Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P20CF  Exhaust Aftertreatment Fuel Injector "A" Stuck Open  


DESCRIPTION

Refer to DTC P200C.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P200C

P20CF
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
PM forced regeneration AF Lambda B1S1 is less than 0.85 for a certain time while the engine is running
(1 trip detection logic)
·

Open or short in exhaust fuel addition injector assembly circuit

·

Exhaust fuel addition injector assembly

·

Fuel filter element assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system



Related Data List
DTC No. Data List
P20CF AF Lambda B1S1
Exhaust Temperature B1S2
Exhaust Temperature B1S3

MONITOR DESCRIPTION

The ECM monitors the air fuel ratio to detect whether the exhaust fuel addition injector assembly is stuck open.

If the air fuel ratio becomes too rich, the ECM determines that the exhaust fuel addition injector assembly is stuck open, illuminates the MIL and limits engine output.

HINT:

The No. 1 nitrogen oxides sensor has an air fuel ratio sensor function.


A248903E06
2.99,1.635 2.594,2.375 2.594,2.375 2.51,2.375 false 0.24,0.104 1.698,0.271 1.458,0.167 10 false Malfunction Detection: 0.229,1 1.417,1.167 1.188,0.167 10 false AF Lambda B1S1 3.854,2.031 5.042,2.198 1.188,0.167 10 false MIL Goes On 1.865,2.302 2.573,2.469 0.708,0.167 10 false Abnormal 5.604,1 6.792,1.167 1.188,0.167 10 false Normal 5.813,1.5 7,1.667 1.188,0.167 10 false P20CF Threshold 1.781,0.594 2.135,0.76 0.354,0.167 10 false Lean 1.781,1.396 2.146,1.563 0.365,0.167 10 false Rich

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P20CF)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
DTC P20CF is output A
DTC P20CF and other DTCs are output B

HINT:
·

When DTC P20CF and following DTCs are output, uncombusted fuel adhesion to the No. 1 nitrogen oxides sensor due to No. 1 nitrogen oxides sensor malfunction, fuel leaks, insufficient combustion due to parts malfunction (intake, exhaust or injection system), or an exhaust fuel addition injector assembly wiring malfunction is suspected as a cause. Therefore, diagnose the following DTCs first.

·

DTCs for the No. 1 nitrogen oxides sensor are P2200, P220E.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P2200

·

DTCs for the exhaust fuel addition injector assembly wiring malfunction is P20CD.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P20CD

·

A DTC for EGR valve flow malfunction is P0400.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P0400





A

2.CHECK FOR WHITE SMOKE (WHITE SMOKE AND ODOR)

B

10.GO TO DTC CHART
2.CHECK FOR WHITE SMOKE (WHITE SMOKE AND ODOR)
NOTICE:

If a fuel odor is noted from the white smoke during the inspection, fuel leaks from the exhaust fuel addition injector assembly are suspected.


a.

Disconnect the cable from the negative (-) battery terminal or remove the EFI-MAIN NO. 1 fuse for 1 minute or more.


b.

Start the engine and race it to 3000 rpm several times.


c.

Check for white smoke in the exhaust gas. If found, check for a fuel odor or the smell of burning oil.

Result
Result Proceed to
White smoke and a fuel odor are present. A
White smoke and a smell of burning oil are present. B
Except above C



A

3.PERFORM CONFIRMATION DRIVING PATTERN (WHITE SMOKE AND SENSOR INSPECTION)

B

11.CHECK TURBOCHARGER OIL LEAK AND WHITE SMOKE

C

7.CHECK FUEL INJECTION SYSTEM
3.PERFORM CONFIRMATION DRIVING PATTERN (WHITE SMOKE AND SENSOR INSPECTION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Exhaust / AF Lambda B1S1 ,Exhaust Temperature B1S3 and Fr-NOx Sensor A/F Active Status (SCU).


e.

Drive the vehicle until the value of Exhaust Temperature B1S3 becomes 300°C (572°F) or more to activate the Fr-NOx Sensor NOx Active Status (SCU).

HINT:

Activation of the No. 1 nitrogen oxides sensor can be checked by confirming whether the value of AF Lambda B1S1 has changed from 1.99.



f.

Check that there is no problem on driving performance such as hesitation, knocking, rough idling, insufficient power and acceleration stumbling, or white smoke in emissions.

A427297E01
5.969,1.719 6.313,1.104 6.313,1.104 6.448,1.104 true 5.188,2.823 5.344,3.073 5.344,3.073 5.479,3.073 true 1.865,1.104 4.01,1.302 2.146,0.198 10 false 1.99 0.719,1.906 2.865,2.104 2.146,0.198 10 false AF Lambda B1S1 1.865,2.469 4.01,2.667 2.146,0.198 10 false 1.0 4.281,0.708 7.156,0.927 2.875,0.219 10 false After No. 1 Nitrogen Oxides Sensor Activation 3.5,0.115 5.646,0.313 2.146,0.198 10 false No. 1 Nitrogen Oxides Sensor Starter Operation 6.594,1.01 7.156,1.292 0.563,0.281 10 false Normal 5.563,2.99 6.417,3.302 0.854,0.313 10 false Abnormal

HINT:
·

The No. 1 nitrogen oxides sensor does not operate until the vehicle has been driven for a period of time with an exhaust gas temperature of 200°C (392°F) or more.

·

Perform diagnosis when the No. 1 nitrogen oxides sensor is operating and active.

·

Normal condition in the illustration is only an example. "AF Lambda B1S1" changes depending on driving conditions. If it changes at the range more than 1.0, it is normal.



Result
Result Proceed to
There is no problem with driving performance such as hesitation, knocking, rough idling, insufficient power or acceleration stumbling, but excessive white smoke is present in the exhaust gas A
Except above B

HINT:

If white smoke is present in the exhaust gas without any driving performance problems such as hesitation, knocking, rough idling, insufficient power or acceleration stumbling, fuel injected due to a malfunction in the exhaust fuel addition injector assembly is the suspected cause of the white smoke.




A

4.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

B

7.CHECK FUEL INJECTION SYSTEM
4.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Replace the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>REMOVAL



NEXT

5.REPLACE FUEL FILTER ELEMENT ASSEMBLY
5.REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Replace the fuel filter element assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT



NEXT

6.PERFORM PM FORCED REGENERATION
6.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

Result:

PM forced regeneration completes normally.




OK

END

NG

7.CHECK FUEL INJECTION SYSTEM
7.CHECK FUEL INJECTION SYSTEM

NEXT

8.CHECK INTAKE / EXHAUST SYSTEM
8.CHECK INTAKE / EXHAUST SYSTEM

NEXT

9.CHECK AFTER TREATMENT CONTROL SYSTEM
9.CHECK AFTER TREATMENT CONTROL SYSTEM

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.GO TO DTC CHART

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CHECK TURBOCHARGER OIL LEAK AND WHITE SMOKE
a.

Check for oil leaks and white smoke from the turbocharger sub-assembly and perform any necessary repairs.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>Turbocharger Oil Leak and White Smoke

HINT:

Other than a malfunction of the turbocharger sub-assembly, exhaust valve stem oil leaks are suspected.




NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).




NEXT

END