so that the No. 2 instrument panel wire can be removed in a later step.
Remove the 6 bolts <E> and nut <F>.
Remove the 2 passenger airbag bolts <G>.
Remove the 4 bolts, 2 nuts and 2 brackets.
Disconnect the connectors and detach the clamps and claws.
Detach the 2 guides and remove the instrument panel safety pad sub-assembly.
| *1 | Bolt <E> | *2 | Nut <F> |
| *3 | Bolt <G> | - | - |
| *a | Bracket | *b | Guide |
for RHD:
Partially remove the floor carpet.
It is not necessary to fully remove the floor carpet. Partially remove it so that the No. 2 instrument panel wire can be removed in a later step.
Remove the 6 bolts <E> and nut <F>.
Remove the 2 passenger airbag bolts <G>.
Remove the 4 bolts, 2 nuts and 2 brackets.
Disconnect the connectors and detach the clamps and claws.
Detach the 2 guides and remove the instrument panel safety pad sub-assembly.
| *1 | Bolt <E> | *2 | Nut <F> |
| *3 | Bolt <G> | - | - |
| *a | Bracket | *b | Guide |