77213B
1.INSTALL FUEL TANK TO FILLER PIPE HOSE
Align the fuel tank side mark with the hose side mark.
| *1 | Fuel Tank Side Mark |
| *2 | Hose Side Mark |
Install the fuel tank to filler pipe hose to the fuel tank.
77643A
2.INSTALL NO. 3 FUEL TANK PROTECTOR
Install the No. 3 fuel tank protector and attach the 4 clamps.
Install the 2 bolts.
77010
3.INSTALL FUEL TANK VENT TUBE ASSEMBLY
| *a | Co-rotation Prevention Check Mark |
Apply a co-rotation prevention check mark to the fuel tank vent tube assembly.
Perform this procedure when replacement of the fuel tank vent tube assembly is necessary.
Apply a light coat of diesel fuel or grease to a new gasket and install the gasket to the fuel tank sub-assembly.
| *a | Protrusion |
| *b | Groove |
Set the fuel tank vent tube assembly to the fuel tank sub-assembly.
Be careful not to bend the arm of the fuel sender gauge assembly.
Align the cutout of the fuel tank vent tube assembly to the groove of the fuel tank sub-assembly.
| *a | Rotational Start Point Mark (Fuel Tank Sub-assembly Side) |
| *b | Rotational Start Point Mark (Fuel Pump Gauge Retainer Side) |
Temporarily place the fuel pump gauge retainer by aligning the rotational start point mark of a new fuel pump gauge retainer with the rotational start point mark of the fuel tank sub-assembly while pressing the fuel tank vent tube assembly into the fuel tank sub-assembly.
| *1 | Fuel Pump Gauge Retainer |
| *a | SST (Claw Set) |
| *b | Rib |
| *c | Cutout |
| *d | SST (Claw Set) Incorrect Installation Point (Rotational Start Point Mark of Fuel Pump Gauge Retainer) |
Set 4 SSTs (claw sets) to the fuel pump gauge retainer and temporarily install.
Align the cutout of SST (claw set) to the rib of the fuel pump gauge retainer.
Do not place SST on the rotational start point mark of the fuel pump gauge retainer, otherwise SST (claw set) cannot be set correctly.
| *1 | Fuel Pump Gauge Retainer |
| *a | SST (Claw Set) |
| *b | Hook |
|
Press |
|
SST (Bolt) |
While firmly pressing the claw of SST (claw set) into rib of the fuel pump gauge retainer, tighten the bolt.
| *a | SST (Plate) |
| *b | SST (Claw Set) |
|
SST (Bolt) |
Temporarily install SST (plate) to SST (claw set) with 4 SSTs (bolts).
| *a | Center of Fuel Pump Gauge Retainer |
| *b | SST (Plate) |
Adjust the position of SST (plate) so that the setting hole of SST (handle) aligns with the center of the fuel pump gauge retainer.
| *1 | Fuel Pump Gauge Retainer |
| *a | SST (Plate) |
| *b | SST (Claw Set) |
| *c | SST (Bolt) |
| *d | Rib |
|
Press |
While firmly pressing the SST (claw set) into rib of the fuel pump gauge retainer, tighten SST (bolt).
| *a | Co-rotation Prevention Check Mark |
| *b | Tightening Start Position |
| *c | One and Half Rotation Position |
While one person presses the fuel tank vent tube assembly into the fuel tank sub-assembly, have another person firmly press the fuel pump gauge retainer into the threads of the fuel tank sub-assembly and tighten approximately one and a half turns.
Do not use any tools other than SST, such as a screwdriver, etc.
Do not use excessive force when pressing down on SST, as the fuel tank vent tube assembly will place excessive force on the pump gauge retainer and be difficult to remove, and parts may be damaged.
Do not use an impact wrench or turn the SST handle with excessive force, as parts may be damaged.
Do not rotate the fuel pump gauge retainer when the co-rotation prevention check mark is out of place.
| *a | SST (Plate) |
| *b | Person in Charge of Tightening |
| *c | Person in Charge of Supporting |
| *d | Approximately 180° |
While one person presses the fuel tank vent tube assembly into the fuel tank sub-assembly, have another person slowly tighten approximately 180°.
Check the tightening condition of the fuel pump gauge retainer.
| *1 | Fuel Pump Gauge Retainer |
| *2 | Fuel Tank Sub-assembly |
| *a | Vernier Caliper |
| *b | Measurement Position |
| *c | Measurement Height |
Using a vernier caliper, measure the upper surface dimensions of the fuel tank assembly at the 3 positions as shown in the illustration.
Measurement difference is within 3 mm.
If the measurement difference is approximately 6 mm, the threads misaligned by 1 threads (6 mm) and the fuel pump gauge retainer must be installed again.
| *a | SST (Handle) |
| *b | SST (Plate) |
| *c | Tightening Complete Position |
| *d | Rotational Start Point Mark of Fuel Pump Gauge Retainer |
| *e | Rotational Start Point Mark of Fuel Tank Assembly |
| *f | Person in Charge of Tightening |
| *g | Person in Charge of Supporting |
|
Tighten |
Install SST (handle) to SST (plate).
While one person presses the fuel tank vent tube assembly onto the fuel tank sub-assembly, have another person use SST (handle) and slowly tighten the fuel pump gauge retainer until it reaches the tightening complete position.
77209D
4.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL RETURN TUBE SUB-ASSEMBLY (for Single Tank Type)
Install the fuel tank main tube and fuel return tube with the 2 fuel tube joint clips.
Check that there are no scratches or foreign objects on the connecting parts.
Check that the fuel tube joints are inserted securely.
Check that the fuel tube joint clips are on the collars of the fuel tube joints.
After installing the fuel tube joint clips, check that the fuel tube joints cannot be pulled off.
| *1 | Fuel Tube Joint |
| *2 | O-Ring |
| *3 | Fuel Tube |
| *4 | Fuel Tube Joint Clip |
| *a | CORRECT |
| *b | INCORRECT |
Install the fuel tank main tube and fuel return tube to the fuel tank.
77209D
5.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL RETURN TUBE SUB-ASSEMBLY (for Double Tank Type)
Install the fuel tank main tube and fuel return tube with the 2 fuel tube joint clips.
Check that there are no scratches or foreign objects on the connecting parts.
Check that the fuel tube joints are inserted securely.
Check that the fuel tube joint clips are on the collars of the fuel tube joints.
After installing the fuel tube joint clips, check that the fuel tube joints cannot be pulled off.
| *1 | Fuel Tube Joint |
| *2 | O-Ring |
| *3 | Fuel Tube |
| *4 | Fuel Tube Joint Clip |
| *a | CORRECT |
| *b | INCORRECT |
Install the fuel tank main tube to the fuel tank.
Install the fuel return tube to the fuel tank and attach the clamp.
77651A
6.INSTALL FUEL TANK CUSHION
Install 3 new fuel tank cushions to the fuel tank.
77100U
7.INSTALL FUEL TANK SUB-ASSEMBLY
Set the fuel tank on a transmission jack and rise the transmission jack.
Do not allow the fuel tank to contact the vehicle, especially the differential.
Install the 2 fuel tank bands with the 2 pins and 2 clips.
Connect the 2 fuel tank bands with the 2 bolts.
77213B
8.CONNECT FUEL TANK TO FILLER PIPE HOSE
Connect the fuel tank to filler pipe hose to the filler pipe.
77012
9.CONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Single Tank Type)
Connect the fuel tank breather tube (See page Engine / Hybrid System>5L-E (FUEL)>FUEL SYSTEM>PRECAUTION).
10.CONNECT FUEL CUT OFF TUBE (for Single Tank Type)
77012
11.CONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Double Tank Type)
Connect the fuel tank breather tube (See page Engine / Hybrid System>5L-E (FUEL)>FUEL SYSTEM>PRECAUTION).
77207A
12.CONNECT FUEL RETURN TUBE SUB-ASSEMBLY (for Double Tank Type)
Connect the fuel return tube (See page Engine / Hybrid System>5L-E (FUEL)>FUEL SYSTEM>PRECAUTION).
13.CONNECT FUEL CUT OFF TUBE (for Double Tank Type)
Connect the fuel cut off tube (See page Engine / Hybrid System>5L-E (FUEL)>FUEL SYSTEM>PRECAUTION).
77207A
14.CONNECT FUEL RETURN TUBE SUB-ASSEMBLY (for Single Tank Type)
77209D
15.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)
77209D
16.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)
77606
17.INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
Install the No. 1 fuel tank protector with the 6 bolts.
58325E
18.INSTALL REAR FLOOR SERVICE HOLE COVER
Connect the fuel sender gauge connector.
Install the rear floor service hole cover with the 3 screws.
67918D
19.INSTALL REAR DOOR SCUFF PLATE LH
67934
20.INSTALL QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)
58371F
21.INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)
22.INSTALL REAR SEAT ASSEMBLY LH
for 60/40 Split Double-folding Seat Type LH Side:
Install the rear seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Double-folding Seat Type LH Side)>INSTALLATION).
for 60/40 Split Slide Walk-in Seat Type LH Side:
Install the rear seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type LH Side)>INSTALLATION).
23.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
24. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
25.BLEED AIR FROM FUEL SYSTEM
26.INSPECT FOR FUEL LEAK