2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

ON-VEHICLE INSPECTION

Inspection · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


INSPECT ENGINE IDLE SPEED

NOTICE:
  1. Turn all the electrical systems and the A/C off.
  2. When checking the idle speed, move the shift lever to neutral.

HINT:
  1. For more information about the intelligent tester, refer to its operator's manual.
  2. If an intelligent tester is not available, use a tachometer tester probe as a substitute.

  1. When using the intelligent tester:

    1. Warm up the engine.

    2. Connect the intelligent tester to the DLC3.

    3. Enter the following menus:
      Powertrain / Engine / Data List / Engine Speed.

      HINT:
      Refer to the intelligent tester operator's manual for help selecting the Data List.

    4. Inspect the engine idle speed.

      Standard Idle Speed:
      Item
      Specified Condition
      for Automatic Transmission
      550 to 650 rpm
      for Manual Transmission
      500 to 600 rpm

    5. Disconnect the intelligent tester from the DLC3.

  1. When not using the intelligent tester:

    1. Warm up and stop the engine.

    2. A167780E01
      Connect a tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.
      SST
      09843-18030  

    3. Inspect the engine idle speed.

      Standard Idle Speed:
      Item
      Specified Condition
      for Automatic Transmission
      550 to 650 rpm
      for Manual Transmission
      500 to 600 rpm

    4. Disconnect the tester probe from terminal 9 (TAC) of the DLC3.


INSPECT MAXIMUM ENGINE SPEED
  1. Start the engine.

  1. Fully depress the accelerator pedal.

  1. Check the maximum engine speed.

    Maximum engine speed:
    4700 to 4900 rpm


INSPECT COMPRESSION
  1. Warm up and stop the engine.

  1. Remove the 8 glow plugs (Click here).

  1. Disconnect all connectors from the 8 injectors.

  1. Inspect the cylinder compression pressure.

    1. A177330E01
      Insert SST (attachment) into the glow plug hole.
      SST
      09992-00026   (09992-00410, 09992-00211)

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    2. Connect SST (compression gauge) to SST (attachment).

    3. While cranking the engine, measure the compression pressure.

      Standard compression pressure (normal condition):
      2700 kPa (27.5 kgf/cm2, 392 psi)

      Minimum compression pressure:
      2200 kPa (22.4 kgf/cm2, 319 psi)

      Difference between each cylinder:
      500 kPa (5.1 kgf/cm2, 73 psi) or less

      NOTICE:
      1. Use a fully-charged battery so the engine speed can be increased to 280 rpm or more.
      2. Inspect the other cylinders in the same way.
      3. Measure the compression as quickly as possible.

    4. If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the glow plug holes. Then inspect the cylinder compression again.
      If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.
      If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.

    5. Remove SST (attachment and compression gauge).

  1. Connect all connectors to the 8 injectors.

  1. Install the 8 glow plugs (Click here).

← REPAIR (Sep 2011 – Dec 2011)ON-VEHICLE INSPECTION (from Jan 2012) →