Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › UREA TANK › from 2021.06
RM27T0E _51 Engine / Hybrid System _053675 1GD-FTV EMISSION CONTROL _0260632 UREA TANK A

1GD-FTV EMISSION CONTROL  UREA TANK  REMOVAL  


PROCEDURE

Hide 33030 2.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)

Hide 35000 3.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 53737A 4.REMOVE NO. 1 FRONT FENDER APRON TO FRAME SEAL LH

a.

Remove the 5 clips and No. 1 front fender apron to frame seal LH from the body.


Hide 82169 5.DISCONNECT NO. 3 FRAME WIRE

a.
A492923

Detach the 2 clamps and disconnect the No. 3 frame wire.


Hide 77840 6.DISCONNECT UREA TUBE WITH HEATER ASSEMBLY

a.

Disconnect the urea tube with heater assembly from the urea injector set (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA INJECTOR>REMOVAL).


b.
A409310

Detach the 4 clamps and disconnect the urea tube with heater assembly from the frame crossmember and urea tank sub-assembly.


Hide 77900 7.DISCONNECT UREA TANK FILLER PIPE WITH SUPPORT ASSEMBLY

NOTICE:

Check for dirt or mud on the urea tank breather tube sub-assembly, urea tank sub-assembly and around the urea tank filler pipe with support connector before disconnection. Clean if necessary.


a.

Disconnect the urea tank filler pipe with support assembly from the urea tank breather tube sub-assembly.

i.
A409311C01
2.104,1.417 1.594,1.74 1.594,1.74 1.438,1.74 true 1.229,1.646 1.438,1.854 0.208,0.208 10 true *a
*a Retainer
V100135

Pull
V100136

Pull Out


Detach the claw of the retainer of the urea tank filler pipe with support connector, pull up the retainer and disconnect the urea tank filler pipe with support connector from the urea tank breather tube sub-assembly.

NOTICE:
·

If there is any solidified urea solution (white solids) on the connection area, clean the solids off with a damp cloth, etc., before disconnecting the connector.

·

Be sure to disconnect the urea tank filler pipe with support connector by hand.

·

Check for foreign matter in the urea tank breather tube sub-assembly and around the urea tank filler pipe with support connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the urea tank breather tube sub-assembly and urea tank filler pipe with support connector.

·

Put the urea tank breather tube sub-assembly and urea tank filler pipe with support connector ends in plastic bags to prevent damage and foreign matter contamination.





b.

Disconnect the urea tank filler pipe with support assembly from the urea tank sub-assembly.

i.
A409312C01
1.479,0.49 1.917,0.281 1.917,0.281 2.125,0.281 true 2.146,0.188 2.458,0.385 0.313,0.198 10 true *a
*a Retainer
V100135

Pull
V100136

Pull Out


Detach the claw of the retainer of the urea tank filler pipe with support connector, pull up the retainer and disconnect the urea tank filler pipe with support connector from the urea tank sub-assembly.

NOTICE:
·

If there is any solidified urea solution (white solids) on the connection area, clean the solids off with a damp cloth, etc., before disconnecting the connector.

·

Be sure to disconnect the urea tank filler pipe with support connector by hand.

·

Check for foreign matter in the urea tank sub-assembly and around the urea tank filler pipe with support connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the urea tank sub-assembly and urea tank filler pipe with support connector.

·

Put the urea tank sub-assembly and urea tank filler pipe with support connector ends in plastic bags to prevent damage and foreign matter contamination.





Hide 77801 8.REMOVE UREA TANK SUB-ASSEMBLY

a.
A409313

Remove the 2 bolts and urea tank sub-assembly from the flame LH.


Hide 77903 9.REMOVE UREA TANK BREATHER TUBE SUB-ASSEMBLY

NOTICE:

Check for dirt or mud on the urea tank sub-assembly and around the urea tank breather tube connector before disconnection. Clean if necessary.


a.

Detach the clamp and remove the urea tank breather tube sub-assembly from the urea tank sub-assembly.

i.
A409314C01
1.75,0.354 1.865,0.354 1.865,0.354 2.156,0.719 true 1.573,0.25 1.771,0.458 0.198,0.208 10 false *a
*a Retainer
V100135

Pull
V100136

Pull Out


Detach the claw of the retainer of the urea tank breather tube connector, pull up the retainer and disconnect the urea tank breather tube connector from the urea tank sub-assembly.

NOTICE:
·

If there is any solidified urea solution (white solids) on the connection area, clean the solids off with a damp cloth, etc., before disconnecting the connector.

·

Be sure to disconnect the urea tank breather tube connector by hand.

·

Check for foreign matter in the urea tank sub-assembly and around the urea tank breather tube connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the urea tank sub-assembly and urea tank breather tube connector.

·

Put the urea tank sub-assembly and urea tank breather tube connector ends in plastic bags to prevent damage and foreign matter contamination.





Hide 77861 10.REMOVE NO. 1 UREA TANK BRACKET

a.
A409315

Remove the bolt and No. 1 urea tank bracket from the urea tank sub-assembly.


Hide 77862 11.REMOVE NO. 2 UREA TANK BRACKET

a.
A355509

Remove the bolt and No. 2 urea tank bracket from the urea tank sub-assembly.