Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, current flows from terminal ST1 of the ignition switch to the starter relay coil and current also flows to terminal STA of the ECM (STA signal).

When the STA signal and NE signal are input to the ECM, Tr is turned on, current flows to the coil of the circuit opening relay, the relay switches on, power is supplied to the fuel pump and the fuel pump operates.

While the NE signal is generated (engine running), the ECM keeps Tr on (circuit opening relay on) and the fuel pump continues operating.

WIRING DIAGRAM

A413219E01
6,0.417 6.615,0.615 0.615,0.198 10 false IG1D 5.802,0.323 5.958,0.521 0.156,0.198 10 false 3 5.813,0.865 6.427,1.063 0.615,0.198 10 false G213 5.833,1.063 6.896,1.594 1.063,0.531 10 false Certification ECU (Smart Key ECU Assembly) 5.302,0.333 5.615,0.531 0.313,0.198 10 false *3 3.938,0.615 5.313,0.813 1.375,0.198 10 false IG2 NO. 2 4.51,0.323 4.823,0.521 0.313,0.198 10 false *4 3.021,0.427 3.479,0.625 0.458,0.198 10 false IG2 2.406,0.438 2.865,0.635 0.458,0.198 10 false AM2 2.292,0.854 2.75,1.052 0.458,0.198 10 false G2 2.292,1.042 6.271,1.24 3.979,0.198 10 false Ignition Switch Assembly*4 1.302,0.615 1.615,0.813 0.313,0.198 10 false ST 0.5,1.042 1.573,1.24 1.073,0.198 10 false 250A FL 4.104,2.406 4.417,2.604 0.313,0.198 10 false 1V 4.188,2.219 4.344,2.417 0.156,0.198 10 false 2 4.104,1.958 4.417,2.156 0.313,0.198 10 false 1V 4.167,1.74 4.323,1.938 0.156,0.198 10 false 1 2.292,2.125 2.75,2.323 0.458,0.198 10 false IG2 1.385,1.958 1.698,2.156 0.313,0.198 10 false 1S 1.406,1.74 1.563,1.938 0.156,0.198 10 false 1 0.635,2.125 1.552,2.323 0.917,0.198 10 false 70A FL 3.104,2.656 3.563,2.854 0.458,0.198 10 false IG2 1.875,3.281 4.021,3.479 2.146,0.198 10 false EFI MAIN NO. 1 2.75,3.854 4.896,4.052 2.146,0.198 10 false EFI MAIN NO. 1 1.365,3.573 1.677,3.771 0.313,0.198 10 false 1W 1.427,3.365 1.583,3.563 0.156,0.198 10 false 4 4.073,3.563 4.385,3.76 0.313,0.198 10 false 1W 4.177,3.333 4.333,3.531 0.156,0.198 10 false 8 5.667,3.563 6.281,3.76 0.615,0.198 10 false G181 5.823,3.354 5.979,3.552 0.156,0.198 10 false 6 6.083,3.542 6.698,3.74 0.615,0.198 10 false MREL 1.375,4.646 1.688,4.844 0.313,0.198 10 false 1V 1.385,4.427 1.542,4.625 0.156,0.198 10 false 6 2.979,5.292 3.75,5.49 0.771,0.198 10 false C/OPN 4.542,5.177 5.917,5.375 1.375,0.198 10 false IGN NO. 2 4.083,5.042 4.396,5.24 0.313,0.198 10 false 1W 4.135,4.833 4.448,5.031 0.313,0.198 10 false 12 2.49,5.552 2.802,5.75 0.313,0.198 10 false 1V 2.25,5.542 2.406,5.74 0.156,0.198 10 false 7 5.656,5.896 6.271,6.094 0.615,0.198 10 false G181 5.792,5.677 5.948,5.875 0.156,0.198 10 false 5 6.104,5.719 6.417,5.917 0.313,0.198 10 false FC 6.083,6.615 6.542,6.813 0.458,0.198 10 false STA 5.656,6.635 6.271,6.833 0.615,0.198 10 false C154 5.656,7.177 6.271,7.375 0.615,0.198 10 false C153 5.677,7.729 6.292,7.927 0.615,0.198 10 false C153 6.083,7.167 6.542,7.365 0.458,0.198 10 false NE+ 6.104,7.719 6.563,7.917 0.458,0.198 10 false NE- 3.917,6.615 6.979,6.813 3.063,0.198 10 false from Starter Circuit 3.646,7.354 5.188,7.719 1.542,0.365 10 false from Crankshaft Position Sensor Circuit 1.146,6.458 2.219,6.656 1.073,0.198 10 false 4*1 1.146,6.635 1.604,6.833 0.458,0.198 10 false 1*2 2.115,6.458 3.188,6.656 1.073,0.198 10 false 5*1 2.125,6.625 2.583,6.823 0.458,0.198 10 false 2*2 1.333,7.417 1.948,7.615 0.615,0.198 10 false S5*1 1.677,7.417 2.448,7.615 0.771,0.198 10 false R38*2 1.375,7.583 2.75,7.781 1.375,0.198 10 false Fuel Pump 0.635,7.74 1.708,7.938 1.073,0.198 10 false Battery 1.479,7.885 3.625,8.083 2.146,0.198 10 false *1: for 5 Door 1.458,8.208 3.604,8.406 2.146,0.198 10 false *2: for 3 Door 2.583,7.927 7.021,8.125 4.438,0.198 10 false *3: w/ Entry and Start System 2.583,8.24 4.781,8.469 2.198,0.229 10 false *4: w/o Entry and Start System 1.104,5.75 2.583,5.99 1.479,0.24 10 false No.1 Integration Relay 0.688,0.344 1,0.542 0.313,0.198 10 false *4 5.76,6.427 6.073,6.625 0.313,0.198 10 false 17 5.781,6.99 6.094,7.188 0.313,0.198 10 false 27 5.781,7.531 6.094,7.729 0.313,0.198 10 false 34

