Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0442647 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P127112  Pressure Discharge Valve Circuit Short to Battery  P127114  Pressure Discharge Valve Circuit Short to Ground or Open  P127273  Pressure Discharge Valve Actuator Stuck Closed  


DESCRIPTION

The ECM controls the internal fuel pressure of the common rail assembly by opening and closing the pressure discharge valve. When sudden deceleration occurs, the internal fuel pressure will temporarily become higher than usual and combustion noise may result. Therefore the ECM will open the valve temporarily to discharge the excess pressure inside the common rail assembly. Also, the pressure discharge valve opens when the engine switch is turned off to allow prompt discharge of the common rail internal pressure and so that the engine stops smoothly.

HINT:
·

For more information on the pressure discharge valve and common rail system, refer to System Description (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).

·

If DTC P127112, P127114 and/or P127273 is present, refer to the DTC chart for the fuel system (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).



A208468E07
3.719,2.781 3.49,2.781 false 3.667,3 3.479,3.135 3.479,3.135 3.396,3.135 false 3.896,2.427 4.083,2.229 4.083,2.229 4.188,2.229 false 0.052,0.052 4.219,0.313 4.167,0.26 10 false Pressure Discharge Valve Operation Due to Sudden Deceleration: 0.927,0.375 2.031,0.833 1.104,0.458 10 false Accelerator Pedal Opening Angle 0.469,1.385 2.115,1.604 1.646,0.219 10 false Pressure Discharge Valve 1.135,2.292 2.042,2.542 0.906,0.25 10 false Fuel Pressure 2.594,0.542 2.979,0.771 0.385,0.229 10 false Open 4.135,1.396 4.521,1.656 0.385,0.26 10 false Open 2.594,1.156 3.104,1.396 0.51,0.24 10 false Closed 4.135,0.719 4.656,0.958 0.521,0.24 10 false Closed 4.25,2.146 6.219,2.406 1.969,0.26 10 false w/o Pressure Discharge Valve 1.719,2.688 3.542,2.948 1.823,0.26 10 false w/ Pressure Discharge Valve 2.104,3.042 3.635,3.271 1.531,0.229 10 false Target Fuel Pressure 3.927,3.292 5.042,3.521 1.115,0.229 10 false Time Reduction 3.323,3.531 3.698,3.771 0.375,0.24 10 false Time

A362191E01
4.219,2.01 4.792,1.573 4.792,1.573 4.906,1.573 true 3.042,2.406 3.146,2.406 3.146,2.406 3.729,1.667 true 0.104,0.115 3.49,0.313 3.385,0.198 10 false Cross Section Diagram of Pressure Discharge Valve: 1.594,0.583 3.854,0.813 2.26,0.229 10 false Return to Fuel Tank (Low Pressure) 0.313,1.521 2.156,1.917 1.844,0.396 10 false From Common Rail Assembly (High Pressure) 2.667,2.313 3.115,2.521 0.448,0.208 10 false Valve 4.958,1.51 5.583,1.729 0.625,0.219 10 false Solenoid

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P127112 Pressure Discharge Valve Circuit Short to Battery Short in pressure discharge valve circuit for 0.5 seconds.
(2 trip detection logic)
·

Short in pressure discharge valve circuit

·

Pressure discharge valve (common rail assembly)

·

ECM


Comes on DTC stored SAE Code: P1274
P127114 Pressure Discharge Valve Circuit Short to Ground or Open Open in pressure discharge valve circuit for 0.5 seconds.
(2 trip detection logic)
·

Open in pressure discharge valve circuit

·

Pressure discharge valve (common rail assembly)

·

ECM


Comes on DTC stored SAE Code: P1273
P127273 Pressure Discharge Valve Actuator Stuck Closed The fuel pressure does not decrease while the engine is running.
(1 trip detection logic)
·

Open or short in pressure discharge valve circuit (P127112 or P127114 is stored simultaneously)

·

Pressure discharge valve (common rail assembly)

·

ECM


Comes on DTC stored SAE Code: P1272

Related Data List
DTC No. Data List
P127112
P127114
P127273
·

Fuel Pressure (High)

·

Target Fuel Pressure (High)



HINT:
·

After confirming DTC P127112, P127114 and/or P127273, check the fuel pressure inside the common rail by entering the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).

·

DTC P127112:

After clearing the DTC, drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Check that P127112 is not output.

·

DTC P127114:

After clearing the DTC, drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Check that P127114 is not output.

·

DTC P127273:

After clearing the DTC, perform the following procedure 5 times, and then check that P127273 is not output: Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal.


Reference
Engine Speed Fuel Pressure (kPag)
Idling Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High)
3000 rpm (No engine load)

Results of Real-vehicle Check
Condition Fuel Pressure (High)
Idling
Fuel Pressure (High)
1 Second after Engine Stopped
Pressure discharge valve normal 35000 kPag 500 kPag
Open in pressure discharge valve circuit 35000 kPag 30000 kPag


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P127112
P127114
Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal.
P127273 Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Perform this 5 times.

