The video signal from the each television camera is transmitted to the navigation receiver assembly*1 or radio and display receiver assembly*2.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
When "!" mark is displayed on the navigation receiver assembly*1 or radio and display receiver assembly*2 after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION
*1: for Navigation Receiver Type
*2: for Radio and Display Type
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Electrical devices are used in the cabin (noise may occur in the image).
The camera lens is frosted over (the image immediately after turning the power switch on (IG) may be blurred or darker than normal).
The camera lens is dirty with snow, mud, etc.
A strong beam of light, such as a sunbeam or headlight, hits the camera.
It is too dark around the camera (at night, etc.).
The ambient temperature around the camera is either too high or too low.
The vehicle is tilted at a steep angle.
The television camera assembly lens is scratched.
The television camera assembly lens has drops of water on it or the humidity is high.
When the camera is used under fluorescent lights, sodium lights, or mercury lights, etc., the lights and the illuminated area may appear to flicker.
Check if the same malfunction occurs when the panoramic view monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Rear view screen is not displayed. | A |
| Front view screen is not displayed. | B |
| Left side monitor screen is not displayed (for LHD). | C |
| Left side monitor screen is not displayed (for RHD). | D |
| Right side monitor screen is not displayed (for LHD). | E |
| Right side monitor screen is not displayed (for RHD). | F |
| Panoramic view monitor screen is not displayed (for Navigation Receiver Type). | G |
| Panoramic view monitor screen is not displayed (for Radio and Display Type). | H |
A
B
C
D
E
F
G
H
*1: w/o Tire Carrier
*2: w/ Tire Carrier
Disconnect the I7 parking assist ECU connector.
Disconnect the X10*1 or v3*2 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-38 (CV-) - X10-2 (CV-) | Always | Below 1 Ω |
| I7-15 (CV+) - X10-3 (CV+) | Always | Below 1 Ω |
| I7-14 (CB+) - X10-6 (CB+) | Always | Below 1 Ω |
| I7-37 (CGND) - X10-5 (CGND) | Always | Below 1 Ω |
| I7-38 (CV-) or X10-2 (CV-) - Body ground | Always | 10 kΩ or higher |
| I7-15 (CV+) or X10-3 (CV+) - Body ground | Always | 10 kΩ or higher |
| I7-14 (CB+) or X10-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| I7-37 (CGND) or X10-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-38 (CV-) - v3-2 (CV-) | Always | Below 1 Ω |
| I7-15 (CV+) - v3-3 (CV+) | Always | Below 1 Ω |
| I7-14 (CB+) - v3-6 (CB+) | Always | Below 1 Ω |
| I7-37 (CGND) - v3-5 (CGND) | Always | Below 1 Ω |
| I7-38 (CV-) or v3-2 (CV-) - Body ground | Always | 10 kΩ or higher |
| I7-15 (CV+) or v3-3 (CV+) - Body ground | Always | 10 kΩ or higher |
| I7-14 (CB+) or v3-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| I7-37 (CGND) or v3-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Parking Assist ECU) |
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 38 (CV-) - Body ground | Always | Below 1 Ω |
| 37 (CGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL
for RHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL
| *a | Component with harness connected
(Parking Assist ECU) |
Disconnect the rear television camera assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I7-14 (CB+) - I7-37 (CGND) | Engine switch on (IG) | 5.5 to 7.05 V |
| I7-14 (CB+) - I7-37 (CGND) | Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL
for RHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL
Check the waveform of the rear television camera assembly using an oscilloscope.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform A |
| *c | Waveform B | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the rear television camera assembly.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | I7-15 (CV+) - I7-37 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | ·
Waveform A: Engine switch on (IG), shift lever in R and camera lens is not covered, displaying an image ·
Waveform B: Engine switch on (IG), shift lever in R and camera lens is covered, blacking out the screen |
Waveform is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL
for RHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL
NG
w/o Tire Carrier:
w/ Tire Carrier:
Disconnect the I7 parking assist ECU connector.
Disconnect the g1 front television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-36 (BCV-) - g1-2 (BCV-) | Always | Below 1 Ω |
| I7-12 (BCV+) - g1-3 (BCV+) | Always | Below 1 Ω |
| I7-35 (BGND) - g1-5 (BGND) | Always | Below 1 Ω |
| I7-11 (BCB+) - g1-6 (BCB+) | Always | Below 1 Ω |
| I7-36 (BCV-) - Body ground | Always | 10 kΩ or higher |
| I7-12 (BCV+) - Body ground | Always | 10 kΩ or higher |
| I7-35 (BGND) - Body ground | Always | 10 kΩ or higher |
| I7-11 (BCB+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Parking Assist ECU) |
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 35 (BGND) - Body ground | Always | Below 1 Ω |
| 36 (BCV-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
NG
OK
for LHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL
for RHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL
| *a | Component with harness connected
(Parking Assist ECU) |
Disconnect the front television camera assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I7-11 (BCB+) - I7-35 (BGND) | Engine switch on (IG) | 5.5 to 7.05 V |
| I7-11 (BCB+) - I7-35 (BGND) | Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL
for RHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL
Check the ware form of the front television camera assembly using an oscilloscope.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform A |
| *c | Waveform B | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the front television camera assembly.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | I7-12 (BCV+) - I7-35 (BGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | ·
Waveform A: Engine switch on (IG), panoramic view monitor switch (multi-terrain monitor switch) on and camera lens is not covered, displaying an image ·
Waveform B: Engine switch on (IG), panoramic view monitor switch (multi-terrain monitor switch) on and camera lens is covered, blacking out the screen |
Waveform is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL
for RHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Front)>REMOVAL
Disconnect the I7 parking assist ECU connector.
Disconnect the K11 outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-2 (DCB+) - K11-6 (SCB+) | Always | Below 1 Ω |
| I7-5 (DCV+) - K11-2 (SCV+) | Always | Below 1 Ω |
| I7-4 (DCV-) - K11-3 (SCV-) | Always | Below 1 Ω |
| I7-3 (DGND) - K11-7 (SGND) | Always | Below 1 Ω |
| I7-2 (DCB+) or K11-6 (SCB+) - Body ground | Always | 10 kΩ or higher |
| I7-5 (DCV+) or K11-2 (SCV+) - Body ground | Always | 10 kΩ or higher |
| I7-4 (DCV-) or K11-3 (SCV-) - Body ground | Always | 10 kΩ or higher |
| I7-3 (DGND) or K11-7 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Parking Assist ECU) |
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (DGND) - Body ground | Always | Below 1 Ω |
| 4 (DCV-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Disconnect the outer rear view mirror assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I7-2 (DCB+) - I7-3 (DGND) | Engine switch on (ACC) | 5.5 to 7.05 V |
| I7-2 (DCB+) - I7-3 (DGND) | Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
Using an oscilloscope, check the waveform of the side television camera assembly LH.
A waterproof connector is used for the side television camera assembly LH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the side television camera assembly LH.
| Item | Content |
|---|---|
| Tester Connection | I7-5 (DCV+) - I7-3 (DGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Engine switch on (IG), panoramic view monitor switch (multi-terrain monitor switch) on |
Waveform is similar to that shown in illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to Side Television Camera Assembly LH) |
| *b | Component without harness connected
(to Outer Mirror Actuator Assembly LH) |
Disconnect the outer rear view mirror assembly LH connector.
Disconnect the side television camera assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 (SCB+) - K11-6 (SCB+) | Always | Below 1 Ω |
| B-3 (SCV+) - K11-2 (SCV+) | Always | Below 1 Ω |
| B-7 (SCV-) - K11-3 (SCV-) | Always | Below 1 Ω |
| B-5 (SGND) - K11-7 (SGND) | Always | Below 1 Ω |
| B-1 (SCB+) or K11-6 (SCB+) - Body ground | Always | 10 kΩ or higher |
| B-3 (SCV+) or K11-2 (SCV+) - Body ground | Always | 10 kΩ or higher |
| B-7 (SCV-) or K11-3 (SCV-) - Body ground | Always | 10 kΩ or higher |
| B-5 (SGND) or K11-7 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly LH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL
Check if the same malfunction reoccurs when the side monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Malfunction does not reoccur (returns to normal) | A |
| Malfunction reoccurs | B |
A
B
Disconnect the I7 parking assist ECU connector.
Disconnect the K11 outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-31 (SCB+) - K11-6 (SCB+) | Always | Below 1 Ω |
| I7-10 (SCV+) - K11-2 (SCV+) | Always | Below 1 Ω |
| I7-33 (SCV-) - K11-3 (SCV-) | Always | Below 1 Ω |
| I7-32 (SGND) - K11-7 (SGND) | Always | Below 1 Ω |
| I7-31 (SCB+) or K11-6 (SCB+) - Body ground | Always | 10 kΩ or higher |
| I7-10 (SCV+) or K11-2 (SCV+) - Body ground | Always | 10 kΩ or higher |
| I7-33 (SCV-) or K11-3 (SCV-) - Body ground | Always | 10 kΩ or higher |
| I7-32 (SGND) or K11-7 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Parking Assist ECU) |
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 32 (SGND) - Body ground | Always | Below 1 Ω |
| 33 (SCV-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Disconnect the outer rear view mirror assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I7-31 (SCB+) - I7-32 (SGND) | Engine switch on (ACC) | 5.5 to 7.05 V |
| I7-31 (SCB+) - I7-32 (SGND) | Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
Using an oscilloscope, check the waveform of the side television camera assembly LH.
