Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › CAMSHAFT › from 2020.08
RM27T0E _51 Engine / Hybrid System _053665 1GD-FTV ENGINE MECHANICAL _0260525 CAMSHAFT A

1GD-FTV ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 1 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 11382C 3.REMOVE CAMSHAFT OIL SEAL RETAINER

Hide 16278 4.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 12633 5.REMOVE NO. 3 ENGINE COVER BRACKET (w/o Urea SCR System)

Hide 12632 6.REMOVE NO. 2 ENGINE COVER BRACKET (w/o Urea SCR System)

Hide 12261 8.REMOVE PCV HOSE (except Cold Area Specification Vehicles)

Hide 12203 9.REMOVE PCV PIPE SUB-ASSEMBLY (for Cold Area Specification Vehicles)

Hide 16281 10.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)

Hide 16282 11.DISCONNECT NO. 5 WATER BY-PASS HOSE (w/ DPF)

Hide 23295D 12.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)

Hide 17168 13.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)

Hide 89481B 14.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)

Hide 89425 15.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 89463C 20.DISCONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Urea SCR System)

Hide 77246C 21.REMOVE FUEL MAIN TUBE SUPPORT

Hide 26100G 22.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 89421C 24.REMOVE TURBO PRESSURE SENSOR

Hide 25625 25.REMOVE EGR VALVE BRACKET

Hide 16206B 27.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16209 28.DISCONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 25601 29.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 31.REMOVE NO. 1 EGR COOLER WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 32.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23760 34.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 35.REMOVE NO. 1 INJECTION PIPE SUB-ASSEMBLY AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23670 36.REMOVE INJECTOR ASSEMBLY

Hide 23682 37.REMOVE NOZZLE HOLDER GASKET

Hide 11401G 38.REMOVE CAMSHAFT POSITION SENSOR

Hide 11201 39.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 40.SET NO. 1 CYLINDER TO TDC / COMPRESSION

a.
U169474E02
1.594,1.365 1.969,1.823 1.969,1.823 2.167,1.823 true 1.49,1.323 1.115,0.865 1.115,0.865 0.927,0.865 true 0.99,3.198 0.615,2.74 0.615,2.74 0.427,2.74 false 2.219,3.198 2.583,2.74 2.583,2.74 2.781,2.74 false 1.01,3.302 1.01,3.677 false 2.219,3.292 2.219,3.677 false 0.729,0.76 1,0.979 0.271,0.219 10 true *a 2.188,1.74 2.656,1.958 0.469,0.219 10 false *a 0.219,2.646 0.49,2.865 0.271,0.219 10 false *b 2.781,2.646 3.052,2.865 0.271,0.219 10 false *b 0.927,3.677 1.156,3.896 0.229,0.219 10 false *a 2.125,3.677 2.354,3.896 0.229,0.219 10 false *a

Align the timing mark of the crankshaft pulley and timing chain cover by rotating the crankshaft clockwise.

Text in Illustration
*a Timing Mark
*b Paint Mark


b.

Make sure that the timing mark of the camshaft timing sprocket is at the top.

HINT:

If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark is at the top (set the No. 1 piston to TDC/ compression).



c.

Place paint marks on the No. 2 chain sub-assembly.


Hide 13566B 41.REMOVE TIMING CHAIN GUIDE

a.
A345766

Remove the bolt and timing chain guide from the cylinder head sub-assembly.


Hide 42.REMOVE CAMSHAFT

a.
A345767

Remove the oil pump relief valve plug and gasket from timing chain cover.


b.
A345768E02
1.792,0.844 2.5,0.844 true 1.74,1.719 2.448,1.719 true 2.521,0.75 2.708,0.938 0.188,0.188 10 true *a 2.479,1.625 2.667,1.813 0.188,0.188 10 true *b

Insert a pin into stopper plate hole of the No. 2 chain tensioner assembly and lock the No. 2 chain tensioner assembly.

Text in Illustration
*a Stopper Plate
*b Pin


c.
A345769E02
1.969,0.615 2.906,0.615 true 0.49,2.906 1.427,2.906 true 2.938,0.531 3.156,0.823 0.219,0.292 10 false *1 0.271,2.823 0.49,3.115 0.219,0.292 10 false *2

Hold the hexagonal portion of the camshaft with a wrench and loosen the 2 bolts from the No. 1 camshaft and No. 2 camshaft.

CAUTION:

Be careful not to damage the cylinder head sub-assembly with the wrench.


Text in Illustration
*1 No. 1 Camshaft
*2 No. 2 Camshaft


d.
A343548

Remove the 2 bolts and No. 3 camshaft bearing cap from the cylinder head sub-assembly.


e.
A345770E02
0.083,0.208 0.188,0.365 0.104,0.156 10 true 1 0.073,1.76 0.177,1.917 0.104,0.156 10 true 2 0.052,0.656 0.188,0.813 0.135,0.156 10 true 3 0.042,1.333 0.177,1.49 0.135,0.156 10 true 4 0.5,1.708 0.677,1.865 0.177,0.156 10 true 11 0.594,0.865 0.771,1.021 0.177,0.156 10 true 12 1.073,1.135 1.25,1.292 0.177,0.156 10 true 10 1.281,0.875 1.458,1.031 0.177,0.156 10 true 20 1.208,0.333 1.333,0.51 0.125,0.177 10 true 9 1.188,1.688 1.365,1.844 0.177,0.156 10 true 19 1.729,1.094 1.906,1.25 0.177,0.156 10 true 18 1.875,0.344 2.063,0.542 0.188,0.198 10 true 17 1.948,0.875 2.146,1.031 0.198,0.156 10 true 16 1.906,1.698 2.083,1.854 0.177,0.156 10 true 15 2.396,1.104 2.573,1.26 0.177,0.156 10 false 14 2.552,0.344 2.75,0.521 0.198,0.177 10 true 13 3.198,0.344 3.354,0.531 0.156,0.188 10 true 5 3.208,1.104 3.344,1.292 0.135,0.188 10 true 6 2.583,1.698 2.729,1.854 0.146,0.156 10 true 7 2.625,0.875 2.75,1.031 0.125,0.156 10 true 8

Using several steps, and remove the 20 bolt, No. 1 camshaft bearing cap and 8 No. 2 camshaft bearing caps from the cylinder head sub-assembly.


f.
A345771

Raise the No. 1 camshaft and remove the bolt from the No. 1 camshaft.


g.

Raise the No. 2 camshaft and remove the bolt from the No. 2 camshaft.


h.
A345772

Remove the No. 2 camshaft from the camshaft timing sprocket.


i.
A345774

Remove the camshaft timing sprocket from the No. 2 chain sub-assembly.


j.
A345773

Remove the No. 1 camshaft from the camshaft timing sprocket.


k.
A345775

Remove the camshaft timing sprocket from the No. 2 chain sub-assembly.


l.
A345776

Suspend the No. 2 chain sub-assembly with a string or equivalent.

HINT:

Be careful not to drop the No. 2 chain sub-assembly inside the timing chain cover assembly.