Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (for Halogen Headlight) › 2017.08–2020.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0326211 LIGHTING SYSTEM(for Halogen Headlight) J

LIGHTING (EXT)  LIGHTING SYSTEM(for Halogen Headlight)  Automatic High Beam System does not Operate or Operation Indicator does not Illuminate  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the automatic high beam system based on signals received from the forward recognition camera.

WIRING DIAGRAM

E378102E01
2.875,3.927 4.865,4.26 1.99,0.333 10 false Forward Recognition Camera 0.854,4.417 2.844,4.75 1.99,0.333 10 false : CAN Communication Line 0.396,2.646 2.948,3.031 2.552,0.385 10 false Combination Meter Assembly (Automatic High Beam Indicator Light) 3.708,0.573 4.26,0.948 0.552,0.375 10 false +B 4,0.563 4.552,0.938 0.552,0.375 10 false 5 2.781,0.552 3.333,0.927 0.552,0.375 10 false 2 2.99,0.573 3.542,0.948 0.552,0.375 10 false E 2.833,1.073 4.667,1.448 1.833,0.375 10 false G222 5.74,0.635 6.292,1.01 0.552,0.375 10 false AHBI 5.458,0.563 6.01,0.938 0.552,0.375 10 false 23 5.333,2.813 7.01,3.177 1.677,0.365 10 false G216 5.344,2.979 7.021,3.344 1.677,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 2.813,1.25 4.646,1.625 1.833,0.375 10 false Auto High Beam Switch

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



PROCEDURE

1.CHECK AUTOMATIC HIGH BEAM INDICATOR LIGHT
a.

Check the operation of the automatic high beam indicator light.

·

Turn the ignition switch to ON.

·

Turn the light control switch to the Auto or Head position.

·

Turn the headlight dimmer switch to the High position.

·

Turn the auto high beam switch on.


OK:

Automatic high beam indicator light illuminate.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

4.READ VALUE USING GTS
2.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>DATA LIST / ACTIVE TEST

i.
E367861C01
0.427,0.74 0.625,0.74 0.625,0.74 0.927,0.906 true 2.167,1.281 2.5,1.833 2.5,1.833 2.74,1.833 true 0.25,0.667 0.563,0.865 0.313,0.198 10 false *2 2.792,1.74 3.104,1.938 0.313,0.198 10 false *1 1.49,1.198 1.802,1.396 0.313,0.198 10 false *a
*1 Forward Recognition Camera (Automatic High Beam Sensor)
*2 Work Light or Equivalent
*a 100 mm (3.94 in.) or less


Shine a light on the automatic high beam sensor*.

HINT:

*: If troubleshooting is being performed in a bright area, such as outside on a sunny day, it will not be necessary to perform this step.


Main Body
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Auto H Beam STS0 Automatic high beam sensor state past 0 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed -

OK:

The Data List value displays "Daytime".




Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS

NG

REPLACE FORWARD RECOGNITION CAMERA

3.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>DATA LIST / ACTIVE TEST

i.
E367862C01
1.667,1.229 1.917,1.771 1.917,1.771 2.094,1.771 true 1,0.854 1.313,1.052 0.313,0.198 10 false *a 0.969,1.51 1.281,1.708 0.313,0.198 10 false *a 2.365,0.875 2.677,1.073 0.313,0.198 10 false *b 2.146,1.688 2.458,1.885 0.313,0.198 10 false *1
*1 Cardboard or Equivalent Object
*a 150 mm (5.91 in.) or higher
*b 3 mm (0.118 in.) or higher


Cover the automatic high beam sensor with an opaque object, such as cardboard.

NOTICE:
·

Make sure that there is no clearance between the cardboard or equivalent object and the area of the windshield glass in front of the automatic high beam sensor.

·

If there is any clearance, light may shine on the automatic high beam sensor and the value of the Data List will not change.



Main Body
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Auto H Beam STS0 Automatic high beam sensor state past 0 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed -

OK:

The Data List value displays "Speed".




Result:
Proceed to
OK
NG



OK

NG

REPLACE FORWARD RECOGNITION CAMERA

4.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>DATA LIST / ACTIVE TEST

Main Body
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Auto High Beam Main Switch Auto high beam switch signal / OFF or ON OFF: Auto high beam switch off
ON: Auto high beam switch on
-

OK:

Normal condition listed above is displayed.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS

NG

7.INSPECT AUTO HIGH BEAM SWITCH
5.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>DATA LIST / ACTIVE TEST

Main Body
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Auto H Beam STS0 Automatic high beam sensor state past 0 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed -

OK:

The Data List value displays "Daytime" or "Speed".



Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS

NG

REPLACE FORWARD RECOGNITION CAMERA

6.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>DATA LIST / ACTIVE TEST

Combination Meter
Tester Display Measurement Item Control Range Diagnostic Note
Automatic High Beam Indicator Automatic high beam indicator light OFF or ON -

OK:

Automatic high beam indicator light illuminate.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE COMBINATION METER ASSEMBLY

7.INSPECT AUTO HIGH BEAM SWITCH
a.

Remove the auto high beam main switch.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HIGH BEAM MAIN SWITCH>REMOVAL


b.

Inspect the auto high beam main switch.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HIGH BEAM MAIN SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

8.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the G222 auto high beam switch connector.


b.

Disconnect the G216 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G222-5 (+B) - G216-23 (AHBI) Always Below 1 Ω
G222-2 (E) - Body ground Always Below 1 Ω
G222-5 (+B) or G216-23 (AHBI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR