Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › from 2017.08
RM27T0E _58 Vehicle Interior _053737 SEAT _0261110 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Wireless Transmitter Memory Function does not Operate  


DESCRIPTION

With the ignition switch ON, press the manual door control switch LOCK or UNLOCK while holding a seat memory switch (M1 switch or M2 switch). Doing so registers the transmitter recognition code into the seat memory switch that was pressed. After registration is completed, the answer-back buzzer sounds.

CAUTION / NOTICE / HINT

NOTICE:

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom.


PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL FUNCTION
a.

Using the standard operation procedure, check that the power door lock/unlock function operates normally (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Power door lock/unlock function operates normally.




OK

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

NG

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
a.

Using the standard operation procedure, check that the wireless door lock/unlock function operates normally (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)>OPERATION CHECK).

OK:

Wireless door lock/unlock function operates normally.




OK

3.CHECK VEHICLE TYPE

NG

3.CHECK VEHICLE TYPE
a.

Check vehicle type.

Result
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B



A

4.CHECK ENTRY AND START SYSTEM (ENTRY UNLOCK FUNCTION)

B

5.CHECK SEAT MEMORY FUNCTION
4.CHECK ENTRY AND START SYSTEM (ENTRY UNLOCK FUNCTION)
a.

Check the entry unlock function of the entry and start system (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

OK:

Entry unlock function operates normally.




OK

5.CHECK SEAT MEMORY FUNCTION

NG

5.CHECK SEAT MEMORY FUNCTION
a.

Perform a seat memory operation properly (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK).


b.

Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory operation.

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

·

If a memorizing operation fails, release all switches. The seat memory function does not operate unless the switches are released.



OK:

Seat position memory function operates normally.




OK

6.READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY)

NG

GO TO PROBLEM SYMPTOMS TABLE (Power Seat Position is not Memorized)

6.READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY)
a.

Using the intelligent tester, read the Data List (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D-Door Courtesy Front door courtesy light switch assembly signal / ON or OFF ON: Driver side door open
OFF: Driver side door closed
-

OK:

On intelligent tester screen, each item changes between ON and OFF according to above chart.




OK

7.CHECK MEMORY CALL FUNCTION (MEMORY ERASURE)

NG

7.CHECK MEMORY CALL FUNCTION (MEMORY ERASURE)
a.


NEXT

8.READ VALUE USING INTELLIGENT TESTER (MEMORY REGISTRATION)
8.READ VALUE USING INTELLIGENT TESTER (MEMORY REGISTRATION)
a.

Perform the memory registration operation while checking the tester screen (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Mem SW No. w/KeyID1 Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID1
MEM SW1: M1 switch linked with key ID1
MEM SW2: M2 switch linked with key ID1
MEM SW3: Related switch does not exist
-
Mem SW No. w/KeyID2 Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID2
MEM SW1: M1 switch linked with key ID2
MEM SW2: M2 switch linked with key ID2
MEM SW3: Related switch does not exist
-
Mem SW No. w/KeyID3 Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID3
MEM SW1: M1 switch linked with key ID3
MEM SW2: M2 switch linked with key ID3
MEM SW3: Related switch does not exist
-
Mem SW No. w/KeyID4 Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID4
MEM SW1: M1 switch linked with key ID4
MEM SW2: M2 switch linked with key ID4
MEM SW3: Related switch does not exist
-
Mem SW No. w/KeyID5 Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID5
MEM SW1: M1 switch linked with key ID5
MEM SW2: M2 switch linked with key ID5
MEM SW3: Related switch does not exist
-
Mem SW No. w/KeyID6 Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID6
MEM SW1: M1 switch linked with key ID6
MEM SW2: M2 switch linked with key ID6
MEM SW3: Related switch does not exist
-
Mem SW No. w/KeyID7 Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID7
MEM SW1: M1 switch linked with key ID7
MEM SW2: M2 switch linked with key ID7
MEM SW3: Related switch does not exist
-

OK:

On the tester display, it is confirmed that the memory call is registered.




OK

9.CHECK MEMORY CALL FUNCTION (SEAT MEMORY CALL)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

9.CHECK MEMORY CALL FUNCTION (SEAT MEMORY CALL)
a.

With a recognition code stored in memory, open the driver door after performing an entry unlock operation or pressing the transmitter unlock switch. Check that the driver side power seat moves to the memorized position (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK).

OK:

Driver side power seat moves to the memorized position.




OK

NG

GO TO PROBLEM SYMPTOMS TABLE (Wireless-linked Return Function does not Operate)