Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › from 2020.08
RM27T0E _51 Engine / Hybrid System _053665 1GD-FTV ENGINE MECHANICAL _0260526 CYLINDER HEAD GASKET A

1GD-FTV ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 1 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 11310 2.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 13801 3.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 11101 5.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A344477E02
3.063,1.813 3.219,1.99 0.156,0.177 10 false 1 0.396,0.229 0.552,0.406 0.156,0.177 10 false 2 3.083,0.219 3.24,0.396 0.156,0.177 10 true 3 0.385,1.833 0.542,2.01 0.156,0.177 10 true 4 2.406,0.198 2.563,0.375 0.156,0.177 10 false 5 1.052,1.844 1.208,2.021 0.156,0.177 10 false 6 2.406,1.844 2.563,2.021 0.156,0.177 10 false 7 1.063,0.198 1.219,0.375 0.156,0.177 10 false 8 1.729,1.844 1.885,2.021 0.156,0.177 10 false 9 1.698,0.188 1.865,0.365 0.167,0.177 10 false 10

Uniformly loosen the 10 cylinder head set bolts in several passes in the sequence shown in the illustration. Then remove the 10 cylinder head set bolts and 6 cylinder head set bolt spacers.

NOTICE:
·

Cylinder head sub-assembly warpage or cracking could result from removing bolts in the incorrect order.

·

Be careful not to drop the cylinder head set bolt spacers into the cylinder head sub-assembly.




b.

Lift the cylinder head sub-assembly from the ring pins on the cylinder block sub-assembly, and place the cylinder head sub-assembly on wooden blocks on a bench.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and cylinder block sub-assembly.


HINT:

If the cylinder head sub-assembly is difficult to remove, use a screwdriver to pry between the cylinder head sub-assembly and cylinder block sub-assembly.



Hide 11115 6.REMOVE CYLINDER HEAD GASKET

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.