Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2021.06
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  DCM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
DCM Communication Stop Mode Any of the following conditions are met:
·

"DCM" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "DCM Communication Stop Mode" in "DTC Combination Table".

Click here(Click here)


·

Telephone transceiver assembly branch wire or connector

·

Power source circuit of telephone transceiver assembly

·

Telephone transceiver assembly ground circuit

·

Telephone transceiver assembly



WIRING DIAGRAM

C459905E03
5.656,1.135 6.271,1.333 0.615,0.198 10 false CANP 5.656,1.667 6.271,1.865 0.615,0.198 10 false CANN 5.646,2.385 6.26,2.583 0.615,0.198 10 false +B 5.646,3.458 6.26,3.656 0.615,0.198 10 false IG2 5.646,4.302 6.26,4.5 0.615,0.198 10 false E 4.188,2.365 4.802,2.563 0.615,0.198 10 false DCM 1.531,1.031 2.146,1.229 0.615,0.198 10 false 4 1.521,1.552 2.135,1.75 0.615,0.198 10 false 15 5.375,1.042 5.99,1.24 0.615,0.198 10 false 25 5.365,1.552 5.979,1.75 0.615,0.198 10 false 26 5.448,2.396 6.063,2.594 0.615,0.198 10 false 1 5.375,3.333 5.99,3.531 0.615,0.198 10 false 19 5.375,4.198 5.99,4.396 0.615,0.198 10 false 20 5.333,4.958 5.948,5.156 0.615,0.198 10 false G333 5.344,5.135 6.75,5.531 1.406,0.396 10 false Telephone Transceiver Assembly 0.125,1.969 0.74,2.167 0.615,0.198 10 false G289 0.125,2.146 2.188,2.708 2.063,0.563 10 false No. 5 CAN Junction Connector 4.229,3.292 4.833,3.708 0.604,0.417 10 false IGN 2.271,2.51 3.208,2.833 0.938,0.323 10 false from Battery 2.104,3.448 3.177,3.896 1.073,0.448 10 false from IG2 Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (TELEPHONE TRANSCEIVER ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C404434C82
1.5,0.917 2,1.167 0.5,0.25 0.917,2.594 1.063,2.594 1.063,2.594 1.271,1.885 true 1.833,2.573 1.677,2.573 1.677,2.573 1.396,1.875 true 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 1.583,0.948 2.042,1.146 0.458,0.198 10 false G333 0.5,2.521 1.115,2.719 0.615,0.198 10 false CANP 1.927,2.49 2.542,2.688 0.615,0.198 10 false CANN
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)


Disconnect the telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G333-25 (CANP) - G333-26 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C404434C83
1.5,0.917 2,1.167 0.5,0.25 0.521,1.698 0.698,1.094 0.698,1.094 0.854,1.094 true 1.094,2.583 0.938,2.583 0.938,2.583 0.604,1.875 true 1.385,2.385 1.219,2.385 1.219,2.385 0.729,1.875 true 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 1.594,0.958 2.052,1.156 0.458,0.198 10 false G333 1.469,2.333 1.708,2.521 0.24,0.188 10 false E 0.958,1.021 1.219,1.198 0.26,0.177 10 false +B 1.156,2.5 1.417,2.677 0.26,0.177 10 false IG2
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G333-20 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G333-1 (+B) - Body ground Always 11 to 14 V
G333-19 (IG2) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)