Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P062712  Fuel Pump "A" Control Circuit Short to Battery  P062714  Fuel Pump "A" Control Circuit Short to Ground or Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P062712 Fuel Pump "A" Control Circuit Short to Battery Short in pre-stroke control valve circuit for 0.5 seconds.
(1 trip detection logic)
·

Short in pre-stroke control valve circuit

·

Fuel supply pump assembly

·

ECM


Comes on DTC stored SAE Code: P0629
P062714 Fuel Pump "A" Control Circuit Short to Ground or Open Open or short in pre-stroke control valve circuit for 0.5 seconds.
(1 trip detection logic)
·

Open or short in pre-stroke control valve circuit

·

Fuel supply pump assembly

·

ECM


Comes on DTC stored SAE Code: P0628

Related Data List
DTC No. Data List
P062712
P062714
·

Fuel Pressure (High)

·

Target Fuel Pressure (High)



HINT:
·

For more information on the fuel supply pump assembly (pre-stroke control valve) and common rail system, refer to System Description (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).

·

When DTC P062712 or P062714 is stored, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine / Data List / Fuel Pressure (High).

Under a stable operating condition such as idling, Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High).



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P062712
P062714
Idling for 1 second or more

WIRING DIAGRAM

A348538E89
0.719,1.854 1.177,2.052 0.458,0.198 10 false r6 0.708,2.052 2.802,2.281 2.094,0.229 10 false Pre-stroke Control Valve 5.677,0.646 6.313,0.844 0.635,0.198 10 false PCV+ 5.677,1.292 6.292,1.479 0.615,0.188 10 false PCV- 5.979,1.813 6.438,2.01 0.458,0.198 10 false C150 5.99,1.99 6.448,2.188 0.458,0.198 10 false ECM 2.073,0.75 2.531,0.948 0.458,0.198 10 false 1 2.073,1.406 2.531,1.604 0.458,0.198 10 false 2 5.479,0.75 5.938,0.948 0.458,0.198 10 false 3 5.49,1.438 5.948,1.635 0.458,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)
a.

Inspect the pre-stroke control valve.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)

NG

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)
a.

Disconnect the pre-stroke control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r6-1 - C150-3 (PCV+) Always Below 1 Ω
r6-2 - C150-4 (PCV-) Always Below 1 Ω
r6-1 or C150-3 (PCV+) - Body ground and other terminals Always 10 kΩ or higher
r6-2 or C150-4 (PCV-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Start the engine and idle it for 1 second or more.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
DTC P062712 or P062714 is output B




A

END

B

4.REPLACE ECM
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine and idle it for 1 second or more.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED