Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › 2017.08–2021.06
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261036 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Collision Door Lock Release Function does not Operate  


DESCRIPTION

When an impact is detected, a relay inside the door control battery is operated to switch the power source of the door lock with motor assemblies from the vehicle battery to the door control battery.

WIRING DIAGRAM

B617341E02
4.927,6.438 6.594,6.823 1.667,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 4.729,4.104 5.802,4.344 1.073,0.24 10 false ACTG 4.958,3.333 6.26,3.583 1.302,0.25 10 false Door Control Battery 4.667,3.167 5.969,3.417 1.302,0.25 10 false A104 4.365,1.438 5.438,1.677 1.073,0.24 10 false ACTG 4.177,1.438 5.25,1.677 1.073,0.24 10 false 9 4.5,4.094 5.573,4.333 1.073,0.24 10 false 3 4.833,6.281 5.906,6.521 1.073,0.24 10 false G216 4.365,0.375 5.438,0.615 1.073,0.24 10 false IG 4.156,0.385 5.229,0.625 1.073,0.24 10 false 8 6.292,4.469 6.667,4.698 0.375,0.229 10 false IC 4.354,2.5 5.656,2.75 1.302,0.25 10 false GND1 4.188,2.5 5.26,2.74 1.073,0.24 10 false 2 4.365,0.833 5.438,1.073 1.073,0.24 10 false BATB 4.365,1.094 5.438,1.333 1.073,0.24 10 false DRLY 2.427,1.167 3.938,1.375 1.51,0.208 10 false to Door Lock Relays 0.135,0.896 1.646,1.104 1.51,0.208 10 false from Battery 4.125,1.094 5.198,1.333 1.073,0.24 10 false 11 4.167,0.833 5.24,1.073 1.073,0.24 10 false 5 0.135,0.375 0.969,0.854 0.833,0.479 10 false from IG NO.1 Relay 1.396,0.615 2.719,0.906 1.323,0.292 10 false ECU-IG NO.2 1.521,1.073 2.458,1.427 0.938,0.354 10 false D/L NO.1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in How to Proceed with Troubleshooting to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

w/ Entry and Start System:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.CHECK DOOR LOCK OPERATION
a.

Check door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

All doors lock and unlock normally.



Result:
Proceed to
OK
NG



OK

2.CHECK DOOR CONTROL BATTERY (BATTERY VOLTAGE)

NG

2.CHECK DOOR CONTROL BATTERY (BATTERY VOLTAGE)
a.
B377768C28
0.323,0.948 0.823,1.281 0.5,0.333 1,1.813 1.427,1.365 true 1.021,0.417 1.458,1.031 true 0.448,1.031 1.063,1.229 0.615,0.198 10 false A104 0.927,1.854 1.302,2.042 0.375,0.188 10 false IG 0.063,0.042 0.438,0.229 0.375,0.188 10 false *a 0.615,0.302 0.99,0.49 0.375,0.188 10 false GND1
*a Front view of wire harness connector
(to Door Control Battery)


Disconnect the door control battery connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A104-8 (IG) - A104-2 (GND1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the A104 door control battery connector.


b.

Disconnect the G216 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A104-9 (ACTG) - G216-3 (ACTG) Always Below 1 Ω
A104-9 (ACTG) or G216-3 (ACTG) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE DOOR CONTROL BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE DOOR CONTROL BATTERY
a.

Replace the door control battery with a new or known good one.



Result:
Proceed to
NEXT



NEXT

5.CHECK DOOR CONTROL BATTERY
5.CHECK DOOR CONTROL BATTERY
a.

Replace the door control battery operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

OK:

Collision detection door lock function operates normally.



Result:
Proceed to
OK
NG



OK

END (DOOR CONTROL BATTERY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)