2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0617 Starter Relay Circuit High

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.
If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) or more for more than 20 seconds.
P0617 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Drive vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more
Conditions (a), (b) and (c) are met for 20 seconds
(a) Vehicle speed is more than 20 km/h (12.4 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
  1. Park/neutral position switch (A/T)
  2. Starter relay circuit
  3. Clutch start switch (M/T)
Related Data List 
DTC No.
Data List
P0617
Starter Signal

WIRING DIAGRAM

A263237E01
A263237E02
A263238E01
A263238E03

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to the Problem Symptoms Table (Click here).
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
  1. Check if the vehicle is equipped with the entry and start system.

    Result 
    Result
    Proceed to
    w/ Entry and Start System
    A
    w/o Entry and Start System
    B



B
Go to step 10
A


2. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.

    OK:
    Ignition Switch Condition
    Starter Signal
    ON
    OFF
    Engine started
    ON

    Result 
    Result
    Proceed to
    NG (A/T)
    A
    NG (M/T)
    B
    OK
    C



B
Go to step 5

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch (Click here).

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 8
A


4. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Replace the park/neutral position switch (Click here).



NEXT
Go to step 7
5. INSPECT CLUTCH START SWITCH
  1. Check the clutch start switch (for LHD) (Click here).

  1. Check the clutch start switch (for RHD) (Click here).

Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 8
A


6. REPLACE CLUTCH START SWITCH
  1. Replace the clutch start switch (for LHD) (Click here).

  1. Replace the clutch start switch (for RHD) (Click here).


NEXT


7. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.

    OK:
    Ignition Switch Condition
    Starter Signal
    ON
    OFF
    Engine started
    ON

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
SYSTEM OK
A


8. CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM)


NG
REPLACE HARNESS OR CONNECTOR
OK


9. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle at 20 km/h (12.4 mph) or more for 20 seconds or more.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result 
    Display (DTC Output)
    Proceed to
    P0617
    A
    No output
    B



B
SYSTEM OK
A

GO TO CRANKING HOLDING FUNCTION CIRCUIT (Click here)

10. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.

    OK:
    Ignition Switch Condition
    Starter Signal
    ON
    OFF
    Engine started
    ON

    Result 
    Result
    Proceed to
    NG (A/T)
    A
    NG (M/T)
    B
    OK
    C



B
Go to step 13

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


11. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch (Click here).

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 15
A


12. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Replace the park/neutral position switch (Click here).



NEXT
Go to step 17
13. INSPECT CLUTCH START SWITCH ASSEMBLY
  1. Check the clutch start switch (for LHD) (Click here).

  1. Check the clutch start switch (for RHD) (Click here).

Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 15
A


14. REPLACE CLUTCH START SWITCH ASSEMBLY
  1. Replace the clutch start switch (for LHD) (Click here).

  1. Replace the clutch start switch (for RHD) (Click here).



NEXT
Go to step 17
15. INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
  1. Inspect the Ignition or Starter Switch Assembly (Click here).

Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 18
A


16. REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
  1. Replace the Ignition or Starter Switch Assembly (Click here).


NEXT


17. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.

    OK:
    Ignition Switch Condition
    Starter Signal
    ON
    OFF
    Engine started
    ON

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
SYSTEM OK
A


18. CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM)


NG
REPLACE HARNESS OR CONNECTOR
OK


19. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle at 20 km/h (12.4 mph) or more for 20 seconds or more.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result 
    Display (DTC Output)
    Proceed to
    P0617
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)


← P0606 ECM / PCM Processor (+ P0607, P1611) (from Jan 2012)P0617 Starter Relay Circuit High (from Jan 2012) →