Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260992 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the headlight dimmer switch is in the tail or head position.

WIRING DIAGRAM

E377085E04
1.354,0.521 2.406,0.76 1.052,0.24 10 false from TAIL Relay 3.313,0.688 3.875,0.885 0.563,0.198 10 false PANEL 6.167,3.031 6.563,3.229 0.396,0.198 10 false ILL+ 6.156,6.042 6.656,6.271 0.5,0.229 10 false GND1 6.146,5.083 6.625,5.281 0.479,0.198 10 false SWG 5.76,3.021 6.24,3.219 0.479,0.198 10 false H49 5.802,2.813 6.281,3.01 0.479,0.198 10 false 10 5.76,5.083 6.24,5.281 0.479,0.198 10 false H51 5.813,4.844 6.292,5.042 0.479,0.198 10 false 23 5.76,6.031 6.24,6.229 0.479,0.198 10 false H49 5.823,5.792 6.302,5.99 0.479,0.198 10 false 7 5.885,6.615 7.156,6.99 1.271,0.375 10 false Radio and Display Receiver Assembly 4.094,3.021 4.656,3.219 0.563,0.198 10 false G208 4.198,2.792 4.76,2.99 0.563,0.198 10 false 13 4.094,5.083 4.656,5.281 0.563,0.198 10 false G208 4.25,4.875 4.813,5.073 0.563,0.198 10 false 3 2.813,3.021 3.375,3.219 0.563,0.198 10 false z16 2.844,5.094 3.406,5.292 0.563,0.198 10 false z16 2.917,4.896 3.104,5.083 0.188,0.188 10 false 8 2.885,2.813 3.073,3 0.188,0.188 10 false 5 3.448,2.875 3.844,3.073 0.396,0.198 10 false IL+2 3.469,4.969 3.865,5.167 0.396,0.198 10 false EAU 3.104,5.927 4.177,6.417 1.073,0.49 10 false Spiral Cable Sub-assembly 0.406,6.635 2.51,7.125 2.104,0.49 10 false Steering Pad Switch Assembly 0.969,6.156 1.813,6.375 0.844,0.219 10 false for RH Side 1,3.729 1.844,3.948 0.844,0.219 10 false for LH Side

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

Inspect the fuse for circuits related to this system before performing the following inspection procedure.



HINT:

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio and display receiver assembly, steering pad switch assembly or others (hazard switch etc.) comes on when the headlight dimmer switch is turned to the head or tail position.

Result
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio and display receiver assembly. B
No illumination comes on (radio and display receiver assembly, steering pad switch, hazard switch, heater control switch, etc.). C



A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.
U166423E02
2.583,1.823 2.396,1.823 2.396,1.823 2.063,1.51 true 0.083,0.042 0.396,0.24 0.313,0.198 10 false *a 1.51,0.219 1.948,0.417 0.438,0.198 10 false G208 2.625,1.698 3.24,1.896 0.615,0.198 10 false IL+2

Disconnect the spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G208-13 (IL+2) - Body ground Light control switch in the tail or head position 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>REMOVAL).


b.

Inspect the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>INSPECTION).



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Inspect the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)
a.

Disconnect the H49 and H51 radio and display receiver assembly connectors.


b.

Disconnect the G208 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H51-23 (SWG) - G208-3 (EAU) Always Below 1 Ω
H49-7 (GND1) - Body ground Always Below 1 Ω
H51-23 (SWG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U149444E01
1.513,0.252 1.807,0.436 0.294,0.184 10 H49 0.05,0 0.343,0.184 0.293,0.184 10 *a 2.785,1.725 3.150,1.909 0.366,0.184 10 ILL+ 0.618,1.725 1.033,1.909 0.415,0.184 10 GND1 2.321,1.4 2.496,1.818 2.496,1.818 2.762,1.818 false 1.569,1.4 1.395,1.818 1.395,1.818 1.129,1.818 false

Disconnect the radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H49-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H49-10 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR