Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0260748 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Distance Control Switch Circuit  


DESCRIPTION

The vehicle-to-vehicle distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The vehicle-to-vehicle distance control switch is installed in the steering pad switch assembly. The vehicle-to-vehicle distance set value can be changed by operating the vehicle-to-vehicle distance control switch (steering pad switch assembly) while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.

WIRING DIAGRAM

C384959E02
1.208,0.708 2.844,1.229 1.635,0.521 10 false Vehicle-to-vehicle distance control switch 0.885,2.635 3.073,2.885 2.188,0.25 10 false Steering Pad Switch Assembly 3.177,2.573 5.052,2.813 1.875,0.24 10 false Spiral Cable Subassembly 6.208,2.646 6.74,2.865 0.531,0.219 10 false ECM 5.844,1.156 6.844,1.521 1,0.365 10 false Driving Support ECU Assembly 6.063,0.552 6.677,0.75 0.615,0.198 10 false SPSW 6.073,2.01 6.688,2.208 0.615,0.198 10 false ECCS 5.833,1 6.448,1.198 0.615,0.198 10 false G224 6.198,2.469 6.813,2.667 0.615,0.198 10 false G181 4.188,0.552 4.802,0.75 0.615,0.198 10 false G208 4.177,2.01 4.792,2.208 0.615,0.198 10 false G208 3.042,0.552 3.323,0.76 0.281,0.208 10 false z7 3.792,0.448 4.406,0.646 0.615,0.198 10 false DIST 3.802,1.906 4.417,2.104 0.615,0.198 10 false ECC 4.302,1.802 4.615,2 0.313,0.198 10 false 2 4.271,0.344 4.583,0.542 0.313,0.198 10 false 12 3.063,0.344 3.375,0.542 0.313,0.198 10 false 4 3.042,2.01 3.396,2.229 0.354,0.219 10 false z7 3.063,1.792 3.375,1.99 0.313,0.198 10 false 7 0.333,3.042 2.323,3.24 1.99,0.198 10 false *1: for 2TR-FE 0.333,3.365 3.052,3.635 2.719,0.271 10 false *2: for 1GR-FE, 1GD-FTV, 1KD-FTV 5.073,2.25 5.396,2.49 0.323,0.24 10 false *2 5.823,0.448 6.135,0.646 0.313,0.198 10 false 23 5.813,1.906 6.125,2.104 0.313,0.198 10 false 21 5.552,2.115 5.875,2.354 0.323,0.24 10 false *1

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.READ VALUE USING GTS (DISTANCE CONTROL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Check the Data List to confirm function of the distance control switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Powertrain > Radar Cruise2 > Data List

Tester Display Measurement Item Range Normal Condition Diagnostic Note
Distance Control Switch Distance control switch signal ON or OFF ON: Vehicle-to-vehicle distance control switch on
OFF: Vehicle-to-vehicle distance control switch off
-

OK:

The display changes in accordance with switch operation.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING WHEEL>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING WHEEL>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY AND ECM)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY AND ECM)
a.

Disconnect the G208 spiral cable sub-assembly connector.


b.

Disconnect the G224 driving support ECU assembly connector.


c.

Disconnect the G181*1 ECM connector.

·

for 2TR-FE



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 2TR-FE):
Tester Connection Condition Specified Condition
G208-12 (DIST) - G224-23 (SPSW) Always Below 1 Ω
G208-2 (ECC) - G181-21 (ECCS) Always Below 1 Ω
G208-12 (DIST) or G224-23 (SPSW) - Body ground Always 10 kΩ or higher


Standard Resistance (for 1GR-FE, 1KD-FTV and 1GD-FTV):
Tester Connection Condition Specified Condition
G208-12 (DIST) - G224-23 (SPSW) Always Below 1 Ω
G208-2 (ECC) - Body ground Always Below 1 Ω
G208-12 (DIST) or G224-23 (SPSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR