Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0260748 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Distance Control Switch Circuit  


DESCRIPTION

The vehicle-to-vehicle distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The vehicle-to-vehicle distance control switch is installed in the steering pad switch assembly. The vehicle-to-vehicle distance set value can be changed by operating the vehicle-to-vehicle distance control switch while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.

WIRING DIAGRAM

C384959E03
1.469,0.688 2.573,1.458 1.104,0.771 10 false Vehicle-to-vehicle Distance Control Switch 0.823,2.615 2.896,3.219 2.073,0.604 10 false Steering Pad Switch Assembly 3.115,2.573 4.854,2.875 1.74,0.302 10 false Spiral Cable Sub-assembly 5.229,1.021 7.042,1.677 1.813,0.656 10 false Forward Recognition Camera 3,2 3.313,2.198 0.313,0.198 10 false z16 3,0.542 3.313,0.74 0.313,0.198 10 false z16 4.167,0.552 4.573,0.823 0.406,0.271 10 false G208 4.167,2.01 4.688,2.302 0.521,0.292 10 false G208 5.229,0.833 5.615,1.042 0.385,0.208 10 false W22 3.76,0.427 4.375,0.625 0.615,0.198 10 false DIST 2.531,0.427 3.146,0.625 0.615,0.198 10 false DIST 2.531,1.885 3.146,2.083 0.615,0.198 10 false ECC 3.781,1.885 4.396,2.083 0.615,0.198 10 false ECC 6.073,0.542 6.688,0.74 0.615,0.198 10 false LKSW 3.073,0.323 3.229,0.521 0.156,0.198 10 false 4 3.083,1.781 3.365,1.979 0.281,0.198 10 false 7 4.271,0.313 4.552,0.573 0.281,0.26 10 false 12 4.313,1.781 4.469,1.979 0.156,0.198 10 false 2 5.875,0.427 6.031,0.625 0.156,0.198 10 false 3 5.448,1.885 5.76,2.083 0.313,0.198 10 false *1 5.365,2.177 5.677,2.375 0.313,0.198 10 false *2 6.063,2.01 6.729,2.292 0.667,0.281 10 false ECCS*1 5.813,1.885 6.125,2.083 0.313,0.198 10 false 21 6.188,2.479 6.802,2.677 0.615,0.198 10 false G181 6.198,2.646 6.656,2.844 0.458,0.198 10 false ECM 0.323,3.385 2.469,3.583 2.146,0.198 10 false *1: for 2TR-FE 1.969,3.385 4.115,3.583 2.146,0.198 10 false *2: except 2TR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the ECM, refer to Service Bulletin.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

When replacing the forward recognition camera, replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, it is necessary to perform forward recognition camera adjustment.

HINT:

Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)




PROCEDURE

1.READ VALUE USING GTS (VEHICLE-TO-VEHICLE DISTANCE CONTROL SWITCH)
a.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise2 > Data List
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Vehicle-to-vehicle Distance Control Switch Vehicle-to-vehicle distance control switch signal / ON or OFF ON: Vehicle-to-vehicle distance control switch pushed
OFF: Vehicle-to-vehicle distance control switch not pushed
-

OK:

The value of the Data List item changes according to the operation of the vehicle-to-vehicle distance control switch.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING WHEEL>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING WHEEL>INSTALLATION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Result Proceed to
OK (except 2TR-FE) A
OK (for 2TR-FE) B
NG C



A

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA AND BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA AND ECM)

C

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA AND BODY GROUND)
a.

Disconnect the G208 spiral cable sub-assembly connector.


b.

Disconnect the W22 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G208-12 (DIST) - W22-3 (LKSW) Always Below 1 Ω
G208-2 (ECC) - Body ground Always Below 1 Ω
G208-12 (DIST) or W22-3 (LKSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA AND ECM)
a.

Disconnect the G208 spiral cable sub-assembly connector.


b.

Disconnect the W22 forward recognition camera connector.


c.

Disconnect the G181 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G208-12 (DIST) - W22-3 (LKSW) Always Below 1 Ω
G208-2 (ECC) - G181-21 (ECCS) Always Below 1 Ω
G208-12 (DIST) or W22-3 (LKSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR