2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0300 Random / Multiple Cylinder Misfire Detected

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

A093767E03
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emission levels. High concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the Camshaft Position (CMP) sensor and the Crankshaft Position (CKP) sensor. The CMP sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted as when the crankshaft rotation speed variations exceed predetermined thresholds.
If the misfire rate exceeds the threshold level, the ECM illuminates the MIL and stores a DTC.
DTC Code
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinders occurs and one of the following conditions below is detected (2 trip detection logic):
  1. A high temperature misfire occurs in the Three-Way Catalytic Converter (TWC) (MIL blinks).
  2. An emission deterioration misfire occurs (MIL illuminates).
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Fuel injector
  6. Fuel pressure
  7. Mass Air Flow (MAF) meter
  8. Engine Coolant Temperature (ECT) sensor
  9. Compression pressure
  10. Valve clearance
  11. Valve timing
  12. PCV valve and hose
  13. PCV hose connections
  14. Air induction system
  15. ECM
P0301
P0302
P0303
P0304
P0305
P0306
P0307
P0308
Misfiring of a specific cylinder occurs and one of the following conditions below is detected (2 trip detection logic):
  1. A high temperature misfire occurs in the Three-Way Catalytic Converter (TWC) (MIL blinks).
  2. An emission deterioration misfire occurs (MIL illuminates).
When multiple DTCs for misfiring cylinders are stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
  1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 130 to 160 misfires per 1000 crankshaft revolutions) occurs once.
  2. An excessive misfiring rate (approximately 130 to 160 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL and stores a DTC when either one of the following conditions, which could cause damage to the Three-Way Catalytic Converter (TWC), is detected (2 trip detection logic).
  1. At a high engine speed, a catalyst damage misfire, which is monitored every 200 crankshaft revolutions, occurs once.
  2. At a normal engine speed, a catalyst damage misfire, which is monitored every 200 crankshaft revolutions, occurs 3 times.

HINT:
If a catalyst damage misfire occurs, the ECM informs the driver by flashing the MIL.


WIRING DIAGRAM

A182116E01
A162767E04
A162768E03

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the engine switch on (IG).
  3. Turn the tester on.
  4. Record the DTC(s) and freeze frame data.
  5. Using the tester, switch the ECM from normal mode to check mode (Click here).
  6. Read the misfire counts of each cylinder (cylinder No. 1 to No. 8) with the engine in an idling condition. If any misfire count is displayed, skip the following confirmation driving pattern.
  7. Drive the vehicle several times with the conditions, such as engine speed and engine load, shown in Misfire RPM and Misfire Load in the Data List.

    HINT:
    In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, with the Misfire RPM and Misfire Load in the Data List.
    Engine Speed
    Duration
    Idling
    3.5 minutes or more
    1000
    3 minutes or more
    2000
    1.5 minutes or more
    3000
    1 minute or more

  8. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the engine switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be cleared.

  9. Record the DTC(s), freeze frame data and misfire counts.
  10. Turn the engine switch off and wait for at least 5 seconds.

INSPECTION PROCEDURE

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors is considered to be a possible cause of the problem:
    1. The fuel level is low.
    2. Improper fuel is used.
    3. The spark plugs are dirty.
  5. After finishing repairs, check that no misfires occur in each cylinder (cylinder No. 1, No. 2, No. 3, No. 4, No. 5, No. 6, No. 7 and No. 8).
  6. Be sure to confirm that no misfiring cylinder DTCs are output again by conducting the confirmation driving pattern, after the repairs.
  7. For 6 and 8 cylinder engines, the ECM intentionally does not store the specific misfiring cylinder DTCs at high engine speed. If misfires only occur during high engine speed driving, only DTC P0300 is stored.
    In the event of DTC P0300 being output, perform the following operations:
    1. Clear the DTC (Click here).
    2. Start the engine and conduct the confirmation driving pattern.
    3. Read the misfiring rates of each cylinder or DTC(s) using the tester.
    4. Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.
    5. After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not output.
  8. When either Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-20%, the air-fuel ratio may be rich (-20% or less) or lean (+20% or more).
  9. When the Coolant Temp in the freeze frame data is below 75°C (167°F), the misfires occurred only while warming up the engine.
  10. An extremely imbalanced drive wheel can cause body vibration, which may cause misfire DTC(s) to be stored.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 is output
    A
    P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 and other DTCs are output
    B

HINT:
If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and P0308 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the intelligent tester the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load values.

    HINT:
    The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.


NEXT


3. CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections.

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE (Click here)
OK


4. READ VALUE USING INTELLIGENT TESTER (MISFIRE COUNT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Clear DTCs (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire / Cylinder #1 Misfire Count, #2, #3, #4, #5, #6, #7 and #8.

  1. Allow the engine to idle.

  1. Read each value for Cylinder #1 Misfire Count to #8 displayed on the tester. If no misfire counts occur in any cylinders, perform the following procedures:

    1. Move the shift lever to D.

    2. Check the Cylinder #1 Misfire Count to #8.

    3. If misfire counts are still not displayed, perform procedure "A" and "B" and then check the misfire counts again.

  1. Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read value using intelligent tester (Misfire RPM and Misfire Load)" procedures above (procedure "A").

  1. Read the Cylinder #1 Misfire Count to #8 or DTCs displayed on the tester (procedure "B").

    Result 
    Misfire Count
    Proceed to
    Most misfires occur in only 1 or 2 cylinders
    A
    3 cylinders or more have equal misfire counts
    B

    HINT:
    1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
    2. If the freeze frame data record of the ECT is below 75°C (167°F), the misfire may be detected only when the engine is cold.
    3. If the freeze frame data record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 17
A


5. CHECK SPARK PLUG
A126880E01
  1. Remove the ignition coil and the spark plug of the misfiring cylinder (Click here).

  1. Measure the spark plug electrode gap.

    Standard gap:
    1.0 to 1.1 mm (0.039 to 0.043 in.)

  1. Check the electrode for carbon deposits.

    Recommended Spark Plug: 
    Manufacturer
    Product
    DENSO
    SK20R11
    NGK
    IFR6A11

    NOTICE:
    If the electrode gap is larger than standard, replace the spark plug. Do not adjust the electrode gap.



NG
REPLACE SPARK PLUG (Click here)
OK


6. CHECK FOR SPARKS AND IGNITION
A088862E01
  1. Disconnect the fuel injector connectors to prevent the engine from starting.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

  1. Remove the ignition coil from the cylinder head (Click here).

  1. Install the spark plug onto the ignition coil.

  1. Attach the spark plug assembly to the cylinder head.

  1. Crank the engine for less than 2 seconds and check the spark.

    OK:
    Sparks jump across electrode gap.

  1. Install the ignition coil.

  1. Reconnect the injector connectors.



NG
Go to step 29
OK


7. CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder (Click here).



NG
REPAIR ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


8. CHECK HARNESS AND CONNECTOR (ECM - FUEL INJECTOR)
A181795E01
  1. Disconnect the fuel injector connector (of the misfiring cylinder).

  1. Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    C5-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 2
    C16-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 3
    C7-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 4
    C14-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 5
    C9-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 6
    C12-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 7
    C52-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 8
    C54-1 - Ground
    Engine switch on (IG)
    11 to 14 V

  1. Turn the engine switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    C5-2 - Body ground
    Always
    10 kΩ or higher
    C5-2 - C45-86 (#10)
    Always
    Below 1 Ω
    No. 2
    C16-2 - Ground
    Always
    10 kΩ or higher
    C16-2 - C45-109 (#20)
    Always
    Below 1 Ω
    No. 3
    C7-2 - Ground
    Always
    10 kΩ or higher
    C7-2 - C45-85 (#30)
    Always
    Below 1 Ω
    No. 4
    C14-2 - Ground
    Always
    10 kΩ or higher
    C14-2 - C45-108 (#40)
    Always
    Below 1 Ω
    No. 5
    C9-2 - Ground
    Always
    10 kΩ or higher
    C9-2 - C45-84 (#50)
    Always
    Below 1 Ω
    No. 6
    C12-2 - Ground
    Always
    10 kΩ or higher
    C12-2 - C45-107 (#60)
    Always
    Below 1 Ω
    No. 7
    C52-2 - Ground
    Always
    10 kΩ or higher
    C52-2 - C45-83 (#70)
    Always
    Below 1 Ω
    No. 8
    C54-2 - Ground
    Always
    10 kΩ or higher
    C54-2 - C45-106 (#80)
    Always
    Below 1 Ω

    Standard Resistance (for RHD):
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    C5-2 - Body ground
    Always
    10 kΩ or higher
    C5-2 - C46-86 (#10)
    Always
    Below 1 Ω
    No. 2
    C16-2 - Ground
    Always
    10 kΩ or higher
    C16-2 - C46-109 (#20)
    Always
    Below 1 Ω
    No. 3
    C7-2 - Ground
    Always
    10 kΩ or higher
    C7-2 - C46-85 (#30)
    Always
    Below 1 Ω
    No. 4
    C14-2 - Ground
    Always
    10 kΩ or higher
    C14-2 - C46-108 (#40)
    Always
    Below 1 Ω
    No. 5
    C9-2 - Ground
    Always
    10 kΩ or higher
    C9-2 - C46-84 (#50)
    Always
    Below 1 Ω
    No. 6
    C12-2 - Ground
    Always
    10 kΩ or higher
    C12-2 - C46-107 (#60)
    Always
    Below 1 Ω
    No. 7
    C52-2 - Ground
    Always
    10 kΩ or higher
    C52-2 - C46-83 (#70)
    Always
    Below 1 Ω
    No. 8
    C54-2 - Ground
    Always
    10 kΩ or higher
    C54-2 - C46-106 (#80)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)
A136305E47
  1. Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage (for LHD):
    Tester Connection
    Switch Condition
    Specified Condition
    C45-86 (#10) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C45-109 (#20) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C45-85 (#30) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C45-108 (#40) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C45-84 (#50) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C45-107 (#60) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C45-83 (#70) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C45-106 (#80) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V

    Standard Voltage (for RHD):
    Tester Connection
    Switch Condition
    Specified Condition
    C46-86 (#10) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C46-109 (#20) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C46-85 (#30) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C46-108 (#40) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C46-84 (#50) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C46-107 (#60) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C46-83 (#70) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C46-106 (#80) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)
OK


10. CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).



NG
REPLACE FUEL INJECTOR (Click here)
OK


11. CHECK VALVE CLEARANCE OF MISFIRING CYLINDER
  1. Check the valve clearance (Click here).



NG
ADJUST VALVE CLEARANCE (Click here)
OK


12. CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage (Click here).

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM (Click here)
OK


13. CHECK VALVE TIMING
A178910E01
  1. Remove the drive belt (Click here).

  1. Remove the timing belt cover LH and RH (Click here).

  1. Turn the crankshaft to align the matchmarks of the crankshaft.

  1. Align the notch of the crankshaft pulley with the "0" position.

  1. Confirm whether the matchmarks of the camshaft pulley and cylinder head cover are facing each other.

  1. If the matchmarks are not facing each other, turn the crankshaft clockwise by 360°. Confirm again if the matchmarks are facing each other.

    OK:
    The matchmarks of the camshaft pulley and the cylinder head cover face each other when the notch of the crankshaft pulley is in the "0" position.



NG
ADJUST VALVE TIMING (Click here)
OK


14. CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER
OK


15. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: Between 80°C and 100°C (167°F and 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


16. INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK

REPLACE ECM (Click here)

17. CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage (Click here).

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM (Click here)
OK


18. CHECK VALVE TIMING
A178910E01
  1. Remove the drive belt (Click here).

  1. Remove the timing belt cover LH and RH (Click here).

  1. Turn the crankshaft to align the matchmarks of the crankshaft.

  1. Align the notch of the crankshaft pulley with the "0" position.

  1. Confirm whether the matchmarks of the camshaft pulley and cylinder head cover are facing each other.

  1. If the matchmarks are not facing each other, turn the crankshaft clockwise by 360°. Confirm again if the matchmarks are facing each other.

    OK:
    The matchmarks of the camshaft pulley and the cylinder head cover face each other when the notch of the crankshaft pulley is in the "0" position.



NG
ADJUST VALVE TIMING (Click here)
OK


19. CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER
OK


20. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: Between 80°C and 100°C (167°F and 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


21. INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


22. CHECK SPARK PLUG
A126880E01
  1. Remove the ignition coil and the spark plug of the misfiring cylinder (Click here).

  1. Measure the spark plug electrode gap.

    Standard gap:
    1.0 to 1.1 mm (0.039 to 0.043 in.)

  1. Check the electrode for carbon deposits.

    Recommended Spark Plug: 
    Manufacturer
    Product
    DENSO
    SK20R11
    NGK
    IFR6A11

    NOTICE:
    If the electrode gap is larger than standard, replace the spark plug. Do not adjust the electrode gap.



NG
REPLACE SPARK PLUG (Click here)
OK


23. CHECK FOR SPARKS AND IGNITION
A088862E01
  1. Disconnect the fuel injector connectors to prevent the engine from starting.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

  1. Remove the ignition coil from the cylinder head (Click here).

  1. Install the spark plug onto the ignition coil.

  1. Attach the spark plug assembly to the cylinder head.

  1. Crank the engine for less than 2 seconds and check the spark.

    OK:
    Sparks jump across electrode gap.

  1. Install the ignition coil.

  1. Reconnect the injector connectors.



NG
Go to step 29
OK


24. CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder (Click here).



NG
REPAIR ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


25. CHECK HARNESS AND CONNECTOR (ECM - FUEL INJECTOR)
A181795E01
  1. Disconnect the fuel injector connector (of the misfiring cylinder).

  1. Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    C5-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 2
    C16-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 3
    C7-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 4
    C14-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 5
    C9-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 6
    C12-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 7
    C52-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 8
    C54-1 - Ground
    Engine switch on (IG)
    11 to 14 V

  1. Turn the engine switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    C5-2 - Body ground
    Always
    10 kΩ or higher
    C5-2 - C45-86 (#10)
    Always
    Below 1 Ω
    No. 2
    C16-2 - Ground
    Always
    10 kΩ or higher
    C16-2 - C45-109 (#20)
    Always
    Below 1 Ω
    No. 3
    C7-2 - Ground
    Always
    10 kΩ or higher
    C7-2 - C45-85 (#30)
    Always
    Below 1 Ω
    No. 4
    C14-2 - Ground
    Always
    10 kΩ or higher
    C14-2 - C45-108 (#40)
    Always
    Below 1 Ω
    No. 5
    C9-2 - Ground
    Always
    10 kΩ or higher
    C9-2 - C45-84 (#50)
    Always
    Below 1 Ω
    No. 6
    C12-2 - Ground
    Always
    10 kΩ or higher
    C12-2 - C45-107 (#60)
    Always
    Below 1 Ω
    No. 7
    C52-2 - Ground
    Always
    10 kΩ or higher
    C52-2 - C45-83 (#70)
    Always
    Below 1 Ω
    No. 8
    C54-2 - Ground
    Always
    10 kΩ or higher
    C54-2 - C45-106 (#80)
    Always
    Below 1 Ω

    Standard Resistance (for RHD):
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    C5-2 - Body ground
    Always
    10 kΩ or higher
    C5-2 - C46-86 (#10)
    Always
    Below 1 Ω
    No. 2
    C16-2 - Ground
    Always
    10 kΩ or higher
    C16-2 - C46-109 (#20)
    Always
    Below 1 Ω
    No. 3
    C7-2 - Ground
    Always
    10 kΩ or higher
    C7-2 - C46-85 (#30)
    Always
    Below 1 Ω
    No. 4
    C14-2 - Ground
    Always
    10 kΩ or higher
    C14-2 - C46-108 (#40)
    Always
    Below 1 Ω
    No. 5
    C9-2 - Ground
    Always
    10 kΩ or higher
    C9-2 - C46-84 (#50)
    Always
    Below 1 Ω
    No. 6
    C12-2 - Ground
    Always
    10 kΩ or higher
    C12-2 - C46-107 (#60)
    Always
    Below 1 Ω
    No. 7
    C52-2 - Ground
    Always
    10 kΩ or higher
    C52-2 - C46-83 (#70)
    Always
    Below 1 Ω
    No. 8
    C54-2 - Ground
    Always
    10 kΩ or higher
    C54-2 - C46-106 (#80)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


26. INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)
A136305E47
  1. Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage (for LHD):
    Tester Connection
    Switch Condition
    Specified Condition
    C45-86 (#10) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C45-109 (#20) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C45-85 (#30) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C45-108 (#40) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C45-84 (#50) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C45-107 (#60) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C45-83 (#70) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C45-106 (#80) - C45-43 (E01)
    Engine switch on (IG)
    11 to 14 V

    Standard Voltage (for RHD):
    Tester Connection
    Switch Condition
    Specified Condition
    C46-86 (#10) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C46-109 (#20) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C46-85 (#30) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C46-108 (#40) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C46-84 (#50) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C46-107 (#60) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C46-83 (#70) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V
    C46-106 (#80) - C46-43 (E01)
    Engine switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)
OK


27. CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).



NG
REPLACE FUEL INJECTOR (Click here)
OK


28. CHECK VALVE CLEARANCE OF MISFIRING CYLINDER
  1. Check the valve clearance (Click here).



NG
ADJUST VALVE CLEARANCE (Click here)
OK

REPLACE ECM (Click here)

29. CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
  1. Replace the installed spark plug with a spark plug that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil and connect the ignition coil connector.

    2. Disconnect the injector connector.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
Go to step 30
OK

REPLACE SPARK PLUG (Click here)

30. CHANGE TO NORMAL IGNITION COIL AND CHECK SPARK OF MISFIRING CYLINDER
  1. Replace the ignition coil with an ignition coil that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil and connect the ignition coil connector.

    2. Disconnect the injector connector.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
REPLACE ECM (Click here)
OK

REPLACE IGNITION COIL (Click here)


← P0230 Fuel Pump Primary Circuit (Sep 2011 – Dec 2011)P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) (+ P0328, P0332, P0333) (Sep 2011 – Dec 2011) →