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (OPERATE C/OPN RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


e.

Check whether the fuel pump operation sound occurs when performing the Active Test on the tester.

OK:

Fuel pump operating sound occurs.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT NO. 1 INTEGRATION RELAY (C/OPN RELAY)
2.INSPECT NO. 1 INTEGRATION RELAY (C/OPN RELAY)
a.

Inspect the No. 1 integration relay (C/OPN relay) (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPLACE CIRCUIT OPENING RELAY (C/OPN)

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Disconnect the ECM connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1V-7 - G181-5 (FC) Always Below 1 Ω
1V-7 or G181-5 (FC) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (C/OPN RELAY) - NO. 1 INTEGRATION RELAY (IG2 RELAY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (C/OPN RELAY - ECM)

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (C/OPN RELAY) - NO. 1 INTEGRATION RELAY (IG2 RELAY))
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1V-1 - 1W-12 Always Below 1 Ω
1V-1 or 1W-12 - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (C/OPN RELAY - NO. 1 INTEGRATION RELAY (EFI MAIN RELAY, IG2 RELAY))

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP)
a.

Disconnect the fuel pump connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 5 Door
Tester Connection Condition Specified Condition
1V-6 - S5-4 Always Below 1 Ω
1V-6 or S5-4 - Body ground Always 10 kΩ or higher

for 3 Door
Tester Connection Condition Specified Condition
1V-6 - R38-1 Always Below 1 Ω
1V-6 or R38-1 - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (C/OPN RELAY - FUEL PUMP)

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)
a.

Disconnect the fuel pump connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 5 Door
Tester Connection Condition Specified Condition
S5-5 - Body ground Always Below 1 Ω

for 3 Door
Tester Connection Condition Specified Condition
R38-2 - Body ground Always Below 1 Ω




OK

7.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PUMP - BODY GROUND)

7.INSPECT FUEL PUMP
a.

Inspect the fuel pump.



Result:
Result Proceed to
OK A
NG (for 5 Door) B
NG (for 3 Door) C



A

B

C