Check the radio automatic station search function by activating it.
Automatic station search function stops on a station.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
NG
Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.
Optional components are not installed.
Do not remove optional components without the permission of the customer.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Preparation for check
Disconnect the radio and display receiver assembly antenna connector.
Check for noise
Turn the ignition switch to ON with the radio and display receiver assembly connector connected.
Turn the radio and display receiver assembly on and tune into AM mode.
Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.
Noise can be heard from the speakers.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
Disconnect the radio and display receiver assembly antenna connector.
| *a | Component without harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A-5 (ANT+) - Body ground | Ignition switch ACC
Radio switch on and FM or AM selected |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
Inspect the quarter window assembly (window glass antenna wire).
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>WINDOW GLASS ANTENNA WIRE>REPAIR
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for 5 Doors | A |
| for 3 Doors | B |
A
B
| *a | Front view of wire harness connector
(to Wire Harness) |
| *b | Front view of wire harness connector
(to Holder Antenna Assembly) |
| *c | Front view of wire harness connector
(to Holder Antenna Assembly) |
| *d | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the wire harness.
Disconnect the antenna connector from the holder antenna assembly.
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 - C-3 | Always | Below 1 Ω |
| B-1a - C-3a | Always | Below 1 Ω |
| B-2 - C-2 | Always | Below 1 Ω |
| B-2a - C-2a | Always | Below 1 Ω |
| B-3 - C-1 | Always | Below 1 Ω |
| D-1 - G-1 | Always | Below 1 Ω |
| D-1a - G-1a | Always | Below 1 Ω |
| B-1 - Body ground | Always | 10 kΩ or higher |
| B-2 - Body ground | Always | 10 kΩ or higher |
| B-3 - Body ground | Always | 10 kΩ or higher |
| D-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the radio and display receiver assembly.
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-3 (AMFM) - B-1 | Always | Below 1 Ω |
| A-4 - B-1a | Always | Below 1 Ω |
| A-1 (FMSUB) - B-2 | Always | Below 1 Ω |
| A-2 - B-2a | Always | Below 1 Ω |
| A-5 (+B) - B-3 | Always | Below 1 Ω |
| B-4 - Body ground | Always | 10 kΩ or higher |
| B-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 5 Doors:
*2: for 3 Doors:
| *A | for 5 Doors |
| *B | for 3 Doors |
| *a | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Quarter Window Assembly RH [window glass antenna wire]) |
| *c | Front view of wire harness connector
(to Quarter Window Assembly LH [window glass antenna wire]) |
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Disconnect the antenna connector from the quarter window assembly RH (window glass antenna wire).*1
Disconnect the antenna connector from the quarter window assembly LH (window glass antenna wire).*2
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G-1 - H-1 | Always | Below 1 Ω |
| G-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the holder antenna assembly with a new or known good one and check if radio broadcasts can be received normally.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL
Radio broadcasts can be received normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
| *a | Front view of wire harness connector
(to Wire Harness) |
| *b | Front view of wire harness connector
(to Holder Antenna Assembly) |
| *c | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the wire harness.
Disconnect the antenna connector from the holder antenna assembly.
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 - C-9 | Always | Below 1 Ω |
| B-1a - C-9a | Always | Below 1 Ω |
| B-2 - C-8 | Always | Below 1 Ω |
| B-2a - C-8a | Always | Below 1 Ω |
| B-3 - C-3 | Always | Below 1 Ω |
| C-7 - G-1 | Always | Below 1 Ω |
| C-7a - G-1a | Always | Below 1 Ω |
| B-1 - Body ground | Always | 10 kΩ or higher |
| B-2 - Body ground | Always | 10 kΩ or higher |
| B-3 - Body ground | Always | 10 kΩ or higher |
| C-7 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG