Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL SUPPLY PUMP › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053670 1GD-FTV FUEL _0260591 FUEL SUPPLY PUMP A

1GD-FTV FUEL  FUEL SUPPLY PUMP  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe subassembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected. (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)


Hide 51405A 3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 17341K 5.REMOVE INTERCOOLER AIR HOSE (w/o Urea SCR System)

Hide 17342F 6.REMOVE NO. 2 INTERCOOLER AIR HOSE (w/o Urea SCR System)

Hide 16571C 7.REMOVE NO. 1 RADIATOR HOSE

Hide 16552B 8.REMOVE NO. 2 SUB-RADIATOR HOSE (w/ Urea SCR System)

Hide 16551B 9.REMOVE NO. 1 SUB-RADIATOR HOSE (w/ Urea SCR System)

Hide 161B0 10.REMOVE ELECTRIC WATER PUMP ASSEMBLY (w/ Urea SCR System)

Hide 16553B 11.REMOVE NO. 3 SUB-RADIATOR HOSE (w/ Urea SCR System)

Hide 16554B 12.REMOVE NO. 4 SUB-RADIATOR HOSE (w/ Urea SCR System)

Hide 16640 13.REMOVE INTERCOOLER RESERVOIR ASSEMBLY (w/ Urea SCR System)

Hide 14.DISCONNECT OIL COOLER HOSE (for Automatic Transmission)

Hide 88359 15.REMOVE VISCOUS HEATER V BELT (w/ Viscous Heater)

Hide 16470 16.REMOVE RADIATOR RESERVOIR ASSEMBLY

Hide 82123 17.DISCONNECT NO. 3 ENGINE WIRE (for Cold Area Specification Vehicles)

Hide 16711 18.REMOVE FAN SHROUD

Hide 16620 19.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 23273C 20.REMOVE NO. 2 FUEL HOSE

a.

Slide the 2 clips and remove the No. 2 fuel hose from the supply pump assembly and No. 3 nozzle leakage pipe assembly.


Hide 23271H 21.REMOVE NO. 1 FUEL HOSE

A353389

a.

Slide the 2 clips and remove the No. 1 fuel hose from the supply pump assembly and No. 2 fuel pipe.


Hide 22803 22.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

A353390

a.

Remove the fuel injection pump cover subassembly from the supply pump assembly.


Hide 23.REMOVE FUEL PUMP MOTOR WIRE

A353391

a.

Disconnect the fuel pump motor wire connector.


b.

Detach the clamp and remove the fuel pump motor wire.


Hide 11324 24.REMOVE TIMING CHAIN COVER PLATE

A344936

a.

Remove the 3 bolts and timing chain cover plate.


b.

Remove the gasket.


Hide 22100 25.REMOVE SUPPLY PUMP ASSEMBLY

A354097

NOTICE:
·

Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.

·

With SST set, do not turn the crankshaft more than a half rotation.



a.
A353392C02
1.604,1.177 1.396,1.573 1.396,1.573 1.698,1.177 true 1.281,1.573 1.552,1.865 0.271,0.292 12 true *a
*a Timing Mark


Align the timing mark of the crankshaft pulley subassembly and timing chain cover by rotating the crankshaft clockwise.


b.
A344937C01
0.5,1.51 0.75,1.51 0.75,1.51 0.844,1.698 true 1.271,2.01 1.708,2.01 false 0.708,1.99 1.021,2.146 0.313,0.156 10 false *a 0.177,1.427 0.635,1.625 0.458,0.198 10 true SST 1.75,1.938 2.208,2.135 0.458,0.198 10 true SST
*a Hold
V100135

Turn


Using SST, hold the crankshaft pulley assembly and loosen the fuel supply pump shaft nut.

SST
09213-58014  (91551-80840)
09330-00021  

NOTICE:

Do not excessively loosen the supply pump shaft nut, otherwise SST cannot be installed.


HINT:

Rotate the supply pump shaft nut once to loosen it.



c.
A353387

Loosen the 3 nuts from the supply pump assembly.

NOTICE:

Do not completely remove the nuts. Otherwise, the supply pump assembly may fall off.



d.

Install SST with 3 bolts.

SST
09241-11010  

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Install SST with the bolts included with SST.


HINT:
·
A454662C01
2.021,3.188 2.74,2.688 2.74,2.688 2.938,2.688 true 0.24,0.135 0.552,0.292 0.313,0.156 10 false *a 0.26,2.479 0.573,2.635 0.313,0.156 10 false *b 2.969,2.594 3.281,2.75 0.313,0.156 10 false *c
*a Engine Front Side
*b Engine Rear Side
*c SST Hexagonal Portion



·

Make sure that the installation direction of SST is as shown in the illustration.

·

Align the hexagonal portion of SST with the supply pump shaft nut to install SST.




e.
A344941

Remove the 2 bolts and No. 1 fuel pump bracket from the supply pump assembly and cylinder block sub-assembly.


f.
A344939C03
0.573,1.333 0.802,1.333 0.802,1.333 1.031,1.563 true 1.708,1.854 2.167,1.854 false 2.438,0.813 2.615,1.125 2.615,1.125 2.802,1.125 true 0.969,1.948 1.281,2.104 0.313,0.156 10 false *a 2.813,1.031 3.271,1.229 0.458,0.198 10 true SST 2.198,1.781 2.656,1.979 0.458,0.198 10 true SST 0.25,1.271 0.708,1.469 0.458,0.198 10 true SST
*a Hold
V100135

Turn


Install the handle to SST. While holding the crankshaft pulley assembly in place with the crankshaft holding tool, turn the handle in the counterclockwise direction to disconnect the supply pump assembly.

SST
09213-58014  (91551-80840)
09330-00021  

SST
09241-11010  


g.

Remove the 3 nuts and supply pump assembly from the timing chain case assembly.


h.
A347064

Remove the O-ring from the supply pump assembly.