Home › Drivetrain › VF4BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2020.08
RM27T0E _52 Drivetrain _053703 VF4BM TRANSFER / 4WD / AWD _0260838 TRANSFER SYSTEM J

VF4BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  4WD Control Switch Circuit  


WIRING DIAGRAM

C326395E12
0.677,1.948 1.135,2.146 0.458,0.198 10 false G18 0.667,2.094 2.24,2.323 1.573,0.229 10 false Transfer Position Switch 0.51,1.135 0.667,1.333 0.156,0.198 10 false 4 0.698,1.135 1.156,1.333 0.458,0.198 10 false GND 1.177,0.979 1.604,1.156 0.427,0.177 10 false H4F 1.729,1.104 2.042,1.302 0.313,0.198 10 false H4L 1.188,1.385 1.5,1.583 0.313,0.198 10 false L4L 2.542,0.813 3,1.01 0.458,0.198 10 false HI 2.563,1.438 2.875,1.635 0.313,0.198 10 false LO 2.854,0.813 3.01,1.01 0.156,0.198 10 false 5 2.833,1.438 2.99,1.635 0.156,0.198 10 false 2 3.771,0.813 4.083,1.01 0.313,0.198 10 false 14 4.01,0.813 4.469,1.01 0.458,0.198 10 false 2-4 3.771,1.417 4.083,1.615 0.313,0.198 10 false 13 4,1.427 4.313,1.625 0.313,0.198 10 false LO 3.635,2.01 4.094,2.208 0.458,0.198 10 false G53 3.646,2.188 5.292,2.396 1.646,0.208 10 false 4 Wheel Drive Control ECU 4.521,0.24 4.781,0.427 0.26,0.188 10 false IG 5.813,2.063 6.979,2.427 1.167,0.365 10 false Combination Meter Assembly 0.438,2.406 2.302,2.604 1.865,0.198 10 false : CAN Communication Line 0.083,0.042 3.573,0.427 3.49,0.385 12 false 3 Drive Mode (H4F, H4L, or L4L) (for 2TR-FE or 5L-E):

C346662E04
0.313,1.969 3.125,2.365 2.813,0.396 10 false Transfer Position Switch (Combination Switch Assembly)*1 0.688,0.927 1.24,1.167 0.552,0.24 10 false GND 1.51,0.76 1.802,0.927 0.292,0.167 10 false H4 1.542,1.104 1.854,1.313 0.313,0.208 10 false L4 0.521,0.917 0.719,1.115 0.198,0.198 10 false 4 2.51,1.24 2.771,1.427 0.26,0.188 10 false LO 2.833,1.177 3.083,1.375 0.25,0.198 10 false 2 0.323,1.75 0.75,1.948 0.427,0.198 10 false G305 3.552,3.99 4.073,4.208 0.521,0.219 10 false G53 0.656,4.042 2.5,4.281 1.844,0.24 10 false Transfer Position Switch*2 0.635,3.802 2.104,4.01 1.469,0.208 10 false G18 0.677,2.917 1.229,3.156 0.552,0.24 10 false GND 1.5,2.771 1.792,2.938 0.292,0.167 10 false H4 1.521,3.146 1.833,3.354 0.313,0.208 10 false L4 0.427,2.927 0.615,3.125 0.188,0.198 10 false 4 2.51,3.281 2.875,3.438 0.365,0.156 10 false LO 2.802,3.271 2.99,3.49 0.188,0.219 10 false 2 2.479,4.771 6.188,4.969 3.708,0.198 10 false *1: w/ Combination Switch 2.448,5.156 6.521,5.406 4.073,0.25 10 false *2: w/o Combination Switch 3.531,4.198 5.5,4.427 1.969,0.229 10 false 4 Wheel Drive Control ECU 5.615,4.125 7.146,4.51 1.531,0.385 10 false Combination Meter Assembly 0.521,5.302 2.323,5.521 1.802,0.219 10 false : CAN Communication Line 3.979,3.292 4.302,3.458 0.323,0.167 10 false LO 3.656,3.292 3.948,3.542 0.292,0.25 10 false 13 4.604,2.594 5.104,2.906 0.5,0.313 10 false IG 0.094,0.063 5,0.354 4.906,0.292 12 false 4 Drive Mode (H4F, H4L, L4F or L4L) (for 1GR-FE or 1GD-FTV):

PROCEDURE

1.CHECK 4WD DRIVE MODE
a.

Check the 4WD drive mode.

Result
Result Proceed to
4 Drive Mode (H4F, H4L, L4F or L4L) (for 1GR-FE or 1GD-FTV) A
3 Drive Mode (H4F, H4L, or L4L) (for 2TR-FE or 5L-E) B



A

2.CONFIRM PROBLEM SYMPTOM

B

12.CONFIRM PROBLEM SYMPTOM
2.CONFIRM PROBLEM SYMPTOM
a.

Confirm the problem symptoms.

Result
Result Proceed to
The 4LO indicator light remains off after operating the transfer position switch (combination switch assembly) to L4*1
The 4LO indicator light remains off after operating the transfer position switch to L4*2
A
The 4LO indicator light remains on after operating the transfer position switch (combination switch assembly) to H4*1
The 4LO indicator light remains on after operating the transfer position switch to H4*2
B

*1: w/ Combination Switch

*2: w/o Combination Switch




A

3.CHECK 4LO INDICATOR LIGHT

B

9.CHECK 4LO INDICATOR LIGHT
3.CHECK 4LO INDICATOR LIGHT
HINT:

Perform the following procedure with the vehicle stopped.


a.

Turn the ignition switch to ON.


b.

for Automatic Transmission:

Move the shift lever to N.

for Manual Transmission:

Depress the clutch pedal.


c.

w/ Combination Switch:

Turn the transfer position switch (combination switch assembly) to L4.

w/o Combination Switch:

Turn the transfer position switch to L4.


d.

Check the 4LO indicator light.

Result
Result Proceed to
The 4LO indicator light remains off A
The 4LO indicator light is blinking or illuminated B

Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)




A

4.CHECK CAN COMMUNICATION LINE

B

END

4.CHECK CAN COMMUNICATION LINE
a.

Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM

OK:

"Bus Check" indicates no malfunctions in CAN communication.

Result
Result Proceed to
DTC is not output A
DTC is output B




A

5.READ VALUE USING GTS (TRANSFER POSITION SWITCH)

B

5.READ VALUE USING GTS (TRANSFER POSITION SWITCH)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Turn the ignition switch to ON.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Data List.


f.

According to the display on the GTS, read the Data List.

Four Wheel Drive
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Transfer Position Control SW Transfer position switch status/
ON or OFF
ON: L4
OFF: H4
-

OK:

w/ Combination Switch:

Display changes according to transfer position switch (combination switch assembly) operation.

w/ Combination Switch

Display changes according to transfer position switch operation.




OK

6.CHECK COMBINATION METER ASSEMBLY (4LO INDICATOR LIGHT)

NG

7.INSPECT COMBINATION SWITCH ASSEMBLY OR TRANSFER POSITION SWITCH
6.CHECK COMBINATION METER ASSEMBLY (4LO INDICATOR LIGHT)
a.

Turn the ignition switch off.


b.

Perform an Active Test of the combination meter assembly using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


c.

Check the combination meter assembly.

OK:

The 4LO indicator light turns on or off in accordance with the GTS.




OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

7.INSPECT COMBINATION SWITCH ASSEMBLY OR TRANSFER POSITION SWITCH
a.

w/ Combination Switch:

i.

Remove the transfer position switch (combination switch assembly) (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH(w/ Combination Switch)>REMOVAL).


ii.

Inspect the transfer position switch (combination switch assembly (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH(w/ Combination Switch)>INSPECTION).

OK:

The transfer position switch (combination switch assembly) operates normally.




b.

w/o Combination Switch:


ii.

Inspect the transfer position switch (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH(w/o Combination Switch)>ON-VEHICLE INSPECTION).

OK:

The transfer position switch operates normally.




Result:
Result Proceed to
OK A
NG w/ Combination Switch B
w/o Combination Switch C



A

8.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - COMBINATION SWITCH ASSEMBLY OR TRANSFER POSITION SWITCH

B

C

8.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - COMBINATION SWITCH ASSEMBLY OR TRANSFER POSITION SWITCH
a.

Disconnect the G53 4 wheel drive control ECU connector.


b.

w/ Combination Switch:

Disconnect the G305 transfer position switch (combination switch assembly) connector.


c.

w/o Combination Switch:

Disconnect the G18 transfer position switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Combination Switch:
Tester Connection Condition Specified Condition
G53-13 (LO) - G305-2 (LO) Always Below 1 Ω
G53-13 (LO) or G305-2 (LO) - Body ground Always 10 kΩ or higher
G305-4 (GND) - Body ground Always Below 1 Ω

w/o Combination Switch:
Tester Connection Condition Specified Condition
G53-13 (LO) - G18-2 (LO) Always Below 1 Ω
G53-13 (LO) or G18-2 (LO)) - Body ground Always 10 kΩ or higher
G18-4 (GND) - Body ground Always Below 1 Ω




OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK 4LO INDICATOR LIGHT
HINT:

Perform the following procedure with the vehicle stopped.


a.

Turn the ignition switch to ON.


b.

for Automatic Transmission:

Move the shift lever to N.

for Manual Transmission:

Depress the clutch pedal.


c.

w/ Combination Switch:

Turn the transfer position switch (combination switch assembly) to L4.

w/o Combination Switch:

Turn the transfer position switch to L4.


d.

Check the 4LO indicator light.

Result
Result Proceed to
The 4LO indicator light remains illuminated A
The 4LO indicator light is blinking or illuminated B

Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)




A

10.CHECK CAN COMMUNICATION LINE

B

END

10.CHECK CAN COMMUNICATION LINE
a.

Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM

OK:

"Bus Check" indicates no malfunctions in CAN communication.


Result
Result Proceed to
DTC is not output A
DTC is output B



A

11.READ VALUE USING GTS (4LO INDICATOR LIGHT)

B

11.READ VALUE USING GTS (4LO INDICATOR LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Turn the ignition switch to ON.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Data List.


f.

According to the display on the GTS, read the Data List.

Four Wheel Drive
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
L4 Indicator Request 4LO indicator light request/
Blink3, Blink2*, Blink1, ON, OFF
·

Blink3: Indicator light rapidly blinks

·

Blink1: Indicator light blinks

·

ON: Indicator light illuminates

·

OFF: Indicator light turns off


·

Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)



*: Item not equipped, therefore not displayed


i.

w/ Combination Switch:

Operate the transfer position switch (combination switch assembly) several times between H4 and L4, and then check the GTS display condition of the 4LO indicator light.

w/o Combination Switch:

Operate the transfer position switch several times between H4 and L4, and then check the GTS display condition of the 4LO indicator light.

Result:
Result Proceed to
Data List continues to display ON even when transfer position switch (combination switch assembly) is operated*1
Data List continues to display ON even when transfer position switch is operated*2
A
Data List display changes according to transfer position switch (combination switch assembly) operation*1
Data List display changes according to transfer position switch operation*2
B


*1: w/ Combination Switch

*2: w/o Combination Switch





A

REPLACE 4 WHEEL DRIVE CONTROL ECU

B

12.CONFIRM PROBLEM SYMPTOM
a.

Confirm the problem symptoms.


Result:
Result Proceed to
The center differential lock indicator light and 4LO indicator light remain off A
The center differential lock indicator light remains illuminated, and the 4LO indicator light remains off B
The center differential lock indicator light) and 4LO indicator light remain illuminated C



A

13.CHECK CENTER DIFFERENTIAL LOCK INDICATOR LIGHT

B

17.CHECK CENTER DIFFERENTIAL LOCK INDICATOR LIGHT

C

18.CHECK 4LO INDICATOR LIGHT
13.CHECK CENTER DIFFERENTIAL LOCK INDICATOR LIGHT
a.

Turn the ignition switch to ON.


b.

for Automatic Transmission:

Move the shift lever to N.

for Manual Transmission:

Depress the clutch pedal.


c.

Turn the transfer position switch to H4L.


d.

Wait for 60 seconds.


e.

Check the center differential lock indicator light.


Result:
Result Proceed to
The center differential lock indicator light blinks*1 or illuminates A
The center differential lock indicator light rapidly blinks*2 or remains off B


·

*1 (Blinking): Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

*2 (Rapidly blinking): Blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off)



A

END

B

14.CHECK DTC
14.CHECK DTC
a.

Turn the transfer position switch to L4L.


b.

Check if DTC P279E is output after 60 seconds elapse (See page ).


Result:
Result Proceed to
DTC P279E is not output A
DTC P279E is output B



A

15.CHECK CAN COMMUNICATION LINE

B

15.CHECK CAN COMMUNICATION LINE
a.

Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.

w/ Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM

w/o Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM

OK:

"Bus Check" indicates no malfunctions in CAN communication.


Result
Result Proceed to
DTC is not output A
DTC is output w/ Central Gateway ECU B
w/o Central Gateway ECU C



A

16.CHECK TRANSFER POSITION SWITCH

B

C

16.CHECK TRANSFER POSITION SWITCH
a.
C388082C02
0.594,1.271 0.948,1.51 0.354,0.24 1.417,1.802 0.854,2.448 true 1.865,1.813 2.594,2.406 true 0.625,1.292 1.083,1.49 0.458,0.198 10 false G18 0.771,2.49 1.083,2.688 0.313,0.198 10 false HI 2.656,2.417 2.969,2.615 0.313,0.198 10 false LO
*a Component with harness connected
(Transfer Position Switch)


Remove the transfer position switch with its connector still connected.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G18-5 (HI) - Body ground Ignition switch ON
H4F position
Below 1.5 V
Ignition switch ON
H4L position
Below 1.5 V
Ignition switch ON
L4L position
10.5 to 14 V
G18-2 (LO) - Body ground Ignition switch ON
H4F position
10.5 to 14 V
Ignition switch ON
H4L position
Below 1.5 V
Ignition switch ON
L4L position
Below 1.5 V




OK

NG

17.CHECK CENTER DIFFERENTIAL LOCK INDICATOR LIGHT
a.

Turn the ignition switch to ON.


b.

for Automatic Transmission:

Move the shift lever to N.

for Manual Transmission:

Depress the clutch pedal.


c.

Turn the transfer position switch to H4F.


d.

Wait for 60 seconds.


e.

Check the center differential lock indicator light.


Result:
Result Proceed to
The center differential lock indicator light blinks*1 or turns off A
The center differential lock indicator light rapidly blinks*2 or remains on B


·

*1 (Blinking): Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

*2 (Rapidly blinking): Blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off)



A

END

B

18.CHECK 4LO INDICATOR LIGHT
HINT:

Perform the following procedures with the vehicle stopped.


a.

Turn the ignition switch to ON.


b.

for Automatic Transmission:

Move the shift lever to N.

for Manual Transmission:

Depress the clutch pedal.


c.

Turn the transfer position switch to H4L.


d.

Wait for 60 seconds.


e.

Check the 4LO indicator light.


Result:
Result Proceed to
The 4LO indicator light blinks*1 or turns off A
The 4LO indicator light rapidly blinks*2 or remains on B


·

*1 (Blinking): Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

*2 (Rapidly blinking): Blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off)



A

END

B

19.CHECK DTC
19.CHECK DTC
a.

Turn the transfer position switch to H4F.


b.

Check if DTC P279E is output after 60 seconds elapse.


Result:
Result Proceed to
DTC P279E is not output A
DTC P279E is output B



A

20.CHECK TRANSFER POSITION SWITCH

B

20.CHECK TRANSFER POSITION SWITCH
a.
C388082C03
0.594,1.271 0.948,1.51 0.354,0.24 1.417,1.802 0.854,2.448 true 1.854,1.823 2.594,2.417 true 0.625,1.292 1.083,1.49 0.458,0.198 10 false G18 0.771,2.49 1.083,2.688 0.313,0.198 10 false HI 2.656,2.417 2.969,2.615 0.313,0.198 10 false LO 0.375,0.375 0.688,0.573 0.313,0.198 10 false *a
*a Component with harness connected
(Transfer Position Switch)


Remove the transfer position switch with its connector still connected.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G18-5 (HI) - Body ground Ignition switch ON
H4F position
Below 1.5 V
Ignition switch ON
H4L position
Below 1.5 V
Ignition switch ON
L4L position
10.5 to 14 V
G18-2 (LO) - Body ground Ignition switch ON
H4F position
10.5 to 14 V
Ignition switch ON
H4L position
Below 1.5 V
Ignition switch ON
L4L position
Below 1.5 V



Result
Result Proceed to
OK w/ Central Gateway ECU A
w/o Central Gateway ECU B
NG C


A

B

C