The suspension control ECU operates the exhaust solenoid valve (height control compressor), releases the air from the height control cylinder assembly (pneumatic cylinder) and lowers the vehicle height.
When the vehicle height is lowered, the suspension control ECU opens the height control valve and then operates the exhaust solenoid valve to release compressed air to the outside.
The exhaust solenoid valve is on the compressor unit and has only one valve.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1745 | Either condition is met:
·
With the exhaust solenoid valve not activated, an open signal of the exhaust solenoid valve is detected for 1 second or more. ·
With the exhaust solenoid valve activated, a short signal of the exhaust solenoid valve is detected 8 times successively. |
·
Harness or connector ·
Exhaust solenoid valve (Height control compressor) ·
Suspension control ECU |
Once the suspension control ECU stores DTC C1745 in memory, vehicle height control is suspended until a normal signal is input to the suspension control ECU from the exhaust solenoid valve. However, control is resumed if the ignition switch is turned off and then to ON again.
Malfunction in the exhaust solenoid valve:
Height control indicator N comes on or blinks and HI and LO do not come on by operating the height control switch "up" or "down".
When replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).
If DTC C1782 is output at the same time as C1745, perform the inspection necessary for DTC C1782 first (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>C1782).
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Air suspension / Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Exhaust Solenoid | Exhaust solenoid valve | ON or OFF | ·
The operating sound of the solenoid (clicking sound) can be heard. ·
When the Active Test is performed, Exhaust Solenoid in the Data List changes between ON and OFF accordingly. |
Operation of solenoid (clicking sound) can be heard.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (When troubleshooting according to problem symptoms table) | B |
| OK (When troubleshooting according to DTC chart) | C |
A
B
C
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Disconnect the S10 exhaust solenoid valve connector.
Disconnect the R19 suspension control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S10-2 (L) - R19-9 (SLEX) | Always | Below 1 Ω |
| S10-2 (L) - Body ground | Always | 10 kΩ or higher |
| S10-1 (B) - Body ground | Always | Below 1 Ω |
OK
NG
Turn the ignition switch off.
Remove the height control compressor (See page Suspension>SUSPENSION CONTROL>HEIGHT CONTROL COMPRESSOR>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (L) - 1 (B) | 20°C (68°F) | 10 to 14 Ω |
| *a | Component without harness connected
(Exhaust Valve) |
Connect the positive (+) lead of the battery to terminal 2 (L) and the negative (-) lead to terminal 1 (B) of the solenoid valve connector. Then check that the valve makes an operating sound.
Operation of solenoid (clicking sound) can be heard.
OK
NG