Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING › from 2020.08
RM27T0E _59 Vehicle Exterior _053743 SLIDING ROOF / CONVERTIBLE _0261243 SLIDING ROOF HOUSING A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING  INSTALLATION  


PROCEDURE

Hide 63203F 1.INSTALL SLIDING ROOF HOUSING SUB-ASSEMBLY

a.

Temporarily install the sliding roof housing sub-assembly with the 4 bolts (vehicle body side) and 8 nuts.


b.

Tighten the 8 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Tighten the 4 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

B236462


d.

Connect the 4 drain hoses.


Hide 63201G 2.INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY

a.
B236460

Using a T25 "TORX" driver, temporarily install the sliding roof glass sub-assembly with the 4 screws.


b.

Perform a level check.

i.

Check the difference in the level between the roof panel and upper surface of the weatherstrip labeled "a" when the sliding roof glass is fully closed.

B236479E02
5.198,0.823 5.365,0.99 0.167,0.167 10 false *a 4.438,1.281 4.594,1.458 0.156,0.177 10 false a 2.021,1.885 2.177,2.063 0.156,0.177 10 false A 2.302,1.885 2.458,2.063 0.156,0.177 10 false A 2.594,1.875 2.75,2.052 0.156,0.177 10 false B 2.865,1.885 3.021,2.063 0.156,0.177 10 false B 2.469,2.333 2.625,2.51 0.156,0.177 10 true D 2.25,1.365 2.406,1.542 0.156,0.177 10 true C 2.25,1.115 2.406,1.313 0.156,0.198 10 true C 2.646,2.563 2.802,2.76 0.156,0.198 10 true D

Text in Illustration
*a Even - -

Standard:
Area Specified Condition
A - A -2.0 to 1.0 mm (-0.0787 to 0.0394 in.)
B - B -1.0 to 2.0 mm (-0.0394 to 0.0787 in.)
C - C -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
D - D -1.0 to 1.5 mm (-0.0394 to 0.0591 in.)


HINT:

"+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.



ii.

Perform a gap check.

Check the gap between the roof panel and roof glass.

NOTICE:

The gap must be even all around.




c.
B244002

Using a T25 "TORX" driver, tighten the 4 screws.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 3.CHECK FOR WATER LEAK

a.

After adjusting the sliding roof glass sub-assembly, check for water leakage into the vehicle interior.

If there are any leaks, readjust the sliding roof glass sub-assembly.


Hide 63218M 4.INSTALL SLIDING ROOF SIDE GARNISH LH

B236459

a.

Attach the 5 claws to install the sliding roof side garnish LH.


Hide 63217K 5.INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 86117A 6.INSTALL TELEVISION DISPLAY BRACKET A (w/ Rear Seat Entertainment System)

a.
B589965

Install the television display bracket A with the 4 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

Text in Illustration
V100136

Front Side


Hide 86680A 7.INSTALL TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)

Hide 88566T 8.INSTALL REAR NO. 3 ROOF AIR DUCT (for Dual Air Conditioning System)

Hide 88566V 9.INSTALL REAR NO. 5 ROOF AIR DUCT (for Dual Air Conditioning System)

Hide 62180A 10.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

Hide 62170A 11.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 63310 12.INSTALL ROOF HEADLINING ASSEMBLY (for 3 Door)

Hide 63310 13.INSTALL ROOF HEADLINING ASSEMBLY (for 5 Door)

Hide 14.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 15. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART