Home › Engine / Hybrid System › 1GD-FTV (LUBRICATION) › OIL PUMP › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053690 1GD-FTV LUBRICATION _0260709 OIL PUMP A

1GD-FTV LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

Make sure foreign matter does not enter the fuel path.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.



PROCEDURE

Hide 12633 2.REMOVE NO. 3 ENGINE COVER BRACKET (w/o Urea SCR System)

Hide 12632 3.REMOVE NO. 2 ENGINE COVER BRACKET (w/o Urea SCR System)

Hide 4.REMOVE ENGINE WIRE

Hide 77246C 5.REMOVE FUEL MAIN TUBE SUPPORT (w/ Urea SCR System)

Hide 17360A 6.REMOVE AIR TUBE ASSEMBLY (w/o Urea SCR System)

Hide 26100G 7.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 16278 8.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 25625 17.REMOVE EGR VALVE BRACKET

Hide 16206B 19.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 25601 21.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 16209 23.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 25800 24.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 11409 25.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 27.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 22803 29.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 23243B 30.REMOVE FUEL PUMP MOTOR WIRE

Hide 23273H 31.REMOVE NO. 2 FUEL HOSE

Hide 23271H 32.REMOVE NO. 1 FUEL HOSE

Hide 23804D 33.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY

Hide 23804C 35.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 23770 36.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 27148A 38.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23760 40.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 82715 41.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23701 42.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 88431 44.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 12261 45.REMOVE PCV HOSE (except Cold Area Specification Vehicles)

Hide 12229 46.REMOVE PCV PIPE (for Cold Area Specification Vehicles)

Hide 47.REMOVE WATER BY-PASS HOSE (w/ Urea SCR System)

Hide 16282 48.REMOVE NO. 5 WATER BY-PASS HOSE

Hide 16281 49.REMOVE NO. 4 WATER BY-PASS HOSE

Hide 17168 51.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 89467B 52.REMOVE AIR FUEL RATIO SENSOR (w/o Urea SCR System)

Hide 17167 53.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 89463C 55.DISCONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Urea SCR System)

Hide 17118 56.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY

Hide 25051 58.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 89463C 59.REMOVE NO. 1 NITROGEN OXIDES SENSOR (w/ Urea SCR System)

Hide 16268 61.REMOVE NO. 1 WATER BY-PASS PIPE

Hide 16284 62.REMOVE NO. 1 AND NO. 2 TURBO WATER HOSE

Hide 87101 63.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

Hide 15407 66.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 17201 67.REMOVE TURBOCHARGER SUB-ASSEMBLY

Hide 16207 68.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16304 69.REMOVE WATER OUTLET SUB-ASSEMBLY

Hide 16321 70.REMOVE WATER INLET

Hide 16331A 71.REMOVE THERMOSTAT

Hide 16603 72.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A339577

Remove the bolt and No. 1 idler pulley sub-assembly from the generator bracket sub-assembly.


Hide 16620 73.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A339579

Remove the 3 bolts and V-ribbed belt tensioner assembly from the timing chain cover sub-assembly.


Hide 88451B 74.REMOVE VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

Hide 16575C 77.REMOVE NO. 1 WATER HOSE CLAMP BRACKET

Hide 12501 79.REMOVE GENERATOR BRACKET SUB-ASSEMBLY

Hide 23670 80.REMOVE INJECTOR ASSEMBLY

Hide 23682 81.REMOVE NOZZLE HOLDER GASKET

Hide 11401G 82.REMOVE CAMSHAFT POSITION SENSOR

Hide 11201 83.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A424542C01
0,0 0,0 false
V100135

Bolt
V100136

Nut
V100137

Nozzle Holder Clamp Seat


Remove the 14 bolts, 4 nozzle holder clamp seats, 2 nuts and cylinder head cover sub-assembly from the cylinder head sub-assembly.


b.
A339581E02
2.5,0.281 2.427,0.281 2.427,0.281 2.25,0.552 true 1.042,0.323 0.958,0.323 0.958,0.323 0.781,0.594 true 1.177,1.208 1.094,1.208 1.094,1.208 0.885,1.375 true 0.313,1.802 0.396,1.802 0.396,1.802 0.708,1.229 true 2.563,0.188 2.802,0.385 0.24,0.198 10 false *1 1.104,0.24 1.354,0.427 0.25,0.188 10 false *3 1.229,1.135 1.479,1.323 0.25,0.188 10 true *3 0.115,1.708 0.354,1.885 0.24,0.177 10 false *2

Remove the cylinder head cover gasket, No. 2 cylinder head cover gasket and 2 camshaft bearing cap oil hole gaskets from the cylinder head cover sub-assembly.

Text in Illustration
*1 Cylinder Head Cover Gasket
*2 No. 2 Cylinder Head Cover Gasket
*3 Camshaft Bearing Cap Oil Hole Gasket


Hide 12102A 84.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A339699

Remove the 2 nuts and 11 bolts.

Text in Illustration
V100135

Bolt
V100136

Nut


b.
A120816

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and No. 2 oil pan sub-assembly, cut off the applied sealer and remove the No. 2 oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the contact surfaces of the oil pan sub-assembly and No. 2 oil pan sub-assembly.

·

Be careful not to damage the oil pan sub-assembly flange.




Hide 89491 85.REMOVE ENGINE OIL LEVEL SENSOR

Hide 12101 86.REMOVE OIL PAN SUB-ASSEMBLY

a.
A339700

Remove the 2 nuts and 23 bolts.

Text in Illustration
V100135

Bolt
V100136

Nut


b.
A120816

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and cylinder block sub-assembly, cut off the applied sealer and remove the oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the contact surfaces of the oil pan sub-assembly and cylinder block sub-assembly.

·

Be careful not to damage the cylinder block sub-assembly flange.




Hide 87.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 88.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 11324 89.REMOVE TIMING CHAIN COVER PLATE

Hide 22815A 91.REMOVE INJECTION PUMP INSULATOR

Hide 11302 92.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A339584

Remove the 20 bolts from the timing chain cover sub-assembly.


b.

Using a screwdriver wrapped in protective tape, remove the timing chain cover sub-assembly by prying the points in the illustration.

A339585E02
6.583,0.198 6.458,0.198 6.458,0.198 6.177,0.677 true 6.188,2.427 6.063,2.427 6.063,2.427 5.615,1.927 true 0.594,1.281 0.719,1.281 0.719,1.281 0.99,0.656 true 6.635,0.104 6.896,0.292 0.26,0.188 10 false *a 6.25,2.333 6.49,2.521 0.24,0.188 10 false *a 0.375,1.177 0.635,1.375 0.26,0.198 10 false *a

Text in Illustration
*a Protective Tape - -

NOTICE:

Do not damage the contacting surfaces of the timing chain cover sub-assembly and timing chain case assembly.



c.
A339592

Remove the timing chain case gasket from the timing chain case assembly.


Hide 11303A 93.REMOVE FRONT CRANKSHAFT OIL SEAL

a.
A339586E02
2.469,0.24 2.302,0.24 2.302,0.24 1.479,0.938 true 0.646,1.219 1.271,1.219 true 2.542,0.156 2.792,0.344 0.25,0.188 10 false *a 0.406,1.125 0.656,1.323 0.25,0.198 10 false *b

Using a screwdriver and wooden block, pull out the front crankshaft oil seal.

Text in Illustration
*a Protective Tape
*b Wooden Block

NOTICE:

Do not damage the surface of the front crankshaft oil seal press fit hole.



Hide 94.INSPECT BACKLASH OF OIL PUMP GEAR TO OIL PUMP DRIVE GEAR

a.
A339596

Using a dial indicator, measure the backlash.

Standard gear backlash:

0.02 to 0.3 mm (0.000787 to 0.0118 in.)


Maximum gear backlash:

0.42 mm (0.0165 in.)


If the gear backlash is more than the maximum, replace the timing chain case assembly or oil pump drive gear.


Hide 13519 95.REMOVE OIL PUMP DRIVE GEAR

a.
A339595

Remove the oil pump drive gear from the crankshaft.


Hide 13560A 96.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 11991A 97.REMOVE NO.1 BALANCE SHAFT THRUST PLATE

Hide 98.REMOVE BALANCE SHAFT TIMING SPROCKET, BALANCE SHAFT GEAR SUB-ASSEMBLY AND NO. 3 CHAIN SUB-ASSEMBLY

Hide 13566B 99.REMOVE TIMING CHAIN GUIDE

Hide 13550 100.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 101.REMOVE NO. 2 CHAIN TENSIONER SLIPPER

Hide 13562 102.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13507 103.REMOVE NO. 2 CHAIN SUB-ASSEMBLY

Hide 13540 104.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 105.REMOVE NO. 1 CHAIN TENSIONER SLIPPER

Hide 13561 106.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13506 107.REMOVE CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY

Hide 13523 108.REMOVE CAMSHAFT TIMING SPROCKET

Hide 11310 109.REMOVE TIMING CHAIN CASE ASSEMBLY

a.
A339590

Remove the 15 bolts from the timing chain case assembly.


b.

Using a screwdriver wrapped in protective tape, remove the timing chain case assembly by prying the points in the illustration.

A339591E01
6.792,0.135 6.646,0.135 6.646,0.135 6.375,0.479 true 6.448,2.448 6.302,2.448 6.302,2.448 5.823,2.083 true 0.615,0.76 0.76,0.76 0.76,0.76 1.156,1.219 true 6.854,0.031 7.104,0.208 0.25,0.177 10 false *a 6.51,2.354 6.771,2.542 0.26,0.188 10 false *a 0.385,0.656 0.656,0.865 0.271,0.208 10 false *a

Text in Illustration
*a Protective Tape - -

NOTICE:

Do not damage the contacting surfaces of the timing chain case assembly, cylinder head sub-assembly and cylinder block sub-assembly.



c.
A339593

Remove the 4 O-rings from the cylinder head sub-assembly and cylinder block sub-assembly.


d.
A388469

Remove the gasket from the timing chain case assembly.