After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting and reconnecting the battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
This section describes the standard values for all CAN related components.
The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
NO. 1 CAN JUNCTION CONNECTOR
Check the No. 1 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | ·
for No. 5 CAN Junction Connector (for LHD) ·
for No. 4 CAN Junction Connector (for RHD) |
| *c | ·
for ECM (for LHD) ·
for Combination Meter Assembly (for RHD) |
*d | for Brake Actuator Assembly (Skid Control ECU) |
Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
|
*1: for LHD *2: for RHD |
||
| A119-9 (CANH) | R*1, B*2 | ·
No. 5 CAN junction connector*1 ·
No. 4 CAN junction connector*2 |
| A119-20 (CANL) | W | |
| A119-10 (CANH) | LG | ·
ECM*1 ·
Combination meter assembly*2 |
| A119-21 (CANL) | W | |
| A119-11 (CANH) | B*1, R*2 | Brake actuator assembly (skid control ECU) |
| A119-22 (CANL) | W | |
NO. 2 CAN JUNCTION CONNECTOR (for LHD)
Check the No. 2 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | for No. 5 CAN Junction Connector |
| *c | for Airbag Sensor Assembly | *d | for No. 3 CAN Junction Connector |
Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| G293-1 (CANH) | GR | No. 5 CAN junction connector |
| G293-12 (CANL) | W | |
| G293-5 (CANH) | Y | Airbag sensor assembly |
| G293-16 (CANL) | W | |
| G293-6 (CANH) | LG | No. 3 CAN junction connector |
| G293-17 (CANL) | W |
NO. 3 CAN JUNCTION CONNECTOR (for LHD)
Check the No. 3 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | for No. 2 CAN Junction Connector |
| *c | for Combination Meter Assembly | *d | for Main Body ECU (Multiplex Network Body ECU) |
| *e | for DLC3 | - | - |
Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.
| Terminal No. | Wiring Color | Connected to |
|---|---|---|
| G294-1 (CANH) | LG | No. 2 CAN junction connector |
| G294-12 (CANL) | W | |
| G294-2 (CANH) | V | Combination meter assembly |
| G294-13 (CANL) | W | |
| G294-3 (CANH) | L | Main body ECU (multiplex network body ECU) |
| G294-14 (CANL) | W | |
| G294-5 (CANH) | R | DLC3 |
| G294-16 (CANL) | W |
NO. 4 CAN JUNCTION CONNECTOR (for RHD)
Check the No. 4 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | for No. 6 CAN Junction Connector |
| *c | for Main Body ECU (Multiplex Network Body ECU) | *d | for DLC3 |
| *e | for Airbag Sensor Assembly | *f | for No. 1 CAN Junction Connector |
Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| G295-1 (CANH) | GR | No. 6 CAN junction connector |
| G295-12 (CANL) | W | |
| G295-2 (CANH) | L | Main body ECU (multiplex network body ECU) |
| G295-13 (CANL) | W | |
| G295-4 (CANH) | R | DLC3 |
| G295-15 (CANL) | W | |
| G295-5 (CANH) | P | Airbag sensor assembly |
| G295-16 (CANL) | W | |
| G295-8 (CANH) | B | No. 1 CAN junction connector |
| G295-19 (CANL) | W |
NO. 5 CAN JUNCTION CONNECTOR (for LHD)
Check the No. 5 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | for No. 2 CAN Junction Connector |
| *c | for 4 Wheel Drive Control ECU | *d | for Air Conditioning Amplifier Assembly |
| *e | for No. 1 CAN Junction Connector | - | - |
Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| G296-1 (CANH) | GR | No. 2 CAN junction connector |
| G296-12 (CANL) | W | |
| G296-2 (CANH) | G | 4 wheel drive control ECU |
| G296-13 (CANL) | W | |
| G296-4 (CANH) | BR | Air conditioning amplifier assembly |
| G296-15 (CANL) | W | |
| G296-6 (CANH) | R | No. 1 CAN junction connector |
| G296-17 (CANL) | W |
NO. 6 CAN JUNCTION CONNECTOR (for RHD)
Check the No. 6 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | for No. 4 CAN Junction Connector |
| *c | for ECM | *d | for 4 Wheel Drive Control ECU |
| *e | for Air Conditioning Amplifier Assembly | - | - |
Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| G297-1 (CANH) | GR | No. 4 CAN junction connector |
| G297-12 (CANL) | W | |
| G297-2 (CANH) | LG | ECM |
| G297-13 (CANL) | W | |
| G297-3 (CANH) | G | 4 wheel drive control ECU |
| G297-14 (CANL) | W | |
| G297-4 (CANH) | BR | Air conditioning amplifier assembly |
| G297-15 (CANL) | W |
DLC3
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of DLC3 | - | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G317-6 (CANH) - G317-14 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G317-6 (CANH) - G317-4 (CG) | R - W-B | HIGH-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G317-14 (CANL) - G317-4 (CG) | W - W-B | LOW-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G317-6 (CANH) - G317-16 (BAT) | R - GR | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G317-14 (CANL) - G317-16 (BAT) | W - GR | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
ECM
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>5L-E (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM
Disconnect the cable from the negative (-) battery terminal.
Disconnect the ECM connector.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G183-25 (CANH) - G183-31 (CANL) | LG - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G183-25 (CANH) - G183-7 (EC) | LG - W-B | HIGH-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G183-31 (CANL) - G183-7 (EC) | W - W-B | LOW-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G183-25 (CANH) - G183-2 (BATT) | LG - L | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G183-31 (CANL) - G183-2 (BATT) | W - L | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)
Refer to Terminals of ECU.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TERMINALS OF ECU
| *a | Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU]) |
Disconnect the brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A6-25 (CANH) - A6-14 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A6-25 (CANH) - A6-1 (GND1) | B - W-B | HIGH-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A6-14 (CANL) - A6-1 (GND1) | W - W-B | LOW-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A6-25 (CANH) - A6-24 (BM) | B - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A6-14 (CANL) - A6-24 (BM) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G25-11 (CANH) - G25-12 (CANL) | BR - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G25-11 (CANH) - G25-14 (GND) | BR - W-B | HIGH-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G25-12 (CANL) - G25-14 (GND) | W - W-B | LOW-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G25-11 (CANH) - G25-21 (B) | BR - V | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G25-12 (CANL) - G25-21 (B) | W - V | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIRBAG SENSOR ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
| *a | Rear view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of DLC3 |
Disconnect the airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G1-13 (CANH) - G1-22 (CANL) | Y - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G1-13 (CANH) - G1-25 (E1) | Y - W-B | HIGH-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G1-22 (CANL) - G1-25 (E1) | W - W-B | LOW-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G1-13 (CANH) - G317-16 (BAT) | Y - GR | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G1-22 (CANL) - G317-16 (BAT) | W - GR | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G6-40 (CANH) - G6-39 (CANL) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G6-40 (CANH) - G6-21 (E2) | V - BR | HIGH-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G6-39 (CANL) - G6-21 (E2) | W - BR | LOW-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G6-40 (CANH) - G6-26 (B) | V - L | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G6-39 (CANL) - G6-26 (B) | W - L | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
4 WHEEL DRIVE CONTROL ECU
Refer to Terminals of ECU.
Click hereDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the 4 wheel drive control ECU connectors.
| *a | Front view of wire harness connector
(to 4 Wheel Drive Control ECU) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G53-20 (CANH) - G53-40 (CANL) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G53-20 (CANH) - G54-10 (GND) | G - W-B | HIGH-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G53-40 (CANL) - G54-10 (GND) | W - W-B | LOW-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G53-20 (CANH) - G53-21 (+B) | G - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G53-40 (CANL) - G53-21 (+B) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Refer to Terminals of ECU.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the main body ECU (multiplex network body ECU) connector.
| *a | Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G64-14 (CANH) - G64-13 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G64-14 (CANH) - G317-4 (CG) | L - W-B | HIGH-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G64-13 (CANL) - G317-4 (CG) | W - W-B | LOW-level CAN bus line - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G64-14 (CANH) - G317-16 (BAT) | L - GR | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G64-13 (CANL) - G317-16 (BAT) | W - GR | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |