Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type) › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260991 NAVIGATION SYSTEM(for Navigation Receiver Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  B157D  DAB Tuner Antenna Disconnected  


DESCRIPTION

This DTC is stored when a malfunction occurs in the digital audio broadcasting antenna assembly which is connected to the navigation receiver assembly.

DTC Code DTC Detection Condition Trouble Area
B157D The digital audio broadcasting antenna assembly is not connected
·

Digital audio broadcasting antenna assembly

·

No. 2 antenna cord sub-assembly

·

Windshield glass (window glass antenna wire)

·

Harness or connector

·

Navigation receiver assembly



WIRING DIAGRAM

E377442E02
0.198,0.094 4.188,0.323 3.99,0.229 10 false Windshield Glass (Window Glass Antenna Wire) 1.104,2.344 1.948,3.063 0.844,0.719 10 false Digital Audio Broadcasting Antenna Assembly 2.302,2.344 3.542,2.698 1.24,0.354 10 false No. 2 Antenna Cord Sub-assembly 5.25,2.406 5.563,2.604 0.313,0.198 10 false DB 5.25,2.594 6.458,2.969 1.208,0.375 10 false Navigation Receiver Assembly 2.281,1.229 2.438,1.427 0.156,0.198 10 false 1 3.177,1.219 3.333,1.417 0.156,0.198 10 false 1 4.188,1.219 4.344,1.417 0.156,0.198 10 false 1 4.792,1.219 4.948,1.417 0.156,0.198 10 false 1 2.281,1.5 2.74,1.698 0.458,0.198 10 false 1-a 3.073,1.5 3.531,1.698 0.458,0.198 10 false 1-a 4.167,1.5 4.625,1.698 0.458,0.198 10 false 1-a 4.729,1.5 5.188,1.698 0.458,0.198 10 false 1-a

CAUTION / NOTICE / HINT

HINT:

When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

OK:

Optional components are installed.


NOTICE:

Do not remove optional components without permission of the customer.




OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

NG

3.INSPECT WINDSHIELD GLASS (WINDOW GLASS ANTENNA WIRE)
3.INSPECT WINDSHIELD GLASS (WINDOW GLASS ANTENNA WIRE)
a.

Inspect the windshield glass (window glass antenna wire) (See page Audio / Visual / Telematics>AUDIO / VIDEO>WINDOW GLASS ANTENNA WIRE>REPAIR).



OK

4.CHECK NAVIGATION RECEIVER ASSEMBLY

NG

4.CHECK NAVIGATION RECEIVER ASSEMBLY
a.

Remove the antenna connector from the navigation receiver assembly.


b.

Turn the engine switch on (ACC) with the navigation receiver assembly connector connected.


c.

Turn on the radio and turn into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise occurs.




OK

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 2 ANTENNA CORD SUB-ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 2 ANTENNA CORD SUB-ASSEMBLY)
a.
E376793C01
1.583,0.156 1.917,0.417 0.333,0.26 1.927,1.219 2.458,1.813 2.458,1.813 2.635,1.813 true 1.927,2.906 2.479,2.552 2.479,2.552 2.656,2.552 true 0.281,0.323 0.594,0.521 0.313,0.198 10 false *a 0.344,2.115 0.656,2.313 0.313,0.198 10 false *b 2.667,1.729 2.979,1.927 0.313,0.198 10 false 1a 2.719,2.458 3.031,2.656 0.313,0.198 10 false 1a 1.667,0.198 1.979,0.396 0.313,0.198 10 false DB
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the DB navigation receiver assembly connector.


b.

Disconnect the antenna connector from the No.2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DB-1 - 1 Always Below 1 Ω
DB-1-a - 1-a Always Below 1 Ω
DB-1 - Body ground Always 10 kΩ or higher
DB-1-a - Body ground Always 10 kΩ or higher




OK

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E286153C01
1.833,1.094 2.427,0.563 2.427,0.563 2.635,0.563 true 1.802,2.552 2.396,2.021 2.396,2.021 2.604,2.021 true 2.708,0.479 3.167,0.677 0.458,0.198 10 false 1-a 2.688,1.917 3.146,2.115 0.458,0.198 10 false 1-a 0.125,0.125 0.583,0.323 0.458,0.198 10 false *a 0.188,1.75 0.646,1.948 0.458,0.198 10 false *b
*a Front view of wire harness connector
(to Digital Audio Broadcasting Antenna Assembly)
*b Front view of wire harness connector
(to Wire Harness)


Disconnect the antenna connector from the digital audio broadcasting antenna assembly.


b.

Disconnect the antenna connector from the no. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 1 Always Below 1 Ω
1-a - 1-a Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
1-a - Body ground Always 10 kΩ or higher




OK

7.CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

7.CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY

OK

END (DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY IS DEFECTIVE)

NG