Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM › from 2017.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260870 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1715  Front Acceleration Sensor RH Malfunction  C1716  Front Acceleration Sensor LH Malfunction  C1717  Rear Acceleration Sensor Malfunction  C1796  (Up&Down)G Sensor FR  C1797  (Up&Down)G Sensor FL  C1798  (Up&Down)G Sensor Rear  


DESCRIPTION

The acceleration sensor (up and down G sensor) detects the upward and downward acceleration of the vehicle, and outputs it as a voltage to the suspension control ECU. Up and down G sensors are installed in 3 locations: 1) the suspension control ECU, 2) the RH side instrument panel, and 3) behind the deck trim side panel assembly LH. Each up and down G sensor independently detects the upward and downward acceleration. During a test mode inspection, the suspension control ECU reads the fluctuations in each sensor signal. If a sensor signal does not fluctuate, test mode DTCs C1796, C1797 and C1798 are stored.

DTC Code DTC Detection Condition Trouble Area
C1715 Either condition is met:
·

With the ignition switch ON, a voltage of 5.5 V or higher or 4.3 V or less at the power source of the front acceleration sensor RH is detected for 0.5 seconds.

·

With the ignition switch ON, a voltage of 4.7 V or higher or 0.3 V or less at the front acceleration sensor RH is detected for 1 second.


·

Harness or connector

·

Front acceleration sensor RH

·

Suspension control ECU


C1716 Either condition is met:
·

With the ignition switch ON, a voltage of 5.5 V or higher or 4.3 V or less at the power source of the front acceleration sensor LH is detected for 0.5 seconds.

·

With the ignition switch ON, a voltage of 4.7 V or higher or 0.3 V or less at the front acceleration sensor LH is detected for 1 second.


Suspension control ECU (Front acceleration sensor LH)
C1717 Either condition is met:
·

With the ignition switch ON, a voltage of 5.5 V or higher or 4.3 V or less at the power source of the rear acceleration sensor is detected for 0.5 seconds.

·

With the ignition switch ON, a voltage of 4.7 V or higher or 0.3 V or less at the rear acceleration sensor is detected for 1 second.


·

Harness or connector

·

Rear acceleration sensor

·

Suspension control ECU


C1796 On a level surface, the G sensor input is +/- 1.96 m/s2 or more for 1 second or more.
·

Harness or connector

·

Front acceleration sensor RH

·

Suspension control ECU


C1797 On a level surface, the G sensor input is +/- 1.96 m/s2 or more for 1 second or more. Suspension control ECU (Front acceleration sensor LH)
C1798 On a level surface, the G sensor input is +/- 1.96 m/s2 or more for 1 second or more.
·

Harness or connector

·

Rear acceleration sensor

·

Suspension control ECU



HINT:

If DTCs C1716 and C1797 are output, replace the suspension control ECU (houses the front acceleration sensor LH).


WIRING DIAGRAM

C179515E16
0.24,2.292 0.563,2.479 0.323,0.188 10 false A13 0.25,2.448 2.115,2.667 1.865,0.219 10 false Front Acceleration Sensor RH 1.542,1.688 1.698,1.896 0.156,0.208 10 false 2 0.281,5.01 0.583,5.198 0.302,0.188 10 false R18 0.281,5.167 2.302,5.542 2.021,0.375 10 false Rear Acceleration Sensor 5.417,5.063 6.99,5.344 1.573,0.281 10 false Suspension Control ECU 1.531,1.083 1.688,1.292 0.156,0.208 10 false 1 1.531,0.5 1.688,0.708 0.156,0.208 10 false 3 5.646,0.438 5.792,0.604 0.146,0.167 10 false 9 5.583,1.01 5.802,1.219 0.219,0.208 10 false 18 5.896,0.625 6.323,0.833 0.427,0.208 10 false SBR 5.896,1.219 6.323,1.427 0.427,0.208 10 false SGFR 5.896,1.813 6.323,2.021 0.427,0.208 10 false SGR 1.125,0.625 1.479,0.833 0.354,0.208 10 false SHB 1.042,1.24 1.469,1.448 0.427,0.208 10 false SGFL 1.104,1.813 1.458,2.021 0.354,0.208 10 false SHG 5.896,3.365 6.323,3.573 0.427,0.208 10 false SBR3 5.896,3.969 6.323,4.177 0.427,0.208 10 false SGRR 5.896,4.552 6.323,4.76 0.427,0.208 10 false SGR3 5.583,1.583 5.802,1.792 0.219,0.208 10 false 10 5.583,3.135 5.802,3.344 0.219,0.208 10 false 17 5.583,3.719 5.802,3.927 0.219,0.208 10 false 26 5.583,4.344 5.802,4.552 0.219,0.208 10 false 16 5.552,0.635 5.844,0.823 0.292,0.188 10 false A14 1.552,4.417 1.708,4.625 0.156,0.208 10 false 2 1.552,3.823 1.708,4.031 0.156,0.208 10 false 1 1.552,3.229 1.708,3.438 0.156,0.208 10 false 3 1.115,3.365 1.469,3.573 0.354,0.208 10 false SGV 1.021,3.958 1.458,4.167 0.438,0.208 10 false SGRR 1.021,4.552 1.479,4.76 0.458,0.208 10 false SGND 5.542,3.354 5.813,3.542 0.271,0.188 10 false A49 5.542,1.219 5.833,1.406 0.292,0.188 10 false A14 5.552,1.823 5.844,2.01 0.292,0.188 10 false A14 5.552,3.948 5.823,4.135 0.271,0.188 10 false A49 5.542,4.552 5.813,4.74 0.271,0.188 10 false A49

CAUTION / NOTICE / HINT

NOTICE:

When replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


PROCEDURE

1.READ VALUE USING GTS (G SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Air suspension / Data List.

Air Suspension
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
(Up & Down) G Sensor FR (Up & Down) G sensor (Front RH)/
Min.: -1045.29 m/s2
Max.: 1045.26 m/s2
0 +/- 0.98 m/s2 when stationary The value changes when the vehicle (Front RH) is bounced.
(Up & Down) G Sensor FL (Up & Down) G sensor (Front LH)/
Min.: -1045.29 m/s2
Max.: 1045.26 m/s2
0 +/- 0.98 m/s2 when stationary The value changes when the vehicle (Front LH) is bounced.
(Up & Down) G Sensor Rear (Up & Down) G sensor (Rear)/
Min.: -1045.29 m/s2
Max.: 1045.26 m/s2
0 +/- 0.98 m/s2 when stationary The value changes when the vehicle (rear) is bounced.

OK:

Acceleration value changes.




OK

NG

2.INSPECT ACCELERATION SENSOR (FRONT RH OR REAR)
2.INSPECT ACCELERATION SENSOR (FRONT RH OR REAR)
U148403E02
2.427,1.583 2.458,2.125 2.458,2.125 2.583,2.125 false 1.948,1.583 1.521,1.833 1.521,1.833 1.406,1.833 false 0.073,0 0.323,0.188 0.25,0.188 10 false *a 2.656,2.042 3.25,2.396 0.594,0.354 10 false SGFL*A, SGRR*B 0.854,1.719 1.375,2.031 0.521,0.313 10 false SHB*A, SGV*B 2.656,0.146 3.229,0.49 0.573,0.344 10 false SHG*A, SGND*B

Text in Illustration
*A for Front RH
*B for Rear
*a Component without harness connected
(Acceleration Sensor)
V100135

Upside
V100136

Downside

a.

Check the front acceleration sensor RH (when DTC C1715 or C1796 is output).

i.

Remove the front acceleration sensor RH (See page Suspension>SUSPENSION CONTROL>FRONT ACCELERATION SENSOR>REMOVAL).


ii.

Connect 3 dry cell batteries of 1.5 V in series.


iii.

Connect the positive (+) end of the batteries to terminal 3 (SHB) of the acceleration sensor and the negative (-) end of the batteries to terminal 2 (SHG). Then measure the voltage between terminal 1 (SGFL) and terminal 2 (SHG).


iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (SGFL) - 2 (SHG) Sensor in vertical position Approx. 2.0 to 2.5 V
Sensor tilted left or right from vertical position Changes between approx. 0.9 and 2.3 V




b.

Check the rear acceleration sensor: (when DTC C1717 or C1798 is output).

i.

Remove the rear acceleration sensor (See page Suspension>SUSPENSION CONTROL>REAR ACCELERATION SENSOR>REMOVAL).


ii.

Connect 3 dry cell batteries of 1.5 V in series.


iii.

Connect the positive (+) end of the batteries to terminal 3 (SGV) of the acceleration sensor and the negative (-) end of the batteries to terminal 2 (SGND). Then measure the voltage between terminal 1 (SGRR) and terminal 2 (SGND).


iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (SGRR) - 2 (SGND) Sensor in vertical position Approx. 2.0 to 2.5 V
Sensor tilted left or right from vertical position Changes between approx. 0.9 and 2.3 V


NOTICE:

Do not apply a voltage of higher than 6 V.


HINT:

When the acceleration sensor is tilted, it may output a different value.


Result
Result Proceed to
OK A
NG (Front acceleration sensor RH) B
NG (Rear acceleration sensor) C




A

3.CHECK HARNESS AND CONNECTOR (ACCELERATION SENSOR - SUSPENSION CONTROL ECU)

B

REPLACE FRONT ACCELERATION SENSOR RH

C

REPLACE REAR ACCELERATION SENSOR

3.CHECK HARNESS AND CONNECTOR (ACCELERATION SENSOR - SUSPENSION CONTROL ECU)
a.

Check the front acceleration sensor RH (when DTC C1715 or C1796 is output).

i.

Disconnect the A13 front acceleration sensor RH connector.


ii.

Disconnect the A14 suspension control ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-1 (SGFL) - A14-18 (SGFR) Always Below 1 Ω
A13-2 (SHG) - A14-10 (SGR) Always Below 1 Ω
A13-3 (SHB) - A14-9 (SBR) Always Below 1 Ω
A13-1 (SGFL) - Body ground Always 10 kΩ or higher
A13-2 (SHG) - Body ground Always 10 kΩ or higher
A13-3 (SHB) - Body ground Always 10 kΩ or higher




b.

Check the rear acceleration sensor: (when DTC C1717 or C1798 is output).

i.

Disconnect the R18 rear acceleration sensor connector.


ii.

Disconnect the A49 suspension control ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R18-1 (SGRR) - A49-26 (SGRR) Always Below 1 Ω
R18-2 (SGND) - A49-16 (SGR3) Always Below 1 Ω
R18-3 (SGV) - A49-17 (SBR3) Always Below 1 Ω
R18-1 (SGRR) - Body ground Always 10 kΩ or higher
R18-2 (SGND) - Body ground Always 10 kΩ or higher
R18-3 (SGV) - Body ground Always 10 kΩ or higher





OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR