ON-VEHICLE INSPECTION
Inspection · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| INSPECT ENGINE IDLE SPEED |
- NOTICE:
- Turn all the electrical systems and the A/C off.
- When checking the idle speed, move the shift lever to neutral.
- Turn all the electrical systems and the A/C off.
- HINT:
- For more information about the GTS, refer to its operator's manual.
- If an GTS is not available, use a tachometer tester probe as a substitute.
- For more information about the GTS, refer to its operator's manual.
When using the GTS:
Warm up the engine.
Connect the GTS to the DLC3.
Enter the following menus:
Powertrain / Engine / Data List / Engine Speed.- HINT:
- Refer to the GTS operator's manual for help selecting the Data List.
Inspect the engine idle speed.
- Standard Idle Speed:
Item
Specified Condition
for Automatic Transmission
550 to 750 rpm
for Manual Transmission
500 to 600 rpm
Disconnect the GTS from the DLC3.
When not using the GTS:
Warm up and stop the engine.
Connect a tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.

- SST
- 09843-18040
Text in Illustration *a
Front view of DLC3
Inspect the engine idle speed.
- Standard Idle Speed:
Item
Specified Condition
for Automatic Transmission
550 to 750 rpm
for Manual Transmission
500 to 600 rpm
Disconnect the tester probe from terminal 9 (TAC) of the DLC3.
| INSPECT MAXIMUM ENGINE SPEED |
Start the engine.
Fully depress the accelerator pedal.
Check the maximum engine speed.
- Maximum engine speed:
- 4700 to 4900 rpm
| INSPECT COMPRESSION |
Warm up and stop the engine.
Disconnect the cable from the negative (-) battery terminal.
Remove the No. 1 glow plug connector.
w/ Intercooler:
Remove the intercooler assembly (Click here).Remove the injection pipes (Click here).
Remove the No. 1 glow plug connector.
Reinstall the injection pipes (Click here).
Remove the 8 glow plugs (Click here).
Disconnect all connectors from the 8 injectors.
Connect the cable to the negative (-) battery terminal.
Inspect the cylinder compression pressure.
Insert SST (attachment) into the glow plug hole.

- SST
- 09992-00026
(09992-00410, 09992-00211)
- Torque:
- 13 N*m{ 133 kgf*cm , 10 ft.*lbf }
Text in Illustration *1
SST (Compression Gauge)
*2
SST (Attachment)
Connect SST (compression gauge) to SST (attachment).
While cranking the engine, measure the compression pressure.
- Standard compression pressure (normal condition):
- 2700 kPa (27.5 kgf/cm2, 392 psi)
- Minimum compression pressure:
- 2200 kPa (22.4 kgf/cm2, 319 psi)
- Difference between each cylinder:
- 500 kPa (5.1 kgf/cm2, 73 psi) or less
- NOTICE:
- Use a fully-charged battery so the engine speed can be increased to 280 rpm or more.
- Inspect the other cylinders in the same way.
- Measure the compression as quickly as possible.
- Use a fully-charged battery so the engine speed can be increased to 280 rpm or more.
If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the glow plug holes. Then inspect the cylinder compression again.
If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.
If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.Remove SST (attachment and compression gauge).
Disconnect the cable from the negative (-) battery terminal.
Connect all connectors to the 8 injectors.
Install the 8 glow plugs (Click here).
Install the No. 1 glow plug connector.
Remove the injection pipes (Click here).
Reinstall the No. 1 glow plug connector.
Install the injection pipes (Click here).
w/ Intercooler:
Install the intercooler assembly (Click here).
