Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260992 NAVIGATION SYSTEM(for Radio and Display Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  B15C0  Short in GPS Antenna  B15C1  Open in GPS Antenna  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly.

DTC Code DTC Detection Condition Trouble Area
B15C0 Navigation antenna error
·

Navigation antenna assembly*1

·

Telephone Antenna Assembly*2

·

Telephone Antenna Cord Sub-assembly*2

·

No. 2 Antenna Cord Sub-assembly*2

·

Antenna Divider*3

·

Navigation ECU

·

Harness or connector


B15C1 Error of the power source to the navigation antenna

*1: w/o Heated Windshield Defroster System

*2: w/ Heated Windshield Defroster System

*3: w/ Heated Windshield Defroster System and w/ Telematics Transceiver


WIRING DIAGRAM

E353358E07
0.135,0.146 3.26,0.375 3.125,0.229 12 false w/o Heated Windshield Defroster System: 1.979,1.625 3.188,2.052 1.208,0.427 10 false Navigation Antenna Assembly 5.25,2.979 7.031,3.385 1.781,0.406 10 false Navigation ECU

E353364E11
2.271,3.156 2.979,3.729 0.708,0.573 10 false Telephone Antenna Assembly 3.292,3.156 4.208,3.729 0.917,0.573 10 false Telephone Antenna Cord Sub-assembly 4.531,3.177 5.448,3.75 0.917,0.573 10 false No. 2 Antenna Cord Sub-assembly 2.583,6.563 3.5,7.135 0.917,0.573 10 false No. 2 Antenna Cord Sub-assembly 1.375,6.563 2.292,7.135 0.917,0.573 10 false Telephone Antenna Cord Sub-assembly 0.354,6.542 1.063,7.115 0.708,0.573 10 false Telephone Antenna Assembly 4.458,6.5 5.51,6.833 1.052,0.333 10 false Antenna Divider 3.073,1.802 3.229,2 0.156,0.198 10 false A 0.146,0.156 3.177,0.385 3.031,0.229 12 false w/ Heated Windshield Defroster System: 0.208,1.271 0.552,1.5 0.344,0.229 10 false *1 0.177,4.5 0.521,4.729 0.344,0.229 10 false *2 3.083,2.5 3.24,2.698 0.156,0.198 10 false A 1.188,5.188 1.344,5.385 0.156,0.198 10 false A 1.188,5.896 1.344,6.094 0.156,0.198 10 false A 4.292,1.813 4.448,2.01 0.156,0.198 10 false B 4.302,2.51 4.458,2.708 0.156,0.198 10 false B 2.385,5.188 2.542,5.385 0.156,0.198 10 false B 2.385,5.896 2.542,6.094 0.156,0.198 10 false B 5.5,1.792 5.771,2 0.271,0.208 10 false C 6.156,8.115 7.156,8.427 1,0.313 10 false Navigation ECU 5.49,2.5 5.76,2.708 0.271,0.208 10 false C 0.104,8.125 2.156,8.365 2.052,0.24 10 false *1: w/o Telematics Transceiver 0.115,8.417 3.031,8.677 2.917,0.26 10 false *2: w/ Telematics Transceiver 3.604,5.188 3.875,5.396 0.271,0.208 10 false C 3.594,5.896 3.865,6.104 0.271,0.208 10 false C 3.021,5.188 3.635,5.385 0.615,0.198 10 false GPS1 6.115,5.198 6.469,5.406 0.354,0.208 10 false D 6.115,2.521 6.469,2.729 0.354,0.208 10 false D 6.125,1.813 6.479,2.021 0.354,0.208 10 false D 4.917,1.813 5.531,2.01 0.615,0.198 10 false GPS1 3.083,1.615 3.24,1.813 0.156,0.198 10 false 2 3.083,2.313 3.292,2.552 0.208,0.24 10 false 2a 4.292,1.615 4.448,1.813 0.156,0.198 10 false 2 4.271,2.302 4.49,2.51 0.219,0.208 10 false 2a 1.167,5.698 1.385,5.906 0.219,0.208 10 false 2a 1.198,5 1.354,5.198 0.156,0.198 10 false 2 2.385,4.99 2.542,5.188 0.156,0.198 10 false 2 2.365,5.688 2.583,5.896 0.219,0.208 10 false 2a 5.5,1.615 5.656,1.813 0.156,0.198 10 false 2 5.469,2.313 5.688,2.531 0.219,0.219 10 false 2a 6.083,2.302 6.302,2.521 0.219,0.219 10 false 1a 6.104,1.604 6.26,1.802 0.156,0.198 10 false 1 3.552,5.698 3.771,5.906 0.219,0.208 10 false 2a 3.594,4.99 3.75,5.188 0.156,0.198 10 false 2 4.26,5.104 4.417,5.302 0.156,0.198 10 false 6 4.219,5.781 4.438,5.99 0.219,0.208 10 false 6a 5.479,5.781 5.698,5.99 0.219,0.208 10 false 2a 5.469,5.094 5.688,5.302 0.219,0.208 10 false 2 6.094,5.698 6.313,5.906 0.219,0.208 10 false 1a 6.104,5 6.323,5.208 0.219,0.208 10 false 1 6.115,5.896 6.469,6.104 0.354,0.208 10 false D 4.458,6.313 4.813,6.521 0.354,0.208 10 false E

PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK DTC
2.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK VEHICLE CONDITION
3.CHECK VEHICLE CONDITION
a.

Check the vehicle condition.


Result:
Result Proceed to
w/o Heated Windshield Defroster System A
w/ Heated Windshield Defroster System B



A

4.CHECK CONNECTION OF NAVIGATION ANTENNA ASSEMBLY

B

6.CHECK VEHICLE CONDITION
4.CHECK CONNECTION OF NAVIGATION ANTENNA ASSEMBLY
a.

Check if the navigation antenna assembly is securely connected to the navigation ECU.

OK:

Navigation antenna assembly is securely connected.



Result:
Proceed to
OK
NG



OK

5.INSPECT NAVIGATION ECU

NG

SECURELY CONNECT NAVIGATION ANTENNA ASSEMBLY

6.CHECK VEHICLE CONDITION
a.

Check the vehicle condition.


Result:
Result Proceed to
w/o Telematics Transceiver A
w/ Telematics Transceiver B



A

7.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY

B

11.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY
7.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the antenna connector from the telephone antenna assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.
E321997C02
1.542,0.156 1.875,0.385 0.333,0.229 1.573,1.74 1.906,1.969 0.333,0.229 1.865,0.844 2.417,0.875 true 0.938,2.5 1.49,2.531 true 1.677,0.198 1.844,0.365 0.167,0.167 10 false A 1.698,1.792 1.865,1.958 0.167,0.167 10 false B 0.188,0.135 0.385,0.292 0.198,0.156 10 false *a 0.24,1.708 0.438,1.865 0.198,0.156 10 false *b 2.469,0.813 2.667,0.969 0.198,0.156 10 false 2a 0.74,2.406 0.938,2.563 0.198,0.156 10 false 2a
*a Front view of wire harness connector
(to Telephone Antenna Assembly)
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-2 Always Below 1 Ω
A-2a - B-2a Always Below 1 Ω
A-2 or B-2 - Body ground Always 10 kΩ or higher
A-2a or B-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

8.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the antenna connector from the telephone antenna cord sub-assembly.


b.

Disconnect the antenna connector from the wire harness.


c.
E350952C12
1.583,0.396 2.021,0.677 0.438,0.281 2.281,1.188 2.802,1.083 true 1.125,3.865 1.583,3.677 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.75,0.458 1.906,0.656 0.156,0.198 10 false B 2.865,1 3.063,1.198 0.198,0.198 10 false 2a 0.927,3.781 1.125,3.979 0.198,0.198 10 false 2a 0.177,2.563 0.49,2.76 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Telephone Antenna Cord Sub-assembly)
*a Front view of wire harness connector
(to Wire Harness)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - 2 Always Below 1 Ω
B-2a - 2a Always Below 1 Ω
B-2 - Body ground Always 10 kΩ or higher
B-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - TELEMATICS TRANSCEIVER [DATA COMMUNICATION MODULE (DCM)])

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - TELEMATICS TRANSCEIVER [DATA COMMUNICATION MODULE (DCM)])
a.
E353379C03
1.583,0.302 1.99,0.573 0.406,0.271 1.604,2.635 2.01,2.906 0.406,0.271 1.969,3.823 2.458,4.094 true 2.281,1.198 2.5,1.417 true 1.74,0.354 2.198,0.552 0.458,0.198 10 false C 1.771,2.688 2.229,2.885 0.458,0.198 10 false D 2.5,4.031 3.115,4.229 0.615,0.198 10 false 1a 2.552,1.385 3.167,1.583 0.615,0.198 10 false 2a 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.25,2.573 0.563,2.771 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to navigation ECU)


Disconnect the No. 2 antenna cord sub-assembly connector.


b.