A waterproof connector is used for the side television camera assembly LH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the side television camera assembly LH.
The video waveform is constantly output when the engine switch is on (ACC).
| Item | Content |
|---|---|
| Tester Connection | I7-10 (SCV+) - I7-32 (SGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Engine switch on (IG), panoramic view monitor switch (multi-terrain monitor switch) on |
Waveform is similar to that shown in illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to Side Television Camera Assembly LH) |
| *b | Component without harness connected
(to Outer Mirror Actuator Assembly LH) |
Disconnect the outer rear view mirror assembly LH connector.
Disconnect the side television camera assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 (SCB+) - K11-6 (SCB+) | Always | Below 1 Ω |
| B-3 (SCV+) - K11-2 (SCV+) | Always | Below 1 Ω |
| B-7 (SCV-) - K11-3 (SCV-) | Always | Below 1 Ω |
| B-5 (SGND) - K11-7 (SGND) | Always | Below 1 Ω |
| B-1 (SCB+) or K11-6 (SCB+) - Body ground | Always | 10 kΩ or higher |
| B-3 (SCV+) or K11-2 (SCV+) - Body ground | Always | 10 kΩ or higher |
| B-7 (SCV-) or K11-3 (SCV-) - Body ground | Always | 10 kΩ or higher |
| B-5 (SGND) or K11-7 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly LH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL
Check if the same malfunction reoccurs when the side monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Malfunction does not reoccur (returns to normal) | A |
| Malfunction reoccurs | B |
A
B
Disconnect the I7 parking assist ECU connector.
Disconnect the J11 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-31 (SCB+) - J11-6 (DCB+) | Always | Below 1 Ω |
| I7-10 (SCV+) - J11-2 (DCV+) | Always | Below 1 Ω |
| I7-33 (SCV-) - J11-3 (DCV-) | Always | Below 1 Ω |
| I7-32 (SGND) - J11-7 (DGND) | Always | Below 1 Ω |
| I7-31 (SCB+) or J11-6 (DCB+) - Body ground | Always | 10 kΩ or higher |
| I7-10 (SCV+) or J11-2 (DCV+) - Body ground | Always | 10 kΩ or higher |
| I7-33 (SCV-) or J11-3 (DCV-) - Body ground | Always | 10 kΩ or higher |
| I7-32 (SGND) or J11-7 (DGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Parking Assist ECU) |
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 32 (SGND) - Body ground | Always | Below 1 Ω |
| 33 (SCV-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Disconnect the outer rear view mirror assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I7-31 (SCB+) - I7-32 (SGND) | Engine switch on (ACC) | 5.5 to 7.05 V |
| I7-31 (SCB+) - I7-32 (SGND) | Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
Using an oscilloscope, check the waveform of the side television camera assembly RH.
A waterproof connector is used for the side television camera assembly RH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the side television camera assembly RH.
| Item | Content |
|---|---|
| Tester Connection | I7-10 (SCV+) - I7-32 (SGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Engine switch on (IG), panoramic view monitor switch (multi-terrain monitor switch) on |
Waveform is similar to that shown in illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to Side Television Camera Assembly RH) |
| *b | Component without harness connected
(to Outer Mirror Actuator Assembly RH) |
Disconnect the outer rear view mirror assembly RH connector.
Disconnect the side television camera assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (SCB+) - J11-6 (DCB+) | Always | Below 1 Ω |
| A-3 (SCV+) - J11-2 (DCV+) | Always | Below 1 Ω |
| A-7 (SCV-) - J11-3 (DCV-) | Always | Below 1 Ω |
| A-5 (SGND) - J11-7 (DGND) | Always | Below 1 Ω |
| A-1 (SCB+) or J11-6 (DCB+) - Body ground | Always | 10 kΩ or higher |
| A-3 (SCV+) or J11-2 (DCV+) - Body ground | Always | 10 kΩ or higher |
| A-7 (SCV-) or J11-3 (DCV-) - Body ground | Always | 10 kΩ or higher |
| A-5 (SGND) or J11-7 (DGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly RH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL
Check if the same malfunction reoccurs when the side monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Malfunction does not reoccur (returns to normal) | A |
| Malfunction reoccurs | B |
A
B
Disconnect the I7 parking assist ECU connector.
Disconnect the J11 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-2 (DCB+) - J11-6 (DCB+) | Always | Below 1 Ω |
| I7-5 (DCV+) - J11-2 (DCV+) | Always | Below 1 Ω |
| I7-4 (DCV-) - J11-3 (DCV-) | Always | Below 1 Ω |
| I7-3 (DGND) - J11-7 (DGND) | Always | Below 1 Ω |
| I7-2 (DCB+) or J11-6 (DCB+) - Body ground | Always | 10 kΩ or higher |
| I7-5 (DCV+) or J11-2 (DCV+) - Body ground | Always | 10 kΩ or higher |
| I7-4 (RCV-) or J11-3 (DCV-) - Body ground | Always | 10 kΩ or higher |
| I7-3 (DGND) or J11-7 (DGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Parking Assist ECU) |
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (DGND) - Body ground | Always | Below 1 Ω |
| 4 (DCV-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Disconnect the outer rear view mirror assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I7-2 (DCB+) - I7-3 (DGND) | Engine switch on (ACC) | 5.5 to 7.05 V |
| I7-2 (DCB+) - I7-3 (DGND) | Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
Using an oscilloscope, check the waveform of the side television camera assembly RH.
A waterproof connector is used for the side television camera assembly RH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the side television camera assembly LH.
| Item | Content |
|---|---|
| Tester Connection | I7-5 (DCV+) - I7-3 (DGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Engine switch on (IG), panoramic view monitor switch (multi-terrain monitor switch) on |
Waveform is similar to that shown in illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to Side Television Camera Assembly RH) |
| *b | Component without harness connected
(to Outer Mirror Actuator Assembly RH) |
Disconnect the outer rear view mirror assembly RH connector.
Disconnect the side television camera assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (SCB+) - J11-6 (DCB+) | Always | Below 1 Ω |
| A-3 (SCV+) - J11-2 (DCV+) | Always | Below 1 Ω |
| A-7 (SCV-) - J11-3 (DCV-) | Always | Below 1 Ω |
| A-5 (SGND) - J11-7 (DGND) | Always | Below 1 Ω |
| A-1 (SCB+) or J11-6 (DCB+) - Body ground | Always | 10 kΩ or higher |
| A-3 (SCV+) or J11-2 (DCV+) - Body ground | Always | 10 kΩ or higher |
| A-7 (SCV-) or J11-3 (DCV-) - Body ground | Always | 10 kΩ or higher |
| A-5 (SGND) or J11-7 (DGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly RH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL
Check if the same malfunction reoccurs when the side monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Malfunction does not reoccur (returns to normal) | A |
| Malfunction reoccurs | B |
A
B
Disconnect the I7 parking assist ECU connector.
Disconnect the H55 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-16 (NS+) - H55-12 (V+) | Always | Below 1 Ω |
| I7-17 (NS-) - H55-24 (V-) | Always | Below 1 Ω |
| I7-18 (NSG) - H55-23 (CGND) | Always | Below 1 Ω |
| I7-16 (NS+) or H55-12 (V+) - Body ground | Always | 10 kΩ or higher |
| I7-17 (NS-) or H55-24 (V-) - Body ground | Always | 10 kΩ or higher |
| I7-18 (NSG) or H55-23 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the navigation receiver assembly with a new or normally functioning one.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL
Check if the same malfunction reoccurs when the panoramic view monitor screen is displayed.
Malfunction does not reoccur (returns to normal).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL
for RHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL
Disconnect the I7 parking assist ECU connector.
Disconnect the H50 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-16 (NS+) - H50-12 (V+) | Always | Below 1 Ω |
| I7-17 (NS-) - H50-24 (V-) | Always | Below 1 Ω |
| I7-18 (NSG) - H50-23 (CGND) | Always | Below 1 Ω |
| I7-16 (NS+) or H50-12 (V+) - Body ground | Always | 10 kΩ or higher |
| I7-17 (NS-) or H50-24 (V-) - Body ground | Always | 10 kΩ or higher |
| I7-18 (NSG) or H50-23 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the radio and display receiver assembly with a new or normally functioning one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
Check if the same malfunction reoccurs when the panoramic view monitor screen is displayed.
Malfunction does not reoccur (returns to normal).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL
for RHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL