Refer to DTC P2006 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P2006).
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| 2 seconds after engine is started, race engine for 1 second | Open in vacuum switching valve assembly (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic). | ·
Vacuum switching valve assembly (for swirl control valve) ·
Open in vacuum switching valve assembly (for swirl control valve) circuit ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| 2 seconds after engine is started, race engine for 1 second | Short in vacuum switching valve assembly (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic). | ·
Vacuum switching valve assembly (for swirl control valve) ·
Short in vacuum switching valve assembly (for swirl control valve) circuit ·
ECM |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Disconnect the vacuum hoses from the vacuum switching valve assembly (for swirl control valve).
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.
Check the vacuum switching valve (for swirl control valve) operation when it is operated using the GTS.
| GTS Operation | Specified Condition |
|---|---|
| VSV ON | Air from port E flows out through port F |
| VSV OFF | Air from port E flows out through air filter |
Reconnect the vacuum hoses.
OK
NG
Inspect the vacuum switching valve assembly (for swirl control valve) (See page Engine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>INSPECTION).
OK
NG
Disconnect the vacuum switching valve assembly (for swirl control valve) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C79-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Vacuum Switching Valve Assembly (for Swirl Control Valve)) |
Reconnect the vacuum switching valve assembly (for swirl control valve) connector.
OK
NG
Disconnect the vacuum switching valve assembly (for swirl control valve) connector.
Disconnect the ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C79-1 - C149-10 (SCV) | Always | Below 1 Ω |
| C79-1 or C149-10 (SCV) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the vacuum switching valve assembly (for swirl control valve) connector.
Reconnect the ECM connector.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Remove the No. 1 integration relay from the engine room relay block.
Disconnect the vacuum switching valve assembly (for swirl control valve) connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1W-3 - C79-2 | Always | Below 1 Ω |
| 1W-3 or C79-2 - Body ground and other terminals | Always | 10 kΩ or higher |
Reinstall the No. 1 integration relay.
Reconnect the vacuum switching valve assembly (for swirl control valve) connector.
OK
NG
Inspect the No. 1 Integration relay (EFI MAIN2) (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY (w/ Urea SCR System)>ON-VEHICLE INSPECTION).
OK
NG
Check the ECM power source circuit (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>ECM Power Source Circuit).
NEXT
Replace the vacuum control valve set (See page Engine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>REMOVAL).
NEXT
NEXT
Repair or replace harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Start the engine and wait for 2 seconds or more.
Race the engine for 1 second.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT