Home › Engine / Hybrid System › 1GD-FTV (FUEL) › COMMON RAIL › from 2020.08
RM27T0E _51 Engine / Hybrid System _053670 1GD-FTV FUEL _0260592 COMMON RAIL A

1GD-FTV FUEL  COMMON RAIL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the common rail assembly removal/installation are shown below.

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Correction of steering angle neutral point Multi-terrain monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane departure alert system Drive the vehicle straight ahead at 40 km/h (25 mph) or more for 10 seconds or more. (Click here)
Pre-collision system
Lighting system (EXT) (for LED Headlight)
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Vehicle stability control system (for Hydraulic brake booster) Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds. (Click here)



NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe subassembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 25800 3.REMOVE EGR COOLER ASSEMBLY (w/ EGR System with EGR Cooler)

Hide 25800 4.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)

Hide 5.DRAIN ENGINE COOLANT (w/o EGR System)

Hide 55781E 6.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (w/o EGR System)

Hide 26100G 7.REMOVE DIESEL THROTTLE BODY ASSEMBLY (w/o EGR System)

Hide 87209 8.REMOVE WATER HOSE SUB-ASSEMBLY (w/o EGR System)

Hide 16278 9.REMOVE NO. 2 WATER BY-PASS PIPE (w/o EGR System)

Hide 12633 10.REMOVE NO. 3 ENGINE COVER BRACKET (w/o EGR System)

Hide 12632 11.REMOVE NO. 2 ENGINE COVER BRACKET (w/o EGR System)

Hide 44306 12.DISCONNECT VANE PUMP OIL RESERVOIR SUB-ASSEMBLY (w/o EGR System)

Hide 82121 13.DISCONNECT ENGINE WIRE (w/o EGR System)

Hide 25624 14.REMOVE EGR VALVE ADAPTER (w/o EGR System)

Hide 89463C 15.DISCONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Urea SCR System)

a.
A425655

Remove the 2 bolts, detach the connector, and then disconnect the No. 1 nitrogen oxides sensor from the cylinder head cover sub-assembly.


Hide 23804D 18.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)

Hide 23804C 20.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 21.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 22.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23282D 23.REMOVE NO. 4 FUEL HOSE

a.
A344943

Slide the clamp and disconnect the No. 4 fuel hose from the common rail assembly.


Hide 23810A 24.REMOVE COMMON RAIL ASSEMBLY

a.
A460313

Remove the 2 nuts and common rail assembly.

NOTICE:

Do not remove the pressure discharge valve.