Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P064C  Glow Plug Control Module  P066B  Cylinder 1 Glow Plug Control Circuit High  P066D  Cylinder 2 Glow Plug Control Circuit High  P066F  Cylinder 3 Glow Plug Control Circuit High  P0671  Cylinder 1 Glow Plug Circuit/Open  P0672  Cylinder 2 Glow Plug Circuit/Open  P0673  Cylinder 3 Glow Plug Circuit/Open  P0674  Cylinder 4 Glow Plug Circuit/Open  P067B  Cylinder 4 Glow Plug Control Circuit High  P166F  Glow Plug Control Module Circuit Short  


DESCRIPTION

P064C
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Enter check mode The MOS inside the glow plug control unit is detected as being stuck on 3 times while the glow plugs are on (2 trip detection logic). Glow plug controller

P066B
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Enter check mode A short circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 1 glow plug assembly

·

Short in No. 1 glow plug circuit



P066D
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Enter check mode A short circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 2 glow plug assembly

·

Short in No. 2 glow plug circuit



P066F
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Enter check mode A short circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 3 glow plug assembly

·

Short in No. 3 glow plug circuit



P067B
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Enter check mode A short circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 4 glow plug assembly

·

Short in No. 4 glow plug circuit



P0671
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Enter check mode An open circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 1 glow plug assembly

·

Open in No. 1 glow plug circuit



P0672
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Enter check mode An open circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 2 glow plug assembly

·

Open in No. 2 glow plug circuit



P0673
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Enter check mode An open circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 3 glow plug assembly

·

Open in No. 3 glow plug circuit



P0674
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Enter check mode An open circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 4 glow plug assembly

·

Open in No. 4 glow plug circuit



P166F
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Enter check mode A short circuit in a wire harness between the glow plugs is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

Open or short in glow plug circuit



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
DTC P0671, P0672, P0673 and/or P0674 is output A
DTC P066B, P066D, P066F and/or P067B is output B
DTC P064C and/or P166F is output C



A

2.CHECK GLOW PLUG CONTROLLER

B

8.CHECK HARNESS AND CONNECTOR

C

13.CHECK HARNESS AND CONNECTOR
2.CHECK GLOW PLUG CONTROLLER
a.
U169373E02
1.781,1.26 2.125,1.771 true 0.135,0.167 0.323,0.344 0.188,0.177 10 false *a 2.146,1.688 2.531,1.865 0.385,0.177 10 false BATT 0.656,1.073 0.979,1.229 0.323,0.156 10 false A80

Disconnect the glow plug controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A80-1(BATT) - Body ground Engine Switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Glow Plug Controller)


c.

Reconnect the glow plug controller connector.



OK

3.CHECK HARNESS AND CONNECTOR

NG

17.INSPECT GLOW RELAY
3.CHECK HARNESS AND CONNECTOR
a.

Disconnect connectors of the glow plug controller.

U169489E01
1.146,2.552 1.5,2.198 false 1.5,2.198 1.615,2.198 false 1.729,1.24 2.083,0.896 false 2.083,0.896 2.198,0.896 false 1.448,1.906 1.802,1.563 false 1.802,1.563 1.917,1.563 false 2.01,0.573 2.365,0.229 false 2.365,0.229 2.479,0.229 false 3.458,1.5 3.156,2.083 false 3.771,1.49 3.99,2.073 false 5.698,1.5 5.396,2.083 false 6.01,1.49 6.229,2.083 false 0.792,0.292 0.99,0.458 0.198,0.167 10 false *1 1.656,2.146 1.865,2.313 0.208,0.167 10 false 1 1.969,1.49 2.177,1.656 0.208,0.167 10 false 2 2.51,0.156 2.719,0.323 0.208,0.167 10 false 4 2.229,0.833 2.438,1 0.208,0.167 10 false 3 5.365,0.563 5.563,0.729 0.198,0.167 10 false *b 3.094,0.563 3.292,0.729 0.198,0.167 10 false *a 3.01,2.125 3.396,2.292 0.385,0.167 10 false GL1 3.906,2.125 4.292,2.292 0.385,0.167 10 false GL2 6.135,2.125 6.521,2.292 0.385,0.167 10 false GL4 5.229,2.125 5.615,2.292 0.385,0.167 10 false GL3 2.677,1.271 2.979,1.427 0.302,0.156 10 false A82 4.969,1.323 5.271,1.479 0.302,0.156 10 false A92


b.

Remove the No. 1 glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A82-1 (GL1) - No. 1 glow plug connector terminal 1 Always Below 1 Ω
A82-2 (GL2) - No. 1 glow plug connector terminal 2 Always Below 1 Ω
A92-1 (GL3) - No. 1 glow plug connector terminal 3 Always Below 1 Ω
A92-2 (GL4) - No. 1 glow plug connector terminal 4 Always Below 1 Ω


Text in Illustration
*1 No. 1 Glow Plug Connector - -
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)


d.

Reconnect the glow plug controller connector.


e.

Reinstall the No. 1 glow plug connector.



OK

4.INSPECT GLOW PLUG ASSEMBLY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.INSPECT GLOW PLUG ASSEMBLY

b.

Exchange the glow plugs of the malfunctioning cylinders (the cylinders indicated by output DTCs) with the glow plugs of normally functioning cylinders.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Using the GTS, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>CHECK MODE PROCEDURE).


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
Same DTCs (that have been erased) A
Other DTCs B

HINT:

Check for DTCs in check mode.




B

5.REPLACE GLOW PLUG ASSEMBLY

A

14.REPLACE GLOW PLUG CONTROLLER
5.REPLACE GLOW PLUG ASSEMBLY
a.

Replace the glow plug assembly (See page Engine / Hybrid System>1GD-FTV (STARTING)>GLOW PLUG>REMOVAL).



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>CHECK MODE PROCEDURE).


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.

HINT:

Check for DTCs in check mode.




NEXT

END

8.CHECK HARNESS AND CONNECTOR
a.

Disconnect connectors of the glow plug controller.

U169489E01
1.146,2.552 1.5,2.198 false 1.5,2.198 1.615,2.198 false 1.729,1.24 2.083,0.896 false 2.083,0.896 2.198,0.896 false 1.448,1.906 1.802,1.563 false 1.802,1.563 1.917,1.563 false 2.01,0.573 2.365,0.229 false 2.365,0.229 2.479,0.229 false 3.458,1.5 3.156,2.083 false 3.771,1.49 3.99,2.073 false 5.698,1.5 5.396,2.083 false 6.01,1.49 6.229,2.083 false 0.792,0.292 0.99,0.458 0.198,0.167 10 false *1 1.656,2.146 1.865,2.313 0.208,0.167 10 false 1 1.969,1.49 2.177,1.656 0.208,0.167 10 false 2 2.51,0.156 2.719,0.323 0.208,0.167 10 false 4 2.229,0.833 2.438,1 0.208,0.167 10 false 3 5.365,0.563 5.563,0.729 0.198,0.167 10 false *b 3.094,0.563 3.292,0.729 0.198,0.167 10 false *a 3.01,2.125 3.396,2.292 0.385,0.167 10 false GL1 3.906,2.125 4.292,2.292 0.385,0.167 10 false GL2 6.135,2.125 6.521,2.292 0.385,0.167 10 false GL4 5.229,2.125 5.615,2.292 0.385,0.167 10 false GL3 2.677,1.271 2.979,1.427 0.302,0.156 10 false A82 4.969,1.323 5.271,1.479 0.302,0.156 10 false A92


b.

Remove the No. 1 glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A82-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground Always Below 1 Ω
A82-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground Always Below 1 Ω
A92-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground Always Below 1 Ω
A92-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground Always Below 1 Ω


Text in Illustration
*1 No. 1 Glow Plug Connector - -
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)

HINT:

Make sure that there are no short circuits to the battery.



d.

Reconnect the glow plug controller connector.


e.

Reinstall the No. 1 glow plug connector.



OK

9.REPLACE GLOW PLUG CONTROLLER

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPLACE GLOW PLUG CONTROLLER
a.

