Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P2009  Intake Manifold Runner Control Circuit Low (Bank 1)  P2010  Intake Manifold Runner Control Circuit High (Bank 1)  


DESCRIPTION

Refer to DTC P2006 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P2006).

P2009
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second Open in vacuum switching valve (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic).
·

Vacuum switching valve (for swirl control valve)

·

Open in vacuum switching valve (for swirl control valve) circuit

·

ECM



P2010
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second Short in vacuum switching valve (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic).
·

Vacuum switching valve (for swirl control valve)

·

Short in vacuum switching valve (for swirl control valve) circuit

·

ECM



WIRING DIAGRAM

A413241E01
2.385,1.615 5.448,2.083 3.063,0.469 10 false Vacuum Switching Valve (for Swirl Control Valve) 2.375,1.438 2.833,1.635 0.458,0.198 10 false C79 5.896,0.896 6.208,1.094 0.313,0.198 10 false 10 4.427,1 4.74,1.198 0.313,0.198 10 false 1 3.083,1 3.396,1.198 0.313,0.198 10 false 2 3.115,2.604 3.865,2.823 0.75,0.219 10 false EFI NO. 2 3.552,2.313 3.865,2.51 0.313,0.198 10 false 1 3.115,2.313 3.427,2.51 0.313,0.198 10 false 2 5.281,3.688 5.594,3.885 0.313,0.198 10 false 3 5.219,3.875 5.531,4.073 0.313,0.198 10 false 1W 5.823,1.104 6.229,1.313 0.406,0.208 10 false C149 6.396,6.063 6.781,6.271 0.385,0.208 10 false ECM 5.219,5.365 5.531,5.563 0.313,0.198 10 false 1W 5.292,5.177 5.604,5.375 0.313,0.198 10 false 8 3.292,4.542 4.365,4.76 1.073,0.219 10 false EFI-MAIN NO. 2 3.323,5.667 4.396,5.885 1.073,0.219 10 false EFI-MAIN NO. 1 2.448,5.135 3.521,5.354 1.073,0.219 10 false EFI-MAIN NO. 1 2.448,4 3.521,4.219 1.073,0.219 10 false EFI-MAIN NO. 2 4.469,4.573 5.115,4.969 0.646,0.396 10 false EFI-MAIN NO. 3 1.698,3.875 2.01,4.073 0.313,0.198 10 false 1S 1.76,5.167 2.073,5.365 0.313,0.198 10 false 4 0.573,6.01 1.646,6.229 1.073,0.219 10 false Battery 0.417,4.729 1.49,4.948 1.073,0.219 10 false 70A FL 1.76,3.698 2.073,3.896 0.313,0.198 10 false 1 1.729,5.354 2.042,5.552 0.313,0.198 10 false 1W 2.896,6.094 4.667,6.313 1.771,0.219 10 false No. 1 Integration Relay 5.813,5.365 6.198,5.573 0.385,0.208 10 false G184 5.906,5.156 6.219,5.354 0.313,0.198 10 false 14 6.24,5.167 6.688,5.385 0.448,0.219 10 false MREL 6.25,1.094 6.698,1.313 0.448,0.219 10 false SCV

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
A067588E16
0.819,0.027 1.530,0.235 0.711,0.208 10 VSV is ON 2.458,0.027 3.238,0.235 0.780,0.208 10 VSV is OFF 0.55,0.315 0.771,0.516 0.221,0.201 10 Air 2.332,1.753 2.812,1.954 0.480,0.201 10 Port E 0.699,1.782 1.179,1.983 0.480,0.201 10 Port E 1.621,1.627 2.092,1.828 0.471,0.201 10 Port F 0.103,1.639 0.574,1.840 0.471,0.201 10 Port F 2.005,0.384 2.226,0.585 0.221,0.201 10 Air 0.468,1.427 0.318,1.663 false 0.67,1.315 0.92,1.805 false 1.998,1.418 1.839,1.65 false 2.174,1.293 2.505,1.757 false 3.025,2.036 3.414,2.137 0.389,0.102 2.757,0.554 3.328,0.755 0.570,0.201 10 Air Filter

a.

Connect the GTS to the DLC3.


b.

Disconnect the vacuum hoses from the vacuum switching valve (for swirl control valve).


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.


e.

Check the vacuum switching valve (for swirl control valve) operation when it is operated using the GTS.

OK:
GTS Operation Specified Condition
VSV ON Air from port E flows out through port F
VSV OFF Air from port E flows out through air filter



f.

Reconnect the vacuum hoses.



OK

NG

2.INSPECT VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) (RESISTANCE)
2.INSPECT VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) (RESISTANCE)
a.

Inspect the vacuum switching valve (for swirl control valve) (See page Engine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>INSPECTION).



OK

3.INSPECT VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) (POWER SOURCE VOLTAGE)

NG

9.REPLACE VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE)
3.INSPECT VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) (POWER SOURCE VOLTAGE)
a.
U169379E02
0.177,0.063 0.344,0.229 0.167,0.167 10 false *a 0.479,1.073 0.781,1.229 0.302,0.156 10 false C79

Disconnect the vacuum switching valve (for swirl control valve) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C79-2 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Vacuum Switching Valve (for Swirl Control Valve))


c.

Reconnect the vacuum switching valve (for swirl control valve) connector.



OK

4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - NO. 1 INTEGRATION RELAY)
4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - ECM)
a.

Disconnect the vacuum switching valve (for swirl control valve) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance of the wire harness side connectors.

Standard Resistance:
Tester Connection Condition Specified Condition
C79-1 - C149-10 (SCV) Always Below 1 Ω
C79-1 or C149-10 (SCV) - Body ground and other terminal Always 10 kΩ or higher



d.

Reconnect the vacuum switching valve (for swirl control valve) connector.


e.

Reconnect the ECM connector.



OK

5.REPLACE ECM

NG

10.REPLACE NO. 1 INTEGRATION RELAY
5.REPLACE ECM

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the vacuum switching valve (for swirl control valve) connector.


c.

Measure the resistance of the wire harness side connectors.

Standard Resistance:
Tester Connection Condition Specified Condition
1W-3 - C79-2 Always Below 1 Ω
1W-3 or C79-2 - Body ground and other terminals Always 10 kΩ or higher



d.

Reinstall the No. 1 integration relay.


e.

Reconnect the vacuum switching valve (for swirl control valve) connector.



OK

7.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN 2)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN 2)
a.


OK

8.INSPECT ECM POWER SOURCE CIRCUIT

NG

10.REPLACE NO. 1 INTEGRATION RELAY
8.INSPECT ECM POWER SOURCE CIRCUIT

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE)
a.

Replace the vacuum switching valve (for swirl control valve) (See page Engine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>REMOVAL).



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE NO. 1 INTEGRATION RELAY

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace harness or connector.



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Start the engine and wait for 2 seconds or more.


d.

Race the engine for 1 second.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END