P0617 Starter Relay Circuit High
Diagnostic trouble codes · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) or more for more than 20 seconds.
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Drive vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more |
Conditions (a), (b) and (c) are met for 20 seconds (a) Vehicle speed is more than 20 km/h (12.4 mph). (b) Engine speed is more than 1000 rpm. (c) STA signal is on. |
|
| DTC No. |
Data List |
| P0617 |
Starter Signal |
WIRING DIAGRAM








INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to the Problem Symptoms Table (Click here).
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
- The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to the Problem Symptoms Table (Click here).
| 1. CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM |
Check if the vehicle is equipped with the entry and start system.
Result Result
Proceed to
w/ Entry and Start System
A
w/o Entry and Start System
B
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.
- OK:
Ignition Switch Condition
Starter Signal
ON
OFF
Engine started
ON
Result Result
Proceed to
NG (A/T)
A
NG (M/T)
B
OK
C
|
|
||||
|
|
||||
| A | |
| 3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Inspect the park/neutral position switch (Click here).
Result Result
Proceed to
NG
A
OK
B
|
|
||||
| A | |
| 4. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Replace the park/neutral position switch (Click here).
|
|
||||
| 5. INSPECT CLUTCH START SWITCH |
Check the clutch start switch (for LHD) (Click here).
Check the clutch start switch (for RHD) (Click here).
| Result |
Proceed to |
| NG |
A |
| OK |
B |
|
|
||||
| A | |
| 6. REPLACE CLUTCH START SWITCH |
Replace the clutch start switch (for LHD) (Click here).
Replace the clutch start switch (for RHD) (Click here).
| NEXT | |
| 7. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.
- OK:
Ignition Switch Condition
Starter Signal
ON
OFF
Engine started
ON
Result Result
Proceed to
NG
A
OK
B
|
|
||||
| A | |
| 8. CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM) |
|
|
||||
| OK | |
| 9. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Drive the vehicle at 20 km/h (12.4 mph) or more for 20 seconds or more.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
Result Display (DTC Output)
Proceed to
P0617
A
No output
B
|
|
||||
| A | ||
| ||
| 10. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.
- OK:
Ignition Switch Condition
Starter Signal
ON
OFF
Engine started
ON
Result Result
Proceed to
NG (A/T)
A
NG (M/T)
B
OK
C
|
|
||||
|
|
||||
| A | |
| 11. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Inspect the park/neutral position switch (Click here).
Result Result
Proceed to
NG
A
OK
B
|
|
||||
| A | |
| 12. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Replace the park/neutral position switch (Click here).
|
|
||||
| 13. INSPECT CLUTCH START SWITCH ASSEMBLY |
Check the clutch start switch (for LHD) (Click here).
Check the clutch start switch (for RHD) (Click here).
| Result |
Proceed to |
| NG |
A |
| OK |
B |
|
|
||||
| A | |
| 14. REPLACE CLUTCH START SWITCH ASSEMBLY |
Replace the clutch start switch (for LHD) (Click here).
Replace the clutch start switch (for RHD) (Click here).
|
|
||||
| 15. INSPECT IGNITION OR STARTER SWITCH ASSEMBLY |
Inspect the Ignition or Starter Switch Assembly (Click here).
| Result |
Proceed to |
| NG |
A |
| OK |
B |
|
|
||||
| A | |
| 16. REPLACE IGNITION OR STARTER SWITCH ASSEMBLY |
Replace the Ignition or Starter Switch Assembly (Click here).
| NEXT | |
| 17. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.
- OK:
Ignition Switch Condition
Starter Signal
ON
OFF
Engine started
ON
Result Result
Proceed to
NG
A
OK
B
|
|
||||
| A | |
| 18. CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM) |
|
|
||||
| OK | |
| 19. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Drive the vehicle at 20 km/h (12.4 mph) or more for 20 seconds or more.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
Result Display (DTC Output)
Proceed to
P0617
A
No output
B
|
|
||||
| A | ||
| ||