Replace the glow plug controller (See page Engine / Hybrid System>1GD-FTV (STARTING)>GLOW PLUG CONTROLLER>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>CHECK MODE PROCEDURE).


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.

OK:

No DTC is output.


HINT:

Check for DTCs in check mode.




OK

END

NG

12.REPLACE GLOW PLUG ASSEMBLY
12.REPLACE GLOW PLUG ASSEMBLY
a.

Replace the glow plug assembly (See page Engine / Hybrid System>1GD-FTV (STARTING)>GLOW PLUG>REMOVAL).



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CHECK HARNESS AND CONNECTOR
a.

Disconnect connectors of the glow plug controller.

U169489E01
1.146,2.552 1.5,2.198 false 1.5,2.198 1.615,2.198 false 1.729,1.24 2.083,0.896 false 2.083,0.896 2.198,0.896 false 1.448,1.906 1.802,1.563 false 1.802,1.563 1.917,1.563 false 2.01,0.573 2.365,0.229 false 2.365,0.229 2.479,0.229 false 3.458,1.5 3.156,2.083 false 3.771,1.49 3.99,2.073 false 5.698,1.5 5.396,2.083 false 6.01,1.49 6.229,2.083 false 0.792,0.292 0.99,0.458 0.198,0.167 10 false *1 1.656,2.146 1.865,2.313 0.208,0.167 10 false 1 1.969,1.49 2.177,1.656 0.208,0.167 10 false 2 2.51,0.156 2.719,0.323 0.208,0.167 10 false 4 2.229,0.833 2.438,1 0.208,0.167 10 false 3 5.365,0.563 5.563,0.729 0.198,0.167 10 false *b 3.094,0.563 3.292,0.729 0.198,0.167 10 false *a 3.01,2.125 3.396,2.292 0.385,0.167 10 false GL1 3.906,2.125 4.292,2.292 0.385,0.167 10 false GL2 6.135,2.125 6.521,2.292 0.385,0.167 10 false GL4 5.229,2.125 5.615,2.292 0.385,0.167 10 false GL3 2.677,1.271 2.979,1.427 0.302,0.156 10 false A82 4.969,1.323 5.271,1.479 0.302,0.156 10 false A92


b.

Remove the No. 1 glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A82-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground Always Below 1 Ω
A82-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground Always Below 1 Ω
A92-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground Always Below 1 Ω
A92-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground Always Below 1 Ω


Text in Illustration
*1 No. 1 Glow Plug Connector - -
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)

HINT:

Make sure that there are no short circuits to the battery.



d.

Reconnect the glow plug controller connector.


e.

Reinstall the No. 1 glow plug connector.



OK

14.REPLACE GLOW PLUG CONTROLLER

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.REPLACE GLOW PLUG CONTROLLER
a.

Replace the glow plug controller (See page Engine / Hybrid System>1GD-FTV (STARTING)>GLOW PLUG CONTROLLER>REMOVAL).



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>CHECK MODE PROCEDURE).


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.

HINT:

Check for DTCs in check mode.




NEXT

END

17.INSPECT GLOW RELAY

OK

18.CHECK HARNESS AND CONNECTOR

NG

REPLACE GLOW RELAY

18.CHECK HARNESS AND CONNECTOR
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Remove the GLOW relay assembly.


d.

Remove the No. 1 glow plug connector from the glow plug.


e.

Disconnect connectors of the glow plug controller.


f.

Disconnect the ECM connectors.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GLOW relay terminal 5 - Battery positive terminal Always Below 1 Ω
GLOW relay terminal 1 - Body ground Always Below 1 Ω
GLOW relay terminal 3 - A80-1 (BATT) Always Below 1 Ω
GLOW relay terminal 2 - G184-15 (GREL) Always Below 1 Ω
GLOW relay terminal 5 or Battery positive terminal - Body ground and other terminals Always 10 kΩ or higher
GLOW relay terminal 3 or A80-1 (BATT) - Body ground and other terminals Always 10 kΩ or higher
GLOW relay terminal 2 or G184-15 (GREL) - Body ground and other terminals Always 10 kΩ or higher




OK

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR