Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  Starter Signal Circuit  


DESCRIPTION

w/o Stop and Start System

While the engine is being cranked, the starter signal is also sent to terminal STA of the ECM. The starter signal mainly performs engine control when the engine is started.

w/ Stop and Start System

While the engine is being cranked, the ECM detects the starter drive signal (STA2 signal) from the engine stop and start ECU as the starter operation signal (STA signal) to perform engine control when the engine is started.

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Read Starter Count before replacing the engine stop and start ECU, perform the replacement procedure, and then write Starter Count to the newly installed engine stop and start ECU.

·

When replacing the engine stop and start ECU or the air conditioning amplifier assembly, initialize and learn the engine stop and start ECU air conditioning information.

·

When replacing the engine stop and start ECU or airbag ECU assembly (G sensor), initialize and learn the engine stop and start ECU G sensor zero point learned information.



HINT:

w/o Stop and Start System

This procedure is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to the problem symptoms table.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>PROBLEM SYMPTOMS TABLE


PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH STOP AND START SYSTEM
a.

Confirm the vehicle specifications.

Result:
Proceed to
w/ Stop and Start System
w/o Stop and Start System




w/o Stop and Start System

2.READ VALUE USING GTS (STARTER SIGNAL)

w/ Stop and Start System

5.CHECK WHETHER ENGINE CAN BE CRANKED
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Primary / Starter SW.


d.

Check the value displayed on the GTS when the engine switch is turned the on (IG) and START positions.

OK:
Switch Condition Starter SW
ON OFF
START ON



Result:
Proceed to
OK
NG (for Manual transmission)
NG (for Automatic transmission)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG (for Manual transmission)

3.CHECK HARNESS AND CONNECTOR (ECM - CLUTCH SWITCH ASSEMBLY)

NG (for Automatic transmission)

4.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (ECM - CLUTCH SWITCH ASSEMBLY)
HINT:
·

*1: for LHD

·

*2: for RHD



a.

Disconnect the ECM connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G184-22 (STA) - A40-1*1 Always Below 1 Ω
G184-22 (STA) - r1-1*2 Always Below 1 Ω
G184-22 (STA) or A40-1*1 - Body ground and other terminals Always 10 kΩ or higher
G184-22 (STA) or r1-1*2 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G184-22 (STA) - C156-5 (L) Always Below 1 Ω
G184-22 (STA) or C156-5 (L) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.


Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

6.READ VALUE USING GTS (STARTER SIGNAL)

B

17.READ VALUE USING GTS (STARTER SIGNAL)
6.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Primary / Starter SW.


d.

Check the value displayed on the GTS when the engine switch is on (IG) and the engine stars.


OK:
Switch Condition Starter SW
ON OFF
START ON


Result:
Proceed to
OK
NG



OK

7.INSPECT ST NO. 2 RELAY

NG

GO TO STOP AND START SYSTEM (STARTER SIGNAL CIRCUIT)

7.INSPECT ST NO. 2 RELAY

Result:
Proceed to
OK
NG



OK

8.INSPECT ST RELAY

NG

REPLACE ST NO. 2 RELAY

8.INSPECT ST RELAY

Result:
Proceed to
OK
NG



OK

9.INSPECT STARTER ASSEMBLY

NG

REPLACE ST RELAY

9.INSPECT STARTER ASSEMBLY

Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - STARTER ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 2 relay terminal 3 - D14-2 (SL2) Always Below 1 Ω
ST NO. 2 relay terminal 3 - D15-1 (ST) Always Below 1 Ω
ST NO. 2 relay terminal 3 or D14-2 (SL2) - Body ground and other terminals Always 10 kΩ or higher
ST NO. 2 relay terminal 3 or D15-1 (ST) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - ECM)
a.

Remove the ST NO. 2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Disconnect the engine stop and start ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 2 relay terminal 2 - G184-22 (STA) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BODY GROUND)
a.
A475000C01
2.156,0.292 2.469,0.49 0.313,0.198 10 false *1 0.51,1.115 0.823,1.313 0.313,0.198 10 false *a
*1 Engine Room Relay Block and Junction Block Assembly
*a ST NO. 2 Relay Terminal


Remove the ST NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 2 relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (BATTERY - ST NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (BATTERY - ST NO. 2 RELAY)
a.
A475000C02
2.156,0.292 2.469,0.49 0.313,0.198 10 false *1 0.448,1.167 0.76,1.365 0.313,0.198 10 false *a
*1 Engine Room Relay Block and Junction Block Assembly
*a ST NO. 2 Relay Terminal


Remove the ST NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST NO. 2 relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (BATTERY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (BATTERY - ST RELAY)
a.
A413699C05
0.323,0.302 0.635,0.5 0.313,0.198 10 false *1 2.792,1.406 3.104,1.604 0.313,0.198 10 false *a
*1 Engine Room Relay Block and Junction Block Assembly
*a ST Relay Terminal


Remove the ST relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)
a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 3 - C59-1 (SL1) Always Below 1 Ω
ST relay terminal 3 or C59-1 (SL1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.
A413699C06
0.323,0.302 0.635,0.5 0.313,0.198 10 false *1 2.792,1.406 3.104,1.604 0.313,0.198 10 false *a
*1 Engine Room Relay Block and Junction Block Assembly
*a ST Relay Terminal


Remove the ST relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Primary / Starter SW.


d.

Check the value displayed on the GTS when the engine switch is turned the on (IG) and START positions.


OK:
Switch Condition Starter SW
ON OFF
START ON


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 2 RELAY - ECM)