On the SIGNAL CHECK screen, it is possible to check if the signals sent to the parking assist ECU are normal (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DIAGNOSIS SYSTEM).
On the SIGNAL CHECK screen, "OK" (blue) is displayed for items with a normal inspection result or input state.
On the SIGNAL CHECK screen, "CHK" (red) is displayed for items with an abnormal inspection result or input state.
Displayed items may differ depending on vehicle specifications.
| Item | Signal Input Method | Detail | DTC Output when Abnormal Result is Displayed | Signal Receiver |
|---|---|---|---|---|
|
*1: for Vacuum Brake Booster *2: for Hydraulic Brake Booster |
||||
| CAN | CAN communication | CAN communication signal | DTC is not output | Related ECUs |
| CAM CAN | CAN communication | CAN communication signal | DTC is output | ·
Front television camera assembly ·
Rear television camera assembly ·
Side television camera assembly LH ·
Side television camera assembly RH |
| CAMERA SW | Vehicle wire harness | Panoramic view monitor switch (multi-terrain monitor switch) signal | DTC is not output | Panoramic view monitor switch (multi-terrain monitor switch) |
| SHIFT | CAN communication | Shift information signal | DTC is output | ECM |
| HANDLE | CAN communication | Handle information signal | DTC is output | Main body ECU (multiplex network body ECU) |
| DEST | CAN communication | Destination information signal | DTC is output | Main body ECU (multiplex network body ECU) |
| T/M | CAN communication | Transmisson information signal | DTC is output | ECM |
| VSC | CAN communication | VSC information signal | DTC is output | Brake actuator assembly (skid control ECU)*1
Master cylinder solenoid (skid control ECU)*2 |
| BODY | CAN communication | Body size information signal | DTC is output | Main body ECU (multiplex network body ECU) |
When "!" mark is displayed on the navigation receiver assembly*1 or radio and display receiver assembly*2 after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
(See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION)
*1: for Navigation Receiver Type
*2: for Radio and Display Type
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Inspect the fuses for circuits related to this system before performing the following procedure.
Check which items display on the SIGNAL CHECK screen.
| Result | Proceed to |
|---|---|
| "CAMERA SW" displays "CHK" (red) | A |
| "CAN", "SHIFT", "HANDLE", "DEST", "T/M", "VSC" or "BODY" displays "CHK" (red) | B |
| "CAM CAN" displays "CHK" (red) | C |
A
B
C
Remove the panoramic view monitor switch (multi-terrain monitor switch) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SWITCH>REMOVAL).
Inspect the panoramic view monitor switch (multi-terrain monitor switch) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SWITCH>INSPECTION).
OK
NG
Disconnect the G231 panoramic view monitor switch (multi-terrain monitor switch) connector.
Disconnect the I6 parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G231-5 (ECU) - I6-5 (MPOS) | Always | Below 1 Ω |
| G231-2 (IG) - Body ground | Always | Below 1 Ω |
| G231-5 (ECU) or I6-5 (MPOS) - Body ground | Always | 10 kΩ or higher |
OK
for LHD:
(See pageAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL)
for RHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL
NG