MONITOR DESCRIPTION

DTC P127112, P127114 (Open or short in pressure discharge valve circuit):

This DTC is output when there is an open or short circuit in the pressure discharge valve circuit. When this DTC is output, the ECM enters fail-safe mode and restricts the engine output. The ECM stays in fail-safe mode until the engine switch is turned off.


DTC P127273 (Pressure discharge valve stuck closed):

The pressure discharge valve opens when the common rail target fuel pressure decreases during deceleration, decreasing the fuel pressure in the common rail assembly. The ECM compares the speed that the fuel pressure decreases with the speed that the common rail target fuel pressure decreases.

When the ECM determines that the decreasing rate of the fuel pressure is smaller than the common rail target fuel pressure, the ECM determines that the valve is stuck closed or there is a fuel supply pump assembly malfunction (overpressure) and outputs this DTC.

When this DTC is output, the ECM enters fail-safe mode and restricts the engine output. The ECM stays in fail-safe mode until the engine switch is turned off.


WIRING DIAGRAM

A348538E90
0.719,1.854 1.177,2.052 0.458,0.198 10 false r9 0.708,2.052 2.802,2.281 2.094,0.229 10 false Pressure Discharge Valve 5.677,0.646 6.313,0.844 0.635,0.198 10 false PRV+ 5.677,1.292 6.292,1.479 0.615,0.188 10 false PRV- 5.979,1.813 6.438,2.01 0.458,0.198 10 false C150 5.979,1.99 6.438,2.188 0.458,0.198 10 false ECM 2.073,0.521 2.531,0.719 0.458,0.198 10 false 1 2.083,1.188 2.542,1.385 0.458,0.198 10 false 2 5.469,0.531 5.927,0.729 0.458,0.198 10 false 2 5.469,1.188 5.927,1.385 0.458,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).


HINT:
·

After completing repairs, confirm that DTC P127112, P127114 and/or P127273 do not recur.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK IF DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 5 times.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the pending DTCs.

Result:
Result Proceed to
DTC P127273 is output A
DTC P127112 or P127114 is output B
DTC P127112 or P127114 and P127273 are output
Other DTCs are output C




A

2.CHECK COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE OPERATION)

B

8.INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE RESISTANCE)

C

2.CHECK COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine / Utility / Pressure Discharge Valve Check.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DATA LIST / ACTIVE TEST


e.

Select "Close to Open Check".


f.

Read the value of "Open and Engine OFF".

OK:

0.5 MPa or less


HINT:
·

When the system is normal, the value of "Open and Engine OFF" should be at or close to 0 MPa.

·

When the fuel pressure value of "Open and Engine OFF" does not become equal to or less than 0.5 MPa, the pressure discharge valve may be stuck closed.

·

When the fuel pressure values of "Close and Engine OFF" and "Open and Engine OFF" are both 0 MPa, the pressure discharge valve may be stuck open or there may be a fuel leak.

·

Perform "Always Closed Check" if the value is not 0 MPa when the pressure discharge valve is open during "Close to Open Check". If the results are the same as during "Close to Open Check", there is a pressure discharge valve operation malfunction.




Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT (DTC P127273)

NG

7.REPLACE COMMON RAIL ASSEMBLY
3.CHECK DTC OUTPUT (DTC P127273)
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG).


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by releasing the accelerator pedal. Perform this 5 times.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTC.


Result:
Result Proceed to
DTC P127273 is output A
No DTC is output B



A

4.REPLACE FUEL SUPPLY PUMP ASSEMBLY

B

END

4.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Perform this 5 times.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P127112, P127114 and/or P127273.


iii.

Check the DTC judgment result.

HINT:

If STATUS is INCOMPLETE, perform the following procedure 5 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.




Result:
Proceed to
NEXT



NEXT

END

7.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM
8.INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE RESISTANCE)
a.

Inspect the common rail assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>COMMON RAIL>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - ECM)

NG

7.REPLACE COMMON RAIL ASSEMBLY
9.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - ECM)
a.

Disconnect the pressure discharge valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r9-1 - C150-2 (PRV+) Always Below 1 Ω
r9-2 - C150-1 (PRV-) Always Below 1 Ω
r9-1 or C150-2 (PRV+) - Body ground and other terminals Always 10 kΩ or higher
r9-2 or C150-1 (PRV-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK IF DTC OUTPUT RECURS (DTC P127112, P127114 AND/OR P127273)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.CHECK IF DTC OUTPUT RECURS (DTC P127112, P127114 AND/OR P127273)
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 5 times.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the pending DTCs.

HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P127112, P127114 and/or P127273.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC DTC P127112, P127114 and/or P127273 is output B
All Readiness NORMAL A
ABNORMAL B


HINT:

If STATUS is INCOMPLETE, perform the following procedure 5 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.





A

END

B

11.REPLACE ECM
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED