2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0230 Fuel Pump Primary Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

When a malfunction in the fuel pump circuit is detected, DTC P0230 is stored.
The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed between 3 settings. The fuel pump ECU also has a self-diagnosis function. Based on the fuel pump circuit condition, the fuel pump ECU outputs a diagnostic signal (DI) to the ECM, and the ECM determines if there is a malfunction in the fuel pump circuit.
DTC Code
DTC Detection Condition
Trouble Area
P0230
When either condition below is met (1 trip detection logic):
  1. When the fuel pump is operating:
    1. The remaining fuel is 17 L or more.
    2. The DI terminal output is low.
  1. When the fuel pump is not operating:
    1. The DI terminal output is high.
  1. Open or short in fuel pump circuit
  2. Fuel pump
  3. Fuel pump ECU
  4. ECM

MONITOR DESCRIPTION

To monitor the fuel pump circuit, the ECM checks the fuel pump control signal (FPC) and diagnostic signal (DI). The FPC voltage varies between approximately 0 V to approximately 12 V (duty signal). Based on the condition of the fuel pump ECU malfunction, the DI voltage varies between approximately 0 V and approximately 12 V. The ECM then compares the variance of the FPC voltage and DI voltage, and determines if the fuel pump circuit is malfunctioning. When the ECM determines that the fuel pump circuit is malfunctioning, a DTC is stored immediately.

WIRING DIAGRAM

A264509E01
A264509E02

INSPECTION PROCEDURE

This troubleshooting procedure is based on the premise that the engine is started. If the engine is not started, proceed to the Problem Symptoms Table (Click here).

1. CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Body / (desired system) / DTC.

  1. Read the DTC.

    Result 
    Result
    Proceed to
    DTC B1500 is not output
    A
    DTC B1500 is output
    B



B
GO TO DTC B1500 (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the fuel pump / Speed.

  1. Check whether operating sounds can be heard while operating the relay using the tester.

    OK:
    Operating sounds can be heard from circuit opening relay.



NG
Go to step 6
OK


3. CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)
A180651E01
  1. Disconnect the fuel pump ECU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    N2-5 (FPC) - C45-59 (FPC)
    Always
    Below 1 Ω
    N2-4 (DI) - A38-19 (DI)
    Always
    Below 1 Ω
    N2-6 (E) - Body ground
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    N2-5 (FPC) - C46-59 (FPC)
    Always
    Below 1 Ω
    N2-4 (DI) - A52-19 (DI)
    Always
    Below 1 Ω
    N2-6 (E) - Body ground
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    N2-1 (FP-) - Body ground
    Always
    10 kΩ or higher
    N2-5 (FPC) or C45-59 (FPC) - Body ground
    Always
    10 kΩ or higher
    N2-4 (DI) or A38-19 (DI) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    N2-1 (FP-) - Body ground
    Always
    10 kΩ or higher
    N2-5 (FPC) or C46-59 (FPC) - Body ground
    Always
    10 kΩ or higher
    N2-4 (DI) or A52-19 (DI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. REPLACE FUEL PUMP ECU
  1. Replace the fuel pump ECU (Click here).


NEXT


5. CHECK WHETHER DTC OUTPUT RECURS
  1. Check that there are 17 liters or more of fuel remaining.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and idle it for 5 minutes.

  1. Drive the vehicle in an urban area for approximately 10 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No output
    A
    DTC P0230 is output
    B



B
REPLACE ECM (Click here)
A

END

6. INSPECT CIRCUIT OPENING RELAY (C/OPN)
  1. Inspect the circuit opening relay (C/OPN) (Click here).



NG
REPLACE CIRCUIT OPENING RELAY (C/OPN)
OK


7. INSPECT CIRCUIT OPENING RELAY (C/OPN) (POWER SOURCE VOLTAGE)
A162664E01
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C/OPN relay (2) - Body ground
    Ignition switch ON
    11 to 14 V
    C/OPN relay (5) - Body ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 14
OK


8. CHECK HARNESS AND CONNECTOR (C/OPN RELAY - ECM, FUEL PUMP ECU)
A180652E01
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Disconnect the fuel pump ECU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay (1) - A38-7 (FC)
    Always
    Below 1 Ω
    C/OPN relay (3) - N2-3 (+B)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay (1) - A52-7 (FC)
    Always
    Below 1 Ω
    C/OPN relay (3) - N2-3 (+B)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay (1) or A38-7 (FC) - Body ground
    Always
    10 kΩ or higher
    C/OPN relay (3) or N2-3 (+B) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay (1) or A52-7 (FC) - Body ground
    Always
    10 kΩ or higher
    C/OPN relay (3) or N2-3 (+B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)
A182228E01
  1. Disconnect the fuel sender gauge connector.

  1. Disconnect the fuel pump ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    N1-4 (B2) - N2-2 (FP)
    Always
    Below 1 Ω
    N1-5 (E2) - N2-1 (FP-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    N1-4 (B2) or N2-2 (FP) - Body ground
    Always
    10 kΩ or higher
    N1-5 (E2) or N2-1 (FP-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. INSPECT FUEL PUMP
  1. Inspect the fuel pump (for Single Tank Type) (Click here).

  1. Inspect the fuel pump (for Double Tank Type) (Click here).

    Result 
    Test Result
    Proceed to
    OK
    A
    NG (for Single Tank Type)
    B
    NG (for Double Tank Type)
    C



B
REPLACE FUEL PUMP (Click here)

C
REPLACE FUEL PUMP (Click here)
A


11. CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)
A180651E03
  1. Disconnect the fuel pump ECU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    N2-5 (FPC) - C45-59 (FPC)
    Always
    Below 1 Ω
    N2-4 (DI) - A38-19 (DI)
    Always
    Below 1 Ω
    N2-6 (E) - Body ground
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    N2-5 (FPC) - C46-59 (FPC)
    Always
    Below 1 Ω
    N2-4 (DI) - A52-19 (DI)
    Always
    Below 1 Ω
    N2-6 (E) - Body ground
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    N2-5 (FPC) or C45-59 (FPC) - Body ground
    Always
    10 kΩ or higher
    N2-4 (DI) or A38-19 (DI) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    N2-5 (FPC) or C46-59 (FPC) - Body ground
    Always
    10 kΩ or higher
    N2-4 (DI) or A52-19 (DI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12. REPLACE FUEL PUMP ECU
  1. Replace the fuel pump ECU (Click here).


NEXT


13. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and idle it for 5 minutes.

  1. Drive the vehicle in an urban area for approximately 10 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No output
    A
    DTC P0230 is output
    B



B
REPLACE ECM (Click here)
A

END

14. CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - IGN FUSE, INTEGRATION RELAY)
A162655E02
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Remove the IGN fuse from the engine room relay block.

  1. Remove the integration relay from the engine room relay block.

  1. Disconnect the 1B integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay (2) - IGN fuse (2)
    Always
    Below 1 Ω
    C/OPN relay (5) - 1B-4
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay (2) or IGN fuse (2) - Body ground
    Always
    10 kΩ or more
    C/OPN relay (5) or 1B-4 - Body ground
    Always
    10 kΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)


← P0171 System Too Lean (Bank 1) (+ P0172, P0174, P0175) (from Jan 2012)P0300 Random / Multiple Cylinder Misfire Detected (+ 6 more codes) (Sep 2011 – Dec 2011) →