P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Also covers:
- P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)
- P0057 Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2)
- P0058 Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2)
- P0141 Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
- P0161 Oxygen Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
Refer to DTC P0136 (Click here).- HINT:
- Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.
- When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the Heated Oxygen (HO2) sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.
- The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The HO2 sensor heater circuit uses a relay on the +B side of the circuit.


- Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.
DTC Code
DTC Detection Condition
Trouble Area
P0037
P0057
The Heated Oxygen (HO2) sensor heater (bank 1, 2 sensor 2) current is below 0.3 A (1 trip detection logic).
- Open in Heated Oxygen (HO2) sensor heater (bank 1, 2 sensor 2) circuit
- HO2 sensor heater (bank 1, 2 sensor 2)
- EFI NO. 2 fuse
- ECM
P0038
P0058
The Heated Oxygen (HO2) sensor heater (bank 1, 2 sensor 2) current is higher than 2 A (1 trip detection logic).
- Short in HO2 sensor heater (bank 1, 2 sensor 2) circuit
- HO2 sensor heater (bank 1, 2 sensor 2)
- EFI NO. 2 fuse
- ECM
P0141
P0161
The cumulative heater resistance correction value exceeds the acceptable threshold (2 trip detection logic).
- Open or short in HO2 sensor heater (bank 1, 2 sensor 2) circuit
- HO2 sensor heater (bank 1, 2 sensor 2)
- EFI NO. 2 fuse
- ECM
- Open in Heated Oxygen (HO2) sensor heater (bank 1, 2 sensor 2) circuit
- HINT:
- Bank 1 refers to the bank that includes the No. 1 cylinder.
- Bank 2 refers to the bank that does not include the No. 1 cylinder.
- Sensor 1 refers to the sensor closest to the engine assembly.
- Sensor 2 refers to the sensor farthest away from the engine assembly.
- Bank 1 refers to the bank that includes the No. 1 cylinder.
MONITOR DESCRIPTION
The sensing portion of the Heated Oxygen (HO2) sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.- Heated oxygen sensor heater range check (P0037, P0038, P0057 and P0058):
- The ECM monitors the current applied to the HO2 sensor heater to check the heater for malfunctions. If the current is below the threshold value, the ECM will determine that there is an open circuit in the heater. If the current is above the threshold value, the ECM will determine that there is a short circuit in the heater.
- Example:
- The ECM stores DTC P0038 or P0058 when the current in the HO2 sensor heater is higher than 2 A. Conversely, when the heater current is below 0.3 A, DTC P0037 or P0057 is stored.
- The ECM monitors the current applied to the HO2 sensor heater to check the heater for malfunctions. If the current is below the threshold value, the ECM will determine that there is an open circuit in the heater. If the current is above the threshold value, the ECM will determine that there is a short circuit in the heater.
- Heated oxygen sensor heater performance (P0141 and P0161):
- After the accumulated heater ON time exceeds 100 seconds, the ECM calculates the heater resistance using the battery voltage and the current applied to the heater. If the resistance is above the threshold value, the ECM will determine that there is a malfunction in the HO2 sensor heater and store DTCs P0141 and P0161.
- After the accumulated heater ON time exceeds 100 seconds, the ECM calculates the heater resistance using the battery voltage and the current applied to the heater. If the resistance is above the threshold value, the ECM will determine that there is a malfunction in the HO2 sensor heater and store DTCs P0141 and P0161.
WIRING DIAGRAM
Refer to DTC P0136 (Click here).INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Disconnect the heated oxygen (HO2) sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for Bank 1 Sensor 2 Tester Connection
Condition
Specified Condition
1 (HT1B) - 2 (+B)
20°C (68°F)
11 to 16 Ω
1 (HT1B) - 4 (E2)
Always
10 kΩ or higher
for Bank 2 Sensor 2 Tester Connection
Condition
Specified Condition
1 (HT2B) - 2 (+B)
20°C (68°F)
11 to 16 Ω
1 (HT2B) - 4 (E2)
Always
10 kΩ or higher
|
|
||||
| OK | |
| 2. CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR) |
![]() ![]() |
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
for Bank 1 Sensor 1 Tester Connection
Switch Condition
Specified Condition
C20-2 (+B) - Body ground
Ignition switch ON
11 to 14 V
for Bank 2 Sensor 1 Tester Connection
Switch Condition
Specified Condition
C21-2 (+B) - Body ground
Ignition switch ON
11 to 14 V
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
Disconnect the ECM connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
for LHD Tester Connection
Condition
Specified Condition
C20-1 (HT1B) - C45-48 (HT1B)
Always
Below 1 Ω
C21-1 (HT2B) - C45-47 (HT2B)
Always
Below 1 Ω
for RHD Tester Connection
Condition
Specified Condition
C20-1 (HT1B) - C46-48 (HT1B)
Always
Below 1 Ω
C21-1 (HT2B) - C46-47 (HT2B)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
for LHD Tester Connection
Condition
Specified Condition
C20-1 (HT1B) or C45-48 (HT1B) - Body ground
Always
10 kΩ or higher
C21-1 (HT2B) or C45-47 (HT2B) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
C20-1 (HT1B) or C46-48 (HT1B) - Body ground
Always
10 kΩ or higher
C21-1 (HT2B) or C46-47 (HT2B) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 4. INSPECT FUSE (EFI NO. 2) |
Remove the EFI NO. 2 fuse from the engine room relay block.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
EFI NO. 2 fuse
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - EFI NO. 2 FUSE) |
Remove the EFI NO. 2 fuse from the engine room relay block.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
C20-2 (+B) - EFI NO. 2 fuse (2)
Always
Below 1 Ω
C21-2 (+B) - EFI NO. 2 fuse (2)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
C20-2 (+B) or EFI NO. 2 fuse (2) - Body ground
Always
10 kΩ or higher
C21-2 (+B) or EFI NO. 2 fuse (2) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - EFI NO. 2 FUSE) |
Remove the EFI NO. 2 fuse from the engine room relay block.

Remove the integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
EFI NO. 2 fuse (1) - 1B-4
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
EFI NO. 2 fuse (1) or 1B-4 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||