Disconnect the navigation ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-2 - D-1 Always Below 1 Ω
C-2a - D-1a Always Below 1 Ω
C-2 - Body ground Always 10 kΩ or higher
C-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK TELEPHONE ANTENNA ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK TELEPHONE ANTENNA ASSEMBLY

OK

END (TELEPHONE ANTENNA ASSEMBLY IS DEFECTIVE)

NG

11.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY
a.
E350951C19
1.646,0.271 2.042,0.552 0.396,0.281 1.677,2.563 2.073,2.844 0.396,0.281 1.26,1.313 1.677,1.271 true 1.063,3.417 1.594,3.583 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.083,1.219 1.396,1.417 0.313,0.198 10 false 2a 0.865,3.323 1.177,3.521 0.313,0.198 10 false 2a 1.792,0.333 1.948,0.531 0.156,0.198 10 false A 1.823,2.625 1.979,2.823 0.156,0.198 10 false B 0.208,2.656 0.521,2.854 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Telephone Antenna Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the telephone antenna assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-2 Always Below 1 Ω
A-2a - B-2a Always Below 1 Ω
A-2 or B-2 - Body ground Always 10 kΩ or higher
A-2a or B-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

12.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the antenna connector from the telephone antenna cord sub-assembly.


b.

Disconnect the antenna connector from the wire harness.


c.
E350952C13
1.583,0.396 2.021,0.677 0.438,0.281 2.281,1.188 2.802,1.083 true 1.104,3.885 1.583,3.656 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.75,0.458 1.906,0.656 0.156,0.198 10 false B 2.865,1 3.063,1.198 0.198,0.198 10 false 2a 0.906,3.792 1.104,3.99 0.198,0.198 10 false 2a 0.177,2.563 0.49,2.76 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Telephone Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Wire Harness)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - 2 Always Below 1 Ω
B-2a - 2a Always Below 1 Ω
B-2 - Body ground Always 10 kΩ or higher
B-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - ANTENNA DIVIDER)

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - ANTENNA DIVIDER)
a.
E350976C13
1.583,0.354 2.021,0.656 0.438,0.302 1.583,2.563 2.021,2.865 0.438,0.302 2.271,1.208 2.469,1.302 true 2.792,3.635 2.927,3.979 true 1.74,0.417 2.042,0.646 0.302,0.229 10 false C 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 1.74,2.635 2.083,2.854 0.344,0.219 10 false E 2.5,1.219 2.74,1.427 0.24,0.208 10 false 2a 2.938,3.979 3.177,4.188 0.24,0.208 10 false 6a 0.208,2.51 0.521,2.708 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Divider)


Disconnect the No. 2 antenna cord sub-assembly connector.


b.

Disconnect the antenna divider connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-2 - E-6 Always Below 1 Ω
C-2a - E-6a Always Below 1 Ω
C-2 - Body ground Always 10 kΩ or higher
C-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.INSPECT ANTENNA DIVIDER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT ANTENNA DIVIDER
a.

b.
E241596C16
1.125,1.417 0.979,1.76 0.979,1.76 0.781,1.76 true 1.979,1.406 1.833,1.75 1.833,1.75 1.635,1.75 true 0.573,1.677 1,1.854 0.427,0.177 10 false 6a 1.438,1.656 1.865,1.833 0.427,0.177 10 false 2a 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Divider)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 - 2 Always 10 kΩ or higher
2 - 2a Always 243 to 267 Ω
6 - 6a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (ANTENNA DIVIDER - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)

NG

15.CHECK HARNESS AND CONNECTOR (ANTENNA DIVIDER - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)
a.

Disconnect the antenna divider connector.


b.

Disconnect the multi-media module receiver assembly connector.


c.
E353380C03
1.542,0.375 1.948,0.667 0.406,0.292 1.594,2.469 2,2.76 0.406,0.292 0.948,2.031 1.26,1.594 true 1.365,4.302 1.677,3.865 true 1.688,0.438 2.302,0.635 0.615,0.198 10 false E 1.729,2.531 2.344,2.729 0.615,0.198 10 false D 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 0.229,2.458 0.542,2.656 0.313,0.198 10 false *b 0.76,2 1.073,2.198 0.313,0.198 10 false 2a 1.167,4.25 1.479,4.448 0.313,0.198 10 false 1a
*a Front view of wire harness connector
(to Antenna Divider)
*a Front view of wire harness connector
(to Multi-media Module Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-2 - D-1 Always Below 1 Ω
E-2a - D-1a Always Below 1 Ω
E-2 or D-1 - Body ground Always 10 kΩ or higher
E-2a or D-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK TELEPHONE ANTENNA ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK TELEPHONE ANTENNA ASSEMBLY
a.

b.

Clear the DTCs.

Click here


c.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE ANTENNA ASSEMBLY IS DEFECTIVE)

NG

17.CHECK ANTENNA DIVIDER
17.CHECK ANTENNA DIVIDER

OK

END (ANTENNA DIVIDER IS DEFECTIVE)

NG