Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › from 2021.06
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  U010E87  Lost Communication with Reductant Control Module Missing Message  U029D87  Lost Communication with NOx Sensor "A" Missing Message  U029E87  Lost Communication with NOx Sensor "B" Missing Message  U02A387  Lost Communication with PM Sensor Missing Message  


DESCRIPTION

The ECM and urea pump assembly (urea pump control ECU integrated urea pump) sends and receives data to and from the No. 1 nitrogen oxide sensor, No. 2 nitrogen oxide sensor and particulate matter sensor* via local CAN communication.

If a communication error occurs between the ECM and other parts such as the urea pump assembly (urea pump control ECU integrated urea pump) and No. 1 nitrogen oxide sensor or No. 2 nitrogen oxide sensor, the ECM stores this DTC.

HINT:

*: w/ Particulate matter sensor


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
U010E87 Lost Communication with Reductant Control Module Missing Message There is no communication between the ECM and urea pump assembly (urea pump control ECU integrated urea pump).
(1 trip detection logic)
·

ECM

·

Urea pump control ECU

·

CAN Communication System


Comes on DTC stored SAE Code: U010E
U029D87 Lost Communication with NOx Sensor "A" Missing Message Communication stops between the ECM and the No. 1 nitrogen oxides sensor for 1 second or more.
(1 trip detection logic)
·

No. 1 nitrogen oxides sensor

·

Harness or connector

·

ECM


Comes on DTC stored SAE Code: U029D
U029E87 Lost Communication with NOx Sensor "B" Missing Message Communication stops between the ECM and the No. 1 nitrogen oxides sensor for 1 second or more.
(1 trip detection logic)
·

No. 2 nitrogen oxides sensor

·

Harness or connector

·

ECM


Comes on DTC stored SAE Code: U029E
U02A387 Lost Communication with PM Sensor Missing Message Communication stops between the ECM and the particulate matter sensor for 1.6 seconds or more.
(1 trip detection logic)
·

Particulate matter sensor

·

Harness or connector

·

ECM


Comes on DTC stored SAE Code: U02A3

MONITOR DESCRIPTION

The ECM stores a DTC when a communication malfunction occurs between the ECM and the urea pump assembly (urea pump control ECU integrated urea pump) and the No. 1 NOx sensor or the No. 2 NOx sensor.

HINT:

*: w/ Particulate matter sensor


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
U010E87 Engine switch on (IG) and wait for 5 seconds or more.

WIRING DIAGRAM

A492024E02
3.469,5.021 5.302,5.219 1.833,0.198 10 false No. 1 Nitrogen Oxides Sensor 3.5,6.385 5.854,6.604 2.354,0.219 10 false No. 2 Nitrogen Oxides Sensor 4.604,4.24 5.219,4.438 0.615,0.198 10 false CAN+ 4.635,4.583 5.25,4.781 0.615,0.198 10 false CAN- 4.604,5.615 5.219,5.813 0.615,0.198 10 false CAN+ 4.635,5.948 5.25,6.146 0.615,0.198 10 false CAN- 3.969,4.25 4.583,4.448 0.615,0.198 10 false BATT 3.948,4.583 4.563,4.781 0.615,0.198 10 false GND 3.958,5.615 4.573,5.813 0.615,0.198 10 false BATT 3.938,5.958 4.552,6.156 0.615,0.198 10 false GND 3.177,4.396 4.094,4.594 0.917,0.198 10 false NOx FR 2.646,5.281 3.563,5.479 0.917,0.198 10 false NOx RR PM 2.021,8.229 3.969,8.448 1.948,0.219 10 false : CAN Communication Line 1.844,4.531 3.99,4.729 2.146,0.198 10 false NOx PM 0.344,6.479 1.26,6.677 0.917,0.198 10 false 250A FL 1.198,4.375 2.115,4.573 0.917,0.198 10 false NOx PM 0.583,7.99 1.5,8.188 0.917,0.198 10 false Battery 4.542,8.115 7.156,8.583 2.615,0.469 10 false Urea Pump Assembly (Urea Pump Control ECU Integrated Urea Pump) 3.719,3.156 4.167,3.385 0.448,0.229 10 false ECM 3.677,2.635 4.594,2.833 0.917,0.198 10 false MREL 6.073,2.26 6.688,2.458 0.615,0.198 10 false CAN+ 6.083,2.635 6.698,2.833 0.615,0.198 10 false CAN- 4.344,2.271 4.958,2.469 0.615,0.198 10 false CANU 4.344,2.625 4.958,2.823 0.615,0.198 10 false CAND 2,1.042 2.458,1.24 0.458,0.198 10 false DCU 0.875,0.635 1.333,0.833 0.458,0.198 10 false DCU 4.875,1.135 6.25,1.333 1.375,0.198 10 false DCU NO. 2 4.885,0.615 6.26,0.813 1.375,0.198 10 false DCU NO. 1 6.073,0.979 6.688,1.177 0.615,0.198 10 false +BU1 6.073,0.49 6.688,0.688 0.615,0.198 10 false +BU2 3.375,3.583 5.521,3.781 2.146,0.198 10 false EFI MAIN NO. 3 1.698,6.479 2.615,6.677 0.917,0.198 10 false 70A FL 1.708,2.896 3.854,3.094 2.146,0.198 10 false EFI MAIN NO. 1 1.135,2.365 1.76,2.885 0.625,0.521 10 false EFI MAIN NO. 1 5.833,7.958 6.146,8.156 0.313,0.198 10 false v6 2.75,2.24 3.063,2.438 0.313,0.198 10 false 1V 2.75,2.625 3.063,2.823 0.313,0.198 10 false 1V 2.74,3.865 3.052,4.063 0.313,0.198 10 false 1W 2.74,4.24 3.052,4.438 0.313,0.198 10 false 1W 2.417,4.865 2.729,5.063 0.313,0.198 10 false 1W 0.99,4.865 1.302,5.063 0.313,0.198 10 false 1S 2.771,4.042 3.083,4.24 0.313,0.198 10 false 10 2.604,4.656 2.917,4.854 0.313,0.198 10 false 11 2.813,3.656 3.125,3.854 0.313,0.198 10 false 8 2.823,2.417 3.135,2.615 0.313,0.198 10 false 7 2.823,2.021 3.135,2.219 0.313,0.198 10 false 6 3.698,3 4.281,3.188 0.583,0.188 10 false G184 3.479,4.854 4.354,5.01 0.875,0.156 10 false C181 3.5,6.208 4.115,6.406 0.615,0.198 10 false s6 5.115,4.104 5.417,4.354 0.302,0.25 10 false 2 5.104,4.438 5.26,4.635 0.156,0.198 10 false 3 3.75,4.427 3.906,4.625 0.156,0.198 10 false 4 3.76,4.146 3.917,4.344 0.156,0.198 10 false 5 3.74,5.51 3.896,5.708 0.156,0.198 10 false 5 3.729,5.833 3.885,6.031 0.156,0.198 10 false 4 5.073,5.802 5.229,6 0.156,0.198 10 false 3 5.073,5.427 5.229,5.625 0.156,0.198 10 false 2 4.833,2.479 5.135,2.729 0.302,0.25 10 false 35 4.833,2.115 5.135,2.365 0.302,0.25 10 false 27 5.781,0.823 5.938,1.021 0.156,0.198 10 false 4 5.792,0.313 5.948,0.51 0.156,0.198 10 false 8 5.781,2.063 5.938,2.26 0.156,0.198 10 false 3 5.771,2.448 6.073,2.698 0.302,0.25 10 false 2 1.135,4.656 1.448,4.854 0.313,0.198 10 false 1 1.156,0.354 1.458,0.604 0.302,0.25 10 false 2 0.792,0.344 1.104,0.542 0.313,0.198 10 false 1 2.49,0.375 2.646,0.573 0.156,0.198 10 false 5 4.979,0.354 5.292,0.552 0.313,0.198 10 false 1 5.375,0.365 5.677,0.615 0.302,0.25 10 false 2 4.979,0.865 5.292,1.063 0.313,0.198 10 false 1 5.385,0.865 5.688,1.115 0.302,0.25 10 false 2 1.771,0.688 2.083,0.885 0.313,0.198 10 false 1 2.49,0.688 2.792,0.938 0.302,0.25 10 false 2 1.771,0.375 1.927,0.573 0.156,0.198 10 false 3 3.438,2.531 3.74,2.781 0.302,0.25 10 false 14 3.604,4.104 3.906,4.354 0.302,0.25 10 false 2 3.281,4.083 3.594,4.281 0.313,0.198 10 false 1 2.375,5.469 2.677,5.719 0.302,0.25 10 false 2 2.365,5.083 2.677,5.281 0.313,0.198 10 false 1 3.125,3.385 3.438,3.583 0.313,0.198 10 false 1 3.125,3.75 3.427,4 0.302,0.25 10 false 2 5.854,7.156 6.156,7.406 0.302,0.25 10 false 1 5.865,7.531 6.167,7.781 0.302,0.25 10 false 5 6.083,7.281 6.698,7.479 0.615,0.198 10 false E01 6.083,7.656 6.698,7.854 0.615,0.198 10 false E02 3.458,7.615 5.313,7.896 1.854,0.281 10 false Particulate Matter Sensor* 3.458,7.458 3.771,7.656 0.313,0.198 10 false s8 3.979,6.896 4.594,7.094 0.615,0.198 10 false BATT 3.958,7.25 4.573,7.448 0.615,0.198 10 false GND 4.594,7.25 5.208,7.448 0.615,0.198 10 false CAN- 4.594,6.906 5.208,7.104 0.615,0.198 10 false CAN+ 3.771,6.781 4.083,6.979 0.313,0.198 10 false 1 3.781,7.104 3.938,7.302 0.156,0.198 10 false 4 5.083,6.74 5.24,6.938 0.156,0.198 10 false 2 5.073,7.094 5.229,7.292 0.156,0.198 10 false 3 0.708,3.865 1.021,4.063 0.313,0.198 10 false 1W 0.781,3.635 1.094,3.833 0.313,0.198 10 false 4 1.979,7.906 4.271,8.083 2.292,0.177 10 false *: w/ Particulate Matter Sensor

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

According to the display on the GTS, select "Health Check".


d.

Check for currently output system DTCs.

Result:
Result Proceed to
DTC U010E87 is output A
DTC U02A387* is output B
DTC U029D87 is output C
DTC U029E87 is output D
2 or more of the following DTCs are simultaneously output: U02A387*, U029D87 or U029E87 E
DTC U010E87, U02A387, U029D87 and U029E87 is output simultaneously F


HINT:

*: w/ Particulate matter sensor




A

2.CHECK UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)

B

8.CHECK PARTICULATE MATTER SENSOR

C

11.CHECK NO. 1 NITROGEN OXIDES SENSOR

D

14.CHECK NO. 2 NITROGEN OXIDES SENSOR

E

17.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SENSOR)

F

29.CHECK ECM
2.CHECK UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
a.
A490660C04
0.292,0.813 0.698,1.063 0.406,0.25 0.646,1.552 1.396,1.135 true 0.656,1.75 1.406,1.333 true 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 0.375,1.5 0.833,1.698 0.458,0.198 10 false E01 0.375,1.708 0.833,1.906 0.458,0.198 10 false E02 0.427,0.854 0.74,1.052 0.313,0.198 10 false v6
*a Front view of wire harness connector
(to Urea Pump Assembly (Urea Pump Control ECU Integrated Urea Pump))


Disconnect the urea pump assembly (urea pump control ECU integrated urea pump).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
v6-1(E01) - Bodyground Always Below 1 Ω
v6-5(E02) - Bodyground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK UREA PUMP (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK UREA PUMP (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
a.
A490660C05
0.25,1.135 0.646,1.375 0.396,0.24 1.958,1.344 2.25,1.813 true 1.99,1.115 2.51,1.594 true 0.25,0.167 0.427,0.344 0.177,0.177 10 false *a 2.177,1.844 2.958,2.042 0.781,0.198 10 false 8 (+BU2) 0.396,1.156 0.781,1.375 0.385,0.219 10 false v6 2.479,1.625 3.26,1.823 0.781,0.198 10 false 4 (+BU1)
*a Front view of wire harness connector
(to Urea Pump Assembly (Urea Pump Control ECU Integrated Urea Pump))


Disconnect the urea pump assembly (urea pump control ECU integrated urea pump) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
v6-4(+BU1) - Body ground Engine switch on (IG) 11 to 14 V
v6-8(+BU2) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)

NG

7.INSPECT DCU RELAY
4.CHECK UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
a.
A490660C06
0.229,0.833 0.708,1.167 0.479,0.333 1.865,1.76 1.656,1.156 true 2.281,1.76 1.802,1.167 true 0.677,1.771 1.438,1.177 true 1.052,1.792 1.427,1.344 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.396,0.927 0.969,1.146 0.573,0.219 10 false v6 1.76,1.813 2.302,2.01 0.542,0.198 10 false CAN- 2.229,1.823 2.771,2.021 0.542,0.198 10 false CAN+ 0.875,1.802 1.417,2 0.542,0.198 10 false E02 0.51,1.813 1.052,2.01 0.542,0.198 10 false E01
*a Front view of wire harness connector
(to Urea Pump Control ECU)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
v6-3 (CAN+) or v6-2 (CAN-) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
v6-3 (CAN+) or v6-2 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
v6-3 (CAN+) or v6-2 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
v6-1 (E01) or v6-5 (E02) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω


Result:
Proceed to
OK
NG




OK

5.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
a.

Replace the urea pump assembly (urea pump control ECU integrated urea pump).

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off for 30 seconds or more.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.


Result:
Result Proceed to
U010E87 is output A
No DTC is output B



A

B

END

7.INSPECT DCU RELAY

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

8.CHECK PARTICULATE MATTER SENSOR
a.

Disconnect the particulate matter sensor connector.


b.

Turn the engine switch on (IG).


c.
A426728C08
1.469,0.198 1.948,0.531 0.479,0.333 1.125,1.771 1.365,1.271 true 2.573,1.833 2.177,1.271 true 1.573,1.813 1.677,1.302 true 2.104,1.833 1.906,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.625,0.292 1.938,0.49 0.313,0.198 10 false s8 2.573,1.833 3.031,2.031 0.458,0.198 10 false GND 0.771,1.833 1.313,2.031 0.542,0.198 10 false BATT 1.417,1.833 1.958,2.031 0.542,0.198 10 false CAN+ 1.99,1.833 2.531,2.031 0.542,0.198 10 false CAN-
*a Front view of wire harness connector
(to Particulate Matter Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
s8-1 (BATT) - s8-4 (GND) Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s8-2 (CAN+) - s8-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
s8-2 (CAN+) or s8-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
s8-2 (CAN+) or s8-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
s8-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.REPLACE PARTICULATE MATTER SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE PARTICULATE MATTER SENSOR
a.

Replace the particulate matter sensor assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>PARTICULATE MATTER SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CHECK DTC OUTPUT
10.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off for 30 seconds or more.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.


Result:
Result Proceed to
U02A387 is output A
No DTC is output B



A

B

END

11.CHECK NO. 1 NITROGEN OXIDES SENSOR
a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Turn the engine switch on (IG).


c.
A383897C91
1.469,0.198 1.948,0.531 0.479,0.333 1.25,1.792 1.448,1.271 true 2.479,1.76 2.219,1.271 true 2.167,1.771 1.948,1.281 true 1.573,1.76 1.719,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.552,0.292 2.125,0.51 0.573,0.219 10 false C181 2.083,1.781 2.542,1.979 0.458,0.198 10 false GND 2.458,1.781 3,1.979 0.542,0.198 10 false BATT 1.313,1.792 1.854,1.99 0.542,0.198 10 false CAN- 0.896,1.781 1.438,1.979 0.542,0.198 10 false CAN+
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C181-5 (BATT) - C181-4 (GND) Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C181-2 (CAN+) - C181-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
C181-2 (CAN+) or C181-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
C181-2 (CAN+) or C181-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
C181-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.REPLACE NO. 1 NITROGEN OXIDES SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE NO. 1 NITROGEN OXIDES SENSOR
a.

Replace the No. 1 nitrogen oxides sensor assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT
13.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off for 30 seconds or more.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.


Result:
Result Proceed to
U029D87 is output A
No DTC is output B



A

B

END

14.CHECK NO. 2 NITROGEN OXIDES SENSOR
a.

Disconnect the No. 2 nitrogen oxides sensor connector.


b.

Turn the engine switch on (IG).


c.
A383897C92
1.469,0.198 1.948,0.531 0.479,0.333 1.25,1.792 1.448,1.271 true 2.479,1.76 2.219,1.271 true 2.167,1.771 1.948,1.281 true 1.573,1.76 1.719,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.646,0.292 2.219,0.51 0.573,0.219 10 false s6 2.083,1.781 2.542,1.979 0.458,0.198 10 false GND 2.458,1.781 3,1.979 0.542,0.198 10 false BATT 1.313,1.792 1.854,1.99 0.542,0.198 10 false CAN- 0.896,1.781 1.438,1.979 0.542,0.198 10 false CAN+
*a Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
s6-5 (BATT) - s6-4 (GND) Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s6-2 (CAN+) - s6-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
s6-2 (CAN+) or s6-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
s6-2 (CAN+) or s6-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
s6-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.REPLACE NO. 2 NITROGEN OXIDES SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.REPLACE NO. 2 NITROGEN OXIDES SENSOR
a.

Replace the No. 2 nitrogen oxides sensor assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
16.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off for 30 seconds or more.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.


Result:
Result Proceed to
U029E87 is output A
No DTC is output B



A

B

END

17.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SENSOR)
A449209C08
1.448,0.104 1.948,0.385 0.5,0.281 2.219,0.104 2.719,0.385 0.5,0.281 4.813,0.104 5.313,0.385 0.5,0.281 1.781,1.448 2.198,1.031 true 4.333,1.458 4.75,1.042 true 2.719,1.458 2.458,1.052 true 5.656,1.448 5.396,1.042 true 1.542,0.167 2.073,0.49 0.531,0.323 10 false C181 2.406,0.156 2.833,0.458 0.427,0.302 10 false s6 4.979,0.156 5.313,0.479 0.333,0.323 10 false s8 1.99,0.156 2.323,0.479 0.333,0.323 10 false *a 5.354,0.156 5.688,0.479 0.333,0.323 10 false *c 2.771,0.177 3.104,0.5 0.333,0.323 10 false *b 2.635,1.5 3.125,1.729 0.49,0.229 10 false BATT 4.135,1.5 4.625,1.688 0.49,0.188 10 false BATT 1.542,1.5 1.99,1.698 0.448,0.198 10 false GND 5.604,1.5 6.094,1.74 0.49,0.24 10 false GND
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)
*b Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)
*c Front view of wire harness connector
(to Particulate Matter Sensor)
- -


a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Disconnect the No. 2 nitrogen oxides sensor connector.


c.

Disconnect the particulate matter sensor connector*.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C181-5 (BATT) - C181-4 (GND) Engine switch on (IG) 11 to 14 V
s6-5 (BATT) - s6-4 (GND) Engine switch on (IG) 11 to 14 V
s8-1 (BATT) - s8-4 (GND)* Engine switch on (IG) 11 to 14 V


HINT:

*: w/ Particulate matter sensor



e.

Reconnect the particulate matter sensor connector*.


f.

Reconnect the No. 2 nitrogen oxides sensor connector.


g.

Reconnect the No. 1 nitrogen oxides sensor connector.


Result:
Proceed to
OK
NG



OK

18.CHECK ECM

NG

28.INSPECT NO. 1 INTEGRATION RELAY (NOX PM RELAY)
18.CHECK ECM
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.
A449464C10
1.719,0.396 2.25,0.729 0.531,0.333 1.125,2.344 1.667,2.094 true 1.365,2.688 1.656,2.177 true 1.833,0.479 2.292,0.677 0.458,0.198 10 false G184 0.156,0.125 0.615,0.323 0.458,0.198 10 false *a 0.417,2.333 1.26,2.563 0.844,0.229 10 false 27 (CANU) 0.708,2.698 1.552,2.927 0.844,0.229 10 false 35 (CAND)
*a Rear view of wire harness connector
(to ECM Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G184-27 (CANU) - G184-35 (CAND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G184-27 (CANU) or G184-35 (CAND) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G184-27 (CANU) or G184-35 (CAND) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (w/ Particulate matter sensor) B
NG (w/o Particulate matter sensor) C



A

B

19.CHECK PARTICULATE MATTER SENSOR

C

24.CHECK NO. 1 NITROGEN OXIDES SENSOR
19.CHECK PARTICULATE MATTER SENSOR
a.
A491465C16
1.469,0.198 1.948,0.531 0.479,0.333 1.135,1.792 1.427,1.292 true 1.573,1.813 1.677,1.302 true 2.104,1.833 1.938,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.625,0.292 1.938,0.49 0.313,0.198 10 false s8 0.927,1.823 1.385,2.021 0.458,0.198 10 false GND 1.417,1.833 1.958,2.031 0.542,0.198 10 false CAN+ 1.99,1.833 2.531,2.031 0.542,0.198 10 false CAN-
*a Front view of wire harness connector
(to Particulate Matter Sensor)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the particulate matter sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s8-2 (CAN+) - s8-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
s8-2 (CAN+) or s8-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
s8-2 (CAN+) or s8-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
s8-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

20.REPLACE PARTICULATE MATTER SENSOR

NG

24.CHECK NO. 1 NITROGEN OXIDES SENSOR
20.REPLACE PARTICULATE MATTER SENSOR
a.

Replace the particulate matter sensor assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>PARTICULATE MATTER SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

21.CHECK DTC OUTPUT
21.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off for 30 seconds or more.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.


Result:
Result Proceed to
2 or more of the following DTCs are simultaneously output: U02A387*, U029D87 or U029E87 A
No DTC is output B


HINT:

*: w/ Particulate matter sensor



A

22.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
a.

Replace the urea pump assembly (urea pump control ECU integrated urea pump).

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

23.CHECK DTC OUTPUT
23.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off for 30 seconds or more.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.


Result:
Result Proceed to
2 or more of the following DTCs are simultaneously output: U02A387*, U029D87 or U029E87 A
No DTC is output B


HINT:

*: w/ Particulate matter sensor



A

B

END

24.CHECK NO. 1 NITROGEN OXIDES SENSOR
a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Turn the engine switch on (IG).


c.
A383897C91
1.469,0.198 1.948,0.531 0.479,0.333 1.25,1.792 1.448,1.271 true 2.479,1.76 2.219,1.271 true 2.167,1.771 1.948,1.281 true 1.573,1.76 1.719,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.552,0.292 2.125,0.51 0.573,0.219 10 false C181 2.083,1.781 2.542,1.979 0.458,0.198 10 false GND 2.458,1.781 3,1.979 0.542,0.198 10 false BATT 1.313,1.792 1.854,1.99 0.542,0.198 10 false CAN- 0.896,1.781 1.438,1.979 0.542,0.198 10 false CAN+
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C181-5 (BATT) - C181-4 (GND) Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C181-2 (CAN+) - C181-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
C181-2 (CAN+) or C181-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
C181-2 (CAN+) or C181-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
C181-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

25.REPLACE NO. 1 NITROGEN OXIDES SENSOR

NG

26.CHECK NO. 2 NITROGEN OXIDES SENSOR
25.REPLACE NO. 1 NITROGEN OXIDES SENSOR
a.

Replace the No. 1 nitrogen oxides sensor assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

21.CHECK DTC OUTPUT
26.CHECK NO. 2 NITROGEN OXIDES SENSOR
a.

Disconnect the No. 2 nitrogen oxides sensor connector.


b.

Turn the engine switch on (IG).


c.
A383897C92
1.469,0.198 1.948,0.531 0.479,0.333 1.25,1.792 1.448,1.271 true 2.479,1.76 2.219,1.271 true 2.167,1.771 1.948,1.281 true 1.573,1.76 1.719,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.646,0.292 2.219,0.51 0.573,0.219 10 false s6 2.083,1.781 2.542,1.979 0.458,0.198 10 false GND 2.458,1.781 3,1.979 0.542,0.198 10 false BATT 1.313,1.792 1.854,1.99 0.542,0.198 10 false CAN- 0.896,1.781 1.438,1.979 0.542,0.198 10 false CAN+
*a Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
s6-5 (BATT) - s6-4 (GND) Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s6-2 (CAN+) - s6-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
s6-2 (CAN+) or s6-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
s6-2 (CAN+) or s6-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
s6-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

27.REPLACE NO. 2 NITROGEN OXIDES SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.REPLACE NO. 2 NITROGEN OXIDES SENSOR
a.

Replace the No. 2 nitrogen oxides sensor assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

21.CHECK DTC OUTPUT
28.INSPECT NO. 1 INTEGRATION RELAY (NOX PM RELAY)

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE NO. 1 INTEGRATION RELAY

29.CHECK ECM
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.
A449464C10
1.719,0.396 2.25,0.729 0.531,0.333 1.125,2.344 1.667,2.094 true 1.365,2.688 1.656,2.177 true 1.833,0.479 2.292,0.677 0.458,0.198 10 false G184 0.156,0.125 0.615,0.323 0.458,0.198 10 false *a 0.417,2.333 1.26,2.563 0.844,0.229 10 false 27 (CANU) 0.708,2.698 1.552,2.927 0.844,0.229 10 false 35 (CAND)
*a Rear view of wire harness connector
(to ECM Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G184-27 (CANU) - G184-35 (CAND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G184-27 (CANU) or G184-35 (CAND) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G184-27 (CANU) or G184-35 (CAND) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (w/ Particulate matter sensor) B
NG (w/o Particulate matter sensor) C



A

B

30.CHECK PARTICULATE MATTER SENSOR

C

35.CHECK NO. 1 NITROGEN OXIDES SENSOR
30.CHECK PARTICULATE MATTER SENSOR
a.
A491465C16
1.469,0.198 1.948,0.531 0.479,0.333 1.135,1.792 1.427,1.292 true 1.573,1.813 1.677,1.302 true 2.104,1.833 1.938,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.625,0.292 1.938,0.49 0.313,0.198 10 false s8 0.927,1.823 1.385,2.021 0.458,0.198 10 false GND 1.417,1.833 1.958,2.031 0.542,0.198 10 false CAN+ 1.99,1.833 2.531,2.031 0.542,0.198 10 false CAN-
*a Front view of wire harness connector
(to Particulate Matter Sensor)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the particulate matter sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s8-2 (CAN+) - s8-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
s8-2 (CAN+) or s8-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
s8-2 (CAN+) or s8-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
s8-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

31.REPLACE PARTICULATE MATTER SENSOR

NG

35.CHECK NO. 1 NITROGEN OXIDES SENSOR
31.REPLACE PARTICULATE MATTER SENSOR
a.

Replace the particulate matter sensor assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>PARTICULATE MATTER SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

32.CHECK DTC OUTPUT
32.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off for 30 seconds or more.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.


Result:
Result Proceed to
2 or more of the following DTCs are simultaneously output:U010E87, U02A387*, U029D87 or U029E87 A
No DTC is output B


HINT:

*: w/ Particulate matter sensor



A

33.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
a.

Replace the urea pump assembly (urea pump control ECU integrated urea pump).

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

34.CHECK DTC OUTPUT
34.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off for 30 seconds or more.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.


Result:
Result Proceed to
2 or more of the following DTCs are simultaneously output:U010E87, U02A387*, U029D87 or U029E87 A
No DTC is output B


HINT:

*: w/ Particulate matter sensor



A

B

END

35.CHECK NO. 1 NITROGEN OXIDES SENSOR
a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Turn the engine switch on (IG).


c.
A383897C91
1.469,0.198 1.948,0.531 0.479,0.333 1.25,1.792 1.448,1.271 true 2.479,1.76 2.219,1.271 true 2.167,1.771 1.948,1.281 true 1.573,1.76 1.719,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.552,0.292 2.125,0.51 0.573,0.219 10 false C181 2.083,1.781 2.542,1.979 0.458,0.198 10 false GND 2.458,1.781 3,1.979 0.542,0.198 10 false BATT 1.313,1.792 1.854,1.99 0.542,0.198 10 false CAN- 0.896,1.781 1.438,1.979 0.542,0.198 10 false CAN+
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C181-5 (BATT) - C181-4 (GND) Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C181-2 (CAN+) - C181-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
C181-2 (CAN+) or C181-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
C181-2 (CAN+) or C181-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
C181-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

36.REPLACE NO. 1 NITROGEN OXIDES SENSOR

NG

37.CHECK NO. 2 NITROGEN OXIDES SENSOR
36.REPLACE NO. 1 NITROGEN OXIDES SENSOR
a.

Replace the No. 1 nitrogen oxides sensor assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

32.CHECK DTC OUTPUT
37.CHECK NO. 2 NITROGEN OXIDES SENSOR
a.

Disconnect the No. 2 nitrogen oxides sensor connector.


b.

Turn the engine switch on (IG).


c.
A383897C92
1.469,0.198 1.948,0.531 0.479,0.333 1.25,1.792 1.448,1.271 true 2.479,1.76 2.219,1.271 true 2.167,1.771 1.948,1.281 true 1.573,1.76 1.719,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.646,0.292 2.219,0.51 0.573,0.219 10 false s6 2.083,1.781 2.542,1.979 0.458,0.198 10 false GND 2.458,1.781 3,1.979 0.542,0.198 10 false BATT 1.313,1.792 1.854,1.99 0.542,0.198 10 false CAN- 0.896,1.781 1.438,1.979 0.542,0.198 10 false CAN+
*a Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
s6-5 (BATT) - s6-4 (GND) Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s6-2 (CAN+) - s6-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
s6-2 (CAN+) or s6-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
s6-2 (CAN+) or s6-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
s6-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

38.REPLACE NO. 2 NITROGEN OXIDES SENSOR

NG

39.CHECK UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
38.REPLACE NO. 2 NITROGEN OXIDES SENSOR
a.

Replace the No. 2 nitrogen oxides sensor assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

32.CHECK DTC OUTPUT
39.CHECK UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
a.
A490660C06
0.229,0.833 0.708,1.167 0.479,0.333 1.865,1.76 1.656,1.156 true 2.281,1.76 1.802,1.167 true 0.677,1.771 1.438,1.177 true 1.052,1.792 1.427,1.344 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.396,0.927 0.969,1.146 0.573,0.219 10 false v6 1.76,1.813 2.302,2.01 0.542,0.198 10 false CAN- 2.229,1.823 2.771,2.021 0.542,0.198 10 false CAN+ 0.875,1.802 1.417,2 0.542,0.198 10 false E02 0.51,1.813 1.052,2.01 0.542,0.198 10 false E01
*a Front view of wire harness connector
(to Urea Pump Control ECU)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
v6-3 (CAN+) or v6-2 (CAN-) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
v6-3 (CAN+) or v6-2 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
v6-3 (CAN+) or v6-2 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
v6-1 (E01) or v6-5 (E02) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω


Result:
Proceed to
OK
NG




OK

40.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

40.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
a.

Replace the urea pump assembly (urea pump control ECU integrated urea pump).

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

32.CHECK DTC OUTPUT