DPF (Diesel Particulate Filter) is an emission control system which processes the particulate matter (PM) that is emitted from a diesel engine. The DPF catalyst has a porous ceramic structure which has a PM collecting function. The PM that is collected is continuously treated by oxidation due to catalytic action at high temperatures, however PM accumulation increases at low catalyst temperatures because the oxidation process slows down. The ECM performs PM forced regeneration so that the amount of accumulated PM does not exceed the threshold.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P042000 | Catalyst System Efficiency Below Threshold (Bank 1) | During PM forced regeneration, DOC catalyst temperature does not increase sufficiently for 3 minutes.
(2 trip detection logic) |
·
Exhaust manifold converter sub-assembly ·
Exhaust fuel addition injector assembly Common Inspection Item: ·
Fuel injection system ·
Intake/Exhaust system ·
After treatment control system |
Comes on | DTC stored | SAE Code: P0420 |
| P244A00 | Particulate Filter Differential Pressure Too Low Bank 1 | When driving, the catalyst differential pressure is continuously below the threshold for 7 seconds or more.
(2 trip detection logic) |
·
Exhaust manifold converter sub-assembly ·
Exhaust fuel addition injector assembly Common Inspection Item: ·
Fuel injection system ·
Intake/Exhaust system ·
After treatment control system |
Comes on | DTC stored | SAE Code: P244A |
| P244B00 | Particulate Filter Differential Pressure Too High Bank 1 | While driving, Catalyst Differential Pressure becomes more than 0.27 for 3 seconds
(1 trip detection logic) |
·
Exhaust manifold converter sub-assembly ·
Differential pressure sensor Common Inspection Item: ·
Fuel injection system ·
Intake/Exhaust system ·
After treatment control system |
Comes on | DTC stored | SAE Code: P244B |
| P245800 | Particulate Filter Regeneration Duration Bank 1 | When PM forced regeneration is manually performed, PM forced regeneration does not finish even after 60 minutes or more elapse.
(1 trip detection logic) |
·
Exhaust manifold converter sub-assembly ·
Exhaust fuel addition injector assembly Common Inspection Item: ·
Fuel injection system ·
Intake/Exhaust system ·
After treatment control system |
Comes on | DTC stored | SAE Code: P2458 |
| P246300 | Particulate Filter Restriction - Soot Accumulation Bank 1 | While driving, PM accumulation amount exceeds the limit.
(1 trip detection logic) |
·
Exhaust Manifold Converter sub-assembly ·
Exhaust fuel addition injector assembly Common Inspection Item: ·
Fuel injection system ·
Intake/Exhaust system ·
After treatment control system |
Comes on | DTC stored | SAE Code: P2463 |
PM forced regeneration may be prohibited due to a fail-safe operation that is performed when another DTC is stored (including engine output limitation).
| DTC No. | Data List |
|---|---|
| P042000
P244A00 P244B00 P245800 P246300 |
·
Exhaust Fuel Addition F/B Bank 1 ·
Catalyst Differential Pressure Bank 1 ·
Particulate Filter Differential Pressure Bank 1 |
The ECM monitors the differential pressure between the upstream and downstream of the DPF catalyst and also monitors exhaust gas temperature to detect a malfunction in the exhaust manifold converter sub-assembly.
The ECM monitors exhaust gas temperature increase while the exhaust fuel addition injector assembly adds fuel during PM forced regeneration. Exhaust gas temperature increases up to approximately 300 to 500°C (572 to 932°F) during PM forced regeneration. If the temperature does not increase even after a certain amount of time has elapsed, the ECM determines that the DOC catalyst is abnormal and illuminates the MIL.
The ECM monitors the DPF catalyst differential pressure when driving and illuminates the MIL when the difference in pressure before and after the catalyst is below the threshold.
The ECM compares pressure upstream and downstream of the DPF catalyst to monitor the differential pressure. If the differential pressure is large, the ECM determines that the DPF catalyst is contaminated or has deteriorated and illuminates the MIL.
When PM forced regeneration is manually performed, PM forced generation does not finish even after 60 minutes or more elapse, the ECM determines that there is problem with the DPF catalyst and illuminates the MIL.
The ECM monitors the PM Accumulation Ratio Bank 1 and when the accumulated PM volume in the DPF catalyst exceeds the limit, the ECM illuminates the MIL.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P042000
P244A00 P245800 P246300 |
PM forced regeneration |
| P244B00 | Engine is running at 4000 rpm with no load for 10 seconds or more. |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION
After the engine switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting and reconnecting the battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
If DTC P245800 or P246300 is stored, fail-safe controls engine power output and PM forced regeneration is prohibited. In this case, PM forced regeneration can be performed after disconnecting the EFI-MAIN NO. 1 fuse or battery terminal and waiting for 60 seconds or more before connecting it again.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Record the stored DTC and freeze frame data.
Check Exhaust Fuel Addition F/B Bank 1 and Catalyst Differential Pressure Bank 1 in the freeze frame data.
When the Exhaust Fuel Addition F/B Bank 1 value is 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM regeneration control.
When the Catalyst Differential Pressure Bank 1 value is more than 0.27, it indicates a high possibility that DPF catalyst is clogged.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P244A00 is output | A |
| DTC P244B00 is output | B |
| DTC P244B00 is output at the same time as P246300 | |
| DTC P042000, P245800 or P246300 is output | C |
| Other relevant DTCs are output | D |
A
C
D
B
Be careful of being burned by exhaust gases during the following inspection.
Before checking the differential pressure sensor, perform a visual inspection of the differential pressure pipes and check that they are properly connected and no air is leaking from the pipes or hoses. If a malfunction is found, repair it before checking the sensor.
| *1 | Air Hose (Downstream) | *2 | Air Hose (Upstream) |
| *3 | No. 2 Vacuum Pipe | *4 | No. 1 Vacuum Pipe |
| *1 | Air Hose |
Disconnect the air hoses (both upstream and downstream) from the differential pressure sensor.
Start the engine.
Check if there are exhaust gas pulsations from both air hoses during idling.
Exhaust gas pulsation exists.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Particulate Filter Differential Pressure Bank 1.
Check that the differential pressure is as specified below.
Approximately 0 kPa
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Air Hose (Upstream) |
Connect the upstream air hose to the differential pressure sensor.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Particulate Filter Differential Pressure Bank 1.
Start the engine.
Engine is running at 4000 rpm with no load for 10 seconds or more.
Check that the differential pressure is as specified below.
| Particulate Filter Differential Pressure Bank 1 | Proceed to |
|---|---|
| 1.5 kPa or higher | A |
| Below 1.5 kPa | B |
B
A
Replace the differential pressure sensor.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the downstream air hose to the differential pressure sensor.
| *1 | Air Hose (Downstream) | - | - |
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Particulate Filter Differential Pressure Bank 1.
Start the engine.
Engine is running at 4000 rpm with no load for 10 seconds or more.
Check that the differential pressure is as specified below.
| Particulate Filter Differential Pressure Bank 1 | Proceed to |
|---|---|
| -1.5 to 1.5 kPa | A |
| Higher than 1.5 kPa | B |
A
B
It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.
If the differential pressure before and after the DPF is low, it is very likely that there is no DPF or the material inside the DPF is missing due to erosion, etc. If the DPF catalyst is eroded, do not replace the DPF at this time, as troubleshooting the cause and other repairs are necessary.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace No. 1 vacuum pipe or No. 2 vacuum pipe.
| Proceed to |
|---|
| NEXT |
NEXT
Diagnose relevant DTCs.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.
Stop the vehicle and allow the engine to idle.
Fully depress the accelerator pedal for 5 seconds, and then release it [A].
Repeat the procedure [A] 10 times [B].
Check for black smoke emission during the procedures [A] and [B].
Black smoke is emitted less than 5 times.
Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.
| Proceed to |
|---|
| OK |
| NG |
NG
OK
It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.
This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.
| Proceed to |
|---|
| NEXT |
NEXT
Remove the EFI-MAIN NO. 1 fuse or disconnect the cable from the battery terminal for 60 seconds or more, and then reinstall the EFI-MAIN NO. 1 fuse or reconnect the cable to the battery terminal.
The amount of built up particulate matter recorded by the ECM cannot be initialized by the GTS.
If the amount of built up particulate matter recorded by the ECM is not initialized, PM forced regeneration cannot be performed using the GTS.
Turn the engine switch on (IG).
Turn the engine switch off and wait for 30 seconds or more.
Turn the engine switch on (IG) and wait for 10 seconds or more.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Maintain the maximum possible engine speed under no load for 10 seconds to blow out all soot from inside the exhaust pipe.
If only a low engine speed is continuously maintained, soot may accumulate at the end of the catalyst.
When soot accumulates at the end of the catalyst, it may not be possible to perform PM forced regeneration control normally.
Enter the following menus: Powertrain / Engine / Utility / PM Regenerate Mode.
Enter PM Regenerate Mode.
Be careful of the exhaust pipes and surrounding areas, as they become extremely hot when performing PM forced regeneration.
Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S2 and DPNR/DPF Status Regeneration (PM).
Check for temperature increases and abnormal white smoke during PM forced regeneration.
PM forced regeneration takes 15 to 40 minutes to finish.
The time it takes to complete PM forced regeneration changes depending on "PM Accumulation Ratio Bank 1" and the vehicle operating conditions.
If the value of "Catalyst Differential Press Bank 1" increases too much during the PM forced regeneration, the fail-safe function activates and PM forced regeneration is stopped.
Perform PM forced regeneration control until the display on the multi-information display turns off.
If actions such as depressing the accelerator pedal or clutch pedal or operating the DPF switch, etc. are performed during PM forced regeneration, PM forced regeneration stops. If PM forced regeneration stops, it is necessary to perform it again.
PM forced regeneration control is not complete until the display on the multi-information display turns off.
| Result | Proceed to |
|---|---|
| During PM forced regeneration, temperature of Exhaust Temperature B1S2 is 300 to 500°C and no white smoke is generated | A |
| During PM forced regeneration, temperature of Exhaust Temperature B1S2 is 300 to 500°C and abnormal white smoke is generated*1 | B |
| Other than above*2 | C |
*1: If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DPF catalyst.
*1: When there is a malfunction with combustion control, operation performance may be reduced and abnormalities may be felt even if PM forced regeneration is performed.
*2: An excess of accumulated PM is the result of a malfunction in the control system causing poor combustion and an increase in black smoke.
A
B
C
It has been determined that the exhaust fuel addition injector assembly and No. 1 injector holder need to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust fuel addition injector assembly and No. 1 injector holder.
If there is no malfunction in the electrical system, Exhaust Temperature B1S2 is 500°C (932°F) or less even though fuel is injected, and white smoke is not emitted, replace the exhaust fuel addition injector assembly together with the No. 1 injector holder.
| Proceed to |
|---|
| NEXT |
NEXT
It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.
If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DPF catalyst. When there is a malfunction with combustion control, operation performance may be reduced and abnormalities may be felt even if PM forced regeneration is performed.
| Proceed to |
|---|
| NEXT |
NEXT
Check the fuel injection system.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>Fuel Injection System
| Proceed to |
|---|
| NEXT |
NEXT
Check the intake/exhaust system.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>Intake/Exhaust System
| Proceed to |
|---|
| NEXT |
NEXT
Check the after treatment control system.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>After Treatment Control System
| Proceed to |
|---|
| NEXT |
NEXT
Replace the following items only when it has been determined necessary based on diagnosis for DTC P042000, P244A00, P244B00, P245800 and P246300.
Replace the exhaust manifold converter sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/ DPF)>REMOVAL
Perform the initialization procedure for "Catalyst Deterioration Learning Value Clear" and "DPF Deposition Value Clear".
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION
Replace the exhaust fuel addition injector assembly and No. 1 injector holder.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>REMOVAL
If there is no malfunction in the electrical system, Exhaust Temperature B1S2 is 500°C (932°F) or less even though fuel is injected, and white smoke is not emitted, replace the exhaust fuel addition injector assembly together with the No. 1 injector holder.
Repair or replace the malfunctioning part confirmed in the diagnosis of the fuel injection system, intake/exhaust system and after treatment control system.
Check for DTCs output in step 1.
| Result | Proceed to |
|---|---|
| DTC P244A00 is output | A |
| DTC other than DTC P244A00 output | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Particulate Filter Differential Pressure Bank 1.
Start the engine.
Engine is running at 4000 rpm with no load for 10 seconds or more.
Confirmation that the differential pressure is higher than 1.5 kPa.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Perform PM forced regeneration.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
PM forced regeneration completes normally.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Particulate Filter Differential Pressure Bank 1.
Check the DPF Differential Pressure Bank 1 values from idle speed to unloaded maximum engine speed.
| Result | Proceed to |
|---|---|
| Particulate Filter Differential Pressure Bank 1 increases as engine speed increases from idle speed | A |
| Except above | B |
If Particulate Filter Differential Pressure Bank 1 indicates negative pressure for approx. 1 second as shown in the illustration (A) when the engine speed increases, the differential pressure sensor piping of the DPF catalyst may be clogged.
A
B
Be careful of being burned by exhaust gases during the following inspection.
Before checking the differential pressure sensor, perform a visual inspection of the differential pressure pipes and check that they are properly connected and no air is leaking from the pipes or hoses. If a malfunction is found, repair it before checking the sensor.
| *1 | Air Hose (Downstream) | *2 | Air Hose (Upstream) |
| *3 | No. 2 Vacuum Pipe | *4 | No. 1 Vacuum Pipe |
| *1 | Air Hose |
Disconnect the air hoses (both upstream and downstream) from the differential pressure sensor.
Start the engine.
Check if there are exhaust gas pulsations from both air hoses during idling.
Exhaust gas pulsation exists.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the differential pressure sensor.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.
Stop the vehicle and allow the engine to idle.
Fully depress the accelerator pedal for 5 seconds, and then release it [A].
Repeat the procedure [A] 10 times [B].
Check for black smoke emission during the procedures [A] and [B].
Black smoke is emitted less than 5 times.
Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Catalyst Differential Pressure Bank 1.
Check the value of Catalyst Differential Pressure Bank 1 at 4000 rpm without load.
| Result | Proceed to |
|---|---|
| Catalyst Differential Pressure Bank 1 is more than 0.27 | A |
| Except above | B |
A
B
Repair or replace No. 1 vacuum pipe or No. 2 vacuum pipe.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Particulate Filter Differential Pressure Bank 1.
Check the DPF Differential Pressure Bank 1 values from idle speed to unloaded maximum engine speed.
If Particulate Filter Differential Pressure Bank 1 indicates negative pressure for approx. 1 second as shown in the illustration (A) when the engine speed increases, the differential pressure sensor piping of the DPF catalyst may be clogged.
Particulate Filter Differential Pressure Bank 1 increases as engine speed increases from idle speed.
| Proceed to |
|---|
| OK |
| NG |
NG
OK
Remove the EFI-MAIN NO. 1 fuse or disconnect the cable from the battery terminal for 60 seconds or more, and then reinstall the EFI-MAIN NO. 1 fuse or reconnect the cable to the battery terminal.
The amount of built up particulate matter recorded by the ECM cannot be initialized by the GTS.
If the amount of built up particulate matter recorded by the ECM is not initialized, PM forced regeneration cannot be performed using the GTS.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs.
Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).
Perform PM forced regeneration.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
PM forced regeneration completes normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Even though it has been determined that the exhaust manifold converter sub-assembly needs to be replaced, make sure to perform all diagnostic procedures for DTC P244B00 before replacing it.
| Proceed to |
|---|
| NEXT |
NEXT