The particulate matter sensor is installed in the center exhaust pipe assembly to detect the PM value.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P24AE12 | Particulate Matter Sensor Circuit High Circuit Short to Battery | Open or short in particulate matter sensor circuit for 10 seconds or more
(2 trip detection logic) |
Particulate matter sensor | Comes on | DTC stored | SAE Code: P24B1 |
| P24AE14 | Particulate Matter Sensor Circuit Low Circuit Short to Ground or Open | Open or short in particulate matter sensor circuit for 10 seconds or more
(2 trip detection logic) |
Particulate matter sensor | Comes on | DTC stored | SAE Code: P24B0 |
| P24AE96 | Particulate Matter Sensor Circuit Range/Performance Component Internal Failure | Particulate matter sensor out of range for 3 seconds or more
(2 trip detection logic) |
Particulate matter sensor | Comes on | DTC stored | SAE Code: P24AF |
| P24B301 | Particulate Matter Sensor Heater Control Circuit/Open General Electrical Failure | Malfunction in particulate matter sensor circuit for 10 seconds or more
(2 trip detection logic) |
Particulate matter sensor | Comes on | DTC stored | SAE Code: P24B3 |
| P24C601 | Particulate Matter Sensor Temperature Circuit General Electrical Failure | Malfunction in particulate matter sensor temperature sensor for 10 seconds or more
(2 trip detection logic) |
Particulate matter sensor | Comes on | DTC stored | SAE Code: P24C6 |
| P24D000 | Particulate Matter Sensor Supply Voltage Circuit Low | Low power supply to particulate matter sensor circuit for 10 seconds or more
(2 trip detection logic) |
·
Particulate matter sensor ·
NOX PM relay ·
Harness or connector |
Comes on | DTC stored | SAE Code: P24D0 |
| DTC No. | Data List |
|---|---|
| P24AE12
P24AE14 P24AE96 P24B301 P24C601 P24D000 |
·
PM Sensor Output Current ·
Status of PM Sensor IDE Circuit ·
Status of PM Sensor IDE (+ Side) ·
Status of PM Sensor Temperature ·
Status of PM Sensor IDE (- Side) ·
Status of PM Sensor Heater ON Malfunction ·
Status of PM Sensor Heater OFF Malfunction |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P24AE12
P24AE14 P24AE96 P24B301 P24C601 P24D000 |
Engine switch on (IG) and wait for 10 seconds or more |
Refer to DTC U029D87.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>U029D87
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P24D000 is output | A |
| DTC P24AE12, P24AE14, P24AE96, P24B301, P24C601, P24D000 is output | B |
| DTC P24AE12 or P24AE14, P24AE96, P24B301, P24C601, P24D000 and other DTCs are output* | C |
*: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.
A
B
C
Inspect the No. 1 integration relay (NOX PM relay).
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY (w/ Urea SCR System)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the particulate matter sensor connector.
Remove the NOX PM relay from the No.1 Integration Relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1W-11 - s8-1 (BATT) | Always | Below 1 Ω |
| 1W-11 - s8-1 (BATT) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for 30 seconds.
Turn the engine switch on (IG) and wait for 10 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the No. 1 integration relay (NOX PM relay).
| Proceed to |
|---|
| NEXT |
NEXT
Replace the particulate matter sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>PARTICULATE MATTER SